Vortex FURY HD 5000 Manual de usuario

PRODUCT MANUAL

LASER RANGEFINDING BINOCULARS

FURY®HD 5000

2 3

FURY®HD 5000

Ocular Lens

Center Focus

Twist-up Eyecup

Strap

Attachment

Reticle Focus Diopter Focus

Measure Button

Menu Button

Tripod Adapter Socket

Objective Lens

FURY®HD 5000 LASER RANGEFINDING BINOCULAR

The Fury®HD 5000 is an extremely effective angle-compensated

laser rangeﬁnding binocular intended for hunters, archers and

shooters. The primary HCD (Horizontal Component Distance)

mode provides key angle compensated range information required

by the vast majority of riﬂe and bow shooters in a simple,

quick-to-read display.

The Fury®HD 5000 also has a LOS (Line of Sight) mode and Scan

feature, along with adjustments for reading in yards or meters and

setting the brightness of the display.

Images are for representation only. Product may vary slightly from

what is shown.

2 3

FURY®HD 5000

Ocular Lens

Center Focus

Twist-up Eyecup

Strap

Attachment

Reticle Focus Diopter Focus

Measure Button

Menu Button

Tripod Adapter Socket

Objective Lens

FURY®HD 5000 LASER RANGEFINDING BINOCULAR

The Fury®HD 5000 is an extremely effective angle-compensated

laser rangeﬁnding binocular intended for hunters, archers and

shooters. The primary HCD (Horizontal Component Distance)

mode provides key angle compensated range information required

by the vast majority of riﬂe and bow shooters in a simple,

quick-to-read display.

The Fury®HD 5000 also has a LOS (Line of Sight) mode and Scan

feature, along with adjustments for reading in yards or meters and

setting the brightness of the display.

Images are for representation only. Product may vary slightly from

what is shown.

4 5

FURY®HD 5000

BASIC OPERATION

Adjust the Eyecups

The eyecups on a Fury®HD 5000

twist up and down so any viewer can

see the full ﬁeld and enjoy

comfortable viewing—with or

without eyeglasses.

When not using eyeglasses or

sunglasses, keep the eyecups

fully extended. For best viewing

when wearing eyeglasses, twist

eyecups down.

Adjust the Interpupillary Distance

The interpupillary distance (IPD) is the distance between the

centers of the left and right eye pupils. Match the IPD of your eyes

to that of the binocular so you see a single image free of shading.

Rotate the binocular barrels inward or outward to line your eyes up

with ocular lenses.

–

Install Battery

Open the battery compartment and

install the CR2 battery included with

the Fury® HD 5000.

Install battery with

positive side facing in.

Power Up

To power up the Fury®HD 5000 and

prepare for ranging, press and release

the Measure button. The HCD or LOS

ranging screen will display. The Fury®

will power down automatically after

ten seconds of non-use.

Low Battery Icon

The low battery icon comes on at 25%

and stays on until there is no power.

4 5

FURY®HD 5000

BASIC OPERATION

Adjust the Eyecups

The eyecups on a Fury®HD 5000

twist up and down so any viewer can

see the full ﬁeld and enjoy

comfortable viewing—with or

without eyeglasses.

When not using eyeglasses or

sunglasses, keep the eyecups

fully extended. For best viewing

when wearing eyeglasses, twist

eyecups down.

Adjust the Interpupillary Distance

The interpupillary distance (IPD) is the distance between the

centers of the left and right eye pupils. Match the IPD of your eyes

to that of the binocular so you see a single image free of shading.

Rotate the binocular barrels inward or outward to line your eyes up

with ocular lenses.

–

Install Battery

Open the battery compartment and

install the CR2 battery included with

the Fury® HD 5000.

Install battery with

positive side facing in.

Power Up

To power up the Fury®HD 5000 and

prepare for ranging, press and release

the Measure button. The HCD or LOS

ranging screen will display. The Fury®

will power down automatically after

ten seconds of non-use.

Low Battery Icon

The low battery icon comes on at 25%

and stays on until there is no power.

6 7

FURY®HD 5000

Mode Selection Display

Menu Button

Measure Button

Properly Focus the Rangeﬁnding

Display and Binocular

For the best views, follow this process to

properly set the display, center focus, and

diopter. Choose an object that is about

20 yards away from you and stay in the

same spot until you have adjusted the

binocular for your eyes.

1. Power up the binocular and close your

left eye.

2. While viewing the rangeﬁnding display

with your right eye, focus your right

eye on the object and adjust the

center focus wheel until the object is

in focus. Leave the center focus wheel

in this position.

3. Then, using the reticle focus

adjustment ring, adjust the reticle

focus to bring the display into sharp

focus. Once this is done, you will

not have to refocus the rangeﬁnding

display again.

4. Close your right eye or cover the right

objective lens with your hand. Looking

at the object with your left eye, adjust

the diopter so the object is in focus.

Make note of this diopter setting in

case you need to set it again. From

this point on, you will only need to use

the center focus wheel.

Adjust Reticle Focus Ring

Mode Selection

Your Fury® HD 5000 is factory set to the angle compensating

HCD ranging mode, best target mode, yards, and maximum

brightness. For most users, these are the preferred settings.

To change modes: Press and release the Measure button to

power on and then press and hold the Menu button for at least

four seconds. Once the Mode Selection screen displays, release

the button.

As you progress through Mode Selection, you may exit at any

time and save your settings by pressing and holding the Menu

button for at least four seconds—the Fury®will return to

power-up condition.

6 7

FURY®HD 5000

Mode Selection Display

Menu Button

Measure Button

Properly Focus the Rangeﬁnding

Display and Binocular

For the best views, follow this process to

properly set the display, center focus, and

diopter. Choose an object that is about

20 yards away from you and stay in the

same spot until you have adjusted the

binocular for your eyes.

1. Power up the binocular and close your

left eye.

2. While viewing the rangeﬁnding display

with your right eye, focus your right

eye on the object and adjust the

center focus wheel until the object is

in focus. Leave the center focus wheel

in this position.

3. Then, using the reticle focus

adjustment ring, adjust the reticle

focus to bring the display into sharp

focus. Once this is done, you will

not have to refocus the rangeﬁnding

display again.

4. Close your right eye or cover the right

objective lens with your hand. Looking

at the object with your left eye, adjust

the diopter so the object is in focus.

Make note of this diopter setting in

case you need to set it again. From

this point on, you will only need to use

the center focus wheel.

Adjust Reticle Focus Ring

Mode Selection

Your Fury® HD 5000 is factory set to the angle compensating

HCD ranging mode, best target mode, yards, and maximum

brightness. For most users, these are the preferred settings.

To change modes: Press and release the Measure button to

power on and then press and hold the Menu button for at least

four seconds. Once the Mode Selection screen displays, release

the button.

As you progress through Mode Selection, you may exit at any

time and save your settings by pressing and holding the Menu

button for at least four seconds—the Fury®will return to

power-up condition.

8 9

FURY®HD 5000

SET AND SAVE MODE SELECTIONS

Ranging Mode Selection

Choose Between the HCD and LOS Modes.

After activating the Mode Selection, press the Measure button

to toggle between the HCD and LOS displays. Press the Menu

button to save your desired choice and move to the Yards/Meters

selection screen.

Display Selection

Choose Between Yards and Meters Display.

Press the Measure button to toggle between the Yards and Meters

display. Press the Menu button to save your desired choice and

move to the Brightness selection screen.

Brightness Selection

Choose Between Five Brightness Settings.

The Fury® HD 5000 provides ﬁve

illumination settings. Press the Measure

button to toggle through the ﬁve Brightness

settings. Press the Menu button to save

your desired setting and move back to the

target mode selection.

Target Mode Selection

Target Mode Explanations

The Fury®HD 5000 provides two target modes: Best Mode and

Last Mode.

Best Mode

Your Fury®HD 5000 comes preset to Best target mode. This is

the standard mode providing the range of the target with the

strongest range result. Best Mode is the recommended target

mode for most situations.

Last Mode

Displays the farthest distance when panning and scanning. This

mode is ideal for ranging a speciﬁc target behind a group of objects

like brush, trees, rocks, etc.

8 9

FURY®HD 5000

SET AND SAVE MODE SELECTIONS

Ranging Mode Selection

Choose Between the HCD and LOS Modes.

After activating the Mode Selection, press the Measure button

to toggle between the HCD and LOS displays. Press the Menu

button to save your desired choice and move to the Yards/Meters

selection screen.

Display Selection

Choose Between Yards and Meters Display.

Press the Measure button to toggle between the Yards and Meters

display. Press the Menu button to save your desired choice and

move to the Brightness selection screen.

Brightness Selection

Choose Between Five Brightness Settings.

The Fury® HD 5000 provides ﬁve

illumination settings. Press the Measure

button to toggle through the ﬁve Brightness

settings. Press the Menu button to save

your desired setting and move back to the

target mode selection.

Target Mode Selection

Target Mode Explanations

The Fury®HD 5000 provides two target modes: Best Mode and

Last Mode.

Best Mode

Your Fury®HD 5000 comes preset to Best target mode. This is

the standard mode providing the range of the target with the

strongest range result. Best Mode is the recommended target

mode for most situations.

Last Mode

Displays the farthest distance when panning and scanning. This

mode is ideal for ranging a speciﬁc target behind a group of objects

like brush, trees, rocks, etc.

10 11

FURY®HD 5000

Scan Ranging

Activate Scan Ranging by pressing and holding the Measure

button down. Keeping the button depressed will continuously

measure distance as you pan back and forth across target objects.

The aiming circle will blink as you pan. Releasing the Measure

button will return laser to the Power Up Condition.

HCD Scan LOS Scan

No Range

Returned

Setting Target Modes

Press the Measure button to toggle between the Best and Last

displays. Press the Menu button to save your desired choice and

move back to the HCD/LOS selection screen.

To exit Mode Selection and save settings, press and hold the Menu

button for four seconds. Settings will also save when Fury®powers

down automatically.

Ranging

With the Fury® HD 5000 powered up,

position the reticle on the target object

and press and release the Measure button

to get the distance measurement. If

the laser is not able to range due to the

reﬂectivity of the target, you will see a

display similar to that shown here. To

range a new target, simply re-aim and

press the Measure button again.

Otros manuales para FURY HD 5000

Tabla de contenidos

Otros manuales de Prismáticos de Vortex

Vortex

Vortex VIPER HD Manual de usuario

Vortex

Vortex Viper Series Manual de usuario

Vortex

Vortex FURY Manual de usuario

Vortex

Vortex Solo 25 mm Manual de usuario

Vortex

Vortex Viper HD Manual de usuario

Vortex

Vortex Raptor Manual de usuario

Vortex

Vortex VULTURE HD Manual de usuario

Vortex

Vortex Vulture HD Manual de usuario

Vortex

Vortex BIN-DBK-12A Instrucciones de montaje

Vortex

Vortex VANQUISH VNQ-1026 Manual de usuario

Vortex

Vortex CROSSFIRE Manual de usuario

Vortex

Vortex DB-205 Manual de usuario

Vortex

Vortex FURY HD 5000 AB Manual de usuario

Vortex

Vortex Viper Manual de usuario

Vortex

Vortex Razor HD Manual de usuario

Vortex

Vortex Viper 10x32 Manual de usuario

Vortex

Vortex Vanquish Manual de usuario

Vortex

Vortex Diamondback 10x28 Manual de usuario

Vortex

Vortex SOLO R Manual de usuario

Vortex

Vortex Vulture 10x56 Manual de usuario

Vortex

Vortex FURY HD 5000 Manual de usuario

Vortex

Vortex TALON HD 10x42 Manual de usuario

Vortex

Vortex Raptor 6.5x32 Manual de usuario

Vortex

Vortex Kaibab HD Manual de usuario

Manuales populares de Prismáticos de otras marcas

Celestron

Celestron VistaPix 72218 Manual de usuario

Levenhuk

Levenhuk Atom Digital DNM200 Manual de usuario

ATN

ATN PS-15 Manual de usuario

Bresser

Bresser TOPAS 7x50 Manual de usuario

Berger & Schroter

Berger & Schroter LN-G3-B50 Manual de usuario

Leica

Leica geovid 8x42 HD-R Manual de usuario

Noblex

Noblex NF 8 x 42 inception Manual de usuario

Newcon Optik

Newcon Optik AN Series Manual de usuario

PHOTONIS

PHOTONIS VYPER Manual de usuario

ATN

ATN 6015-WPT Manual de usuario

Famous Trails

Famous Trails ViewCatcher DCB 822 Manual de usuario

AGM

AGM EXPLORATOR FSB50-640 Manual de usuario

Opticron

Opticron Marine-3 7x50 BIF.GA Guía de instalación

Kayoba

Kayoba 009129 Manual de usuario

Vixen

Vixen ARENA Series Manual de usuario

MAGINON

MAGINON NVB 60 Manual de usuario

Leica

Leica Geovid 56 Manual de usuario

Leica

Leica GEOVID PRO Manual de usuario