VOLTCRAFT SL-300 Manual de usuario
SOUND LEVEL
METER
INSTRUCTION MANUAL
REC
FAST
A/C
1. SAFETY INFORMATION
Read the following safety information carefully
before attempting to operate or service the meter.
2
Use the meter only as specified in this manual
zEnvironment conditions
Altitude lower than 2000 meters
Relatively humidity ≤90RH
Operation Ambient 0 ~ 40
zMaintenance & Clearing
Repair or servicing not covered in this
manual should be performed by qualified
personnel.
Periodically wipe the case with a dry
cloth. Do not use solvents or eradicator on
this instrument.
zSafety symbols
Comply with EMC
2. FUNCTIONS DESCRIPTION
This Sound Level Meter is designed for
noise project; quality control; illness prevention and
cure and all kinds of environmental sounds
measurement. It is applied to the sounds
measurement at factory; school; office; traffic
access and household, etc.
zThis unit confirms to the IEC61672-1
CLASS2 for Sound Level Meters.
zMAX & MIN measurements
zOver range display
zUnder range display
zA & C Weighting
3
zFAST & SLOW response
zAnalog AC/DC outputs for connection to
frequency analyzer or X-Y shaft recorder
3. SPECIFICATION
Standard applied: IEC61672 -1 CLASS2
Accuracy: +1.4dB
Frequency range: 31.5HZ ~ 8KHZ
Dynamic range: 50dB
Level ranges: LO30dB~80dB
Med50dB~100dB
Hi80dB~130dB
Auto30dB~130dB
Frequency weighting: A/C
Time weighting: FAST ( 125ms ), SLOW (
1s )
Microphone: 1/2 inch electret condenser
microphone
Display: 4 digits LCD display with a
resolution of 0.1dB
Display Update: 2 times/sec.
MAX hold: Hold the Maximum reading
MIN hold: Hold the Minimum reading
HOLD: Hold the readings
Alarm function: “OVER”is when input is
more than upper limit of range.
“UNDER”is when input is less than upper limit
of range.
Analog output : AC/DC outputs from
4
earphone outlet
AC=1Vrms DC=10mV/dB
Data output : USB data traffic
Auto power off : Meter automatically shuts
down after approx. 15 minutes of inactivity.
Power supply : One 9V battery, 006P or
NEDA1604 or IEC 6F22.
Power life : About 50hours
Operation temperature and humidity:
0~40,10RH~90RH
Storage temperature and temperature:
-10~+6010RH~75RH
Dimension : 278 (L) x 76 (W) x 50(H) mm
Weight : 350g
Accessories : Instruction manual, battery,
screwdriver, 3.5mm earphone plug,
windscreen, software, USB cable, tripod and
DC 9V power supply.
4. NAME AND FUNCTIONS
REC
FAST
A/C
1
2
3
4
5
8
6
7
10
9
11
5
DC 9V
OUTPUT
CAL
18
12
13
14
15
16
17
Windscreen
LCD
SYMBOL FUNCTION
LCD 4 digits
MAX Maximum hold
MIN Minimum hold
6
OVER over range
UNDER under range
FAST Fast response
SLOW Slow response
dBA A-Weighting(responseto human
sense)
dBC C-Weighting(response to
machine monitor)
88—180 Range indicate
REC Recording data into computer
AUTO Auto level range selection
FULL Memory full
HOLD Data hold function
AutopoweroffPress the”SETUP“
button to disable power off
Low battery indicate
REC button
3.0 DATALOGGER function
Press “REC” button after it power on, the display
will show “REC” to start Data Recordingpress the
button again to delet the record (Note: In order to
avoid data error, please don’t power it off under
REC condition, when the REC function is deleted
then it can power off).
3.1 Adjusting DATALOGGER response
7
Press the button continuously before power it
onthen press it will be displayed as
following
Press‘LEVEL’button to adjust memory timepress
‘HOLD’ button to hold the setup
3.2 Data zero function
Press the button continuously before power it
onloosen the
button when the display showing‘CLR’ after the
meter
power onwhich indicates that the data in
DATALOGGER has been deleted.
SETUP button
40The time chip adjustment
Press‘SETUP’button and then power it
onwhen‘TIME’symbol displays then
loosen‘SETUP’the meter will be under time
adjustment modeat the time the display will
show the date as following
8
Press the‘SETUP’button second time, the display
showing
The display showing “minute” adjustment mode,
press ‘LEVEL’ to
make the adjustmentpress ‘HOLD’to keep the
setup
Press the‘SETUP’button third time, the display
showing
The display showing “hour” adjustment mode,
press ‘LEVEL’ to
make the adjustmentpress‘HOLD’to keep the
setup
Press the‘SETUP’button fourth time, the display
showing
The display showing “date” adjustment mode, press
9
‘LEVEL’ to make the adjustmentpress‘HOLD’to
keep the setup
Press the‘SETUP’button fifth time, the display
showing
The display showing “month” adjustment mode,
press ‘LEVEL’ to
make the adjustmentpress ‘HOLD’ to keep the
setup
Press the‘SETUP’button sixth time, the display
showing
The display showing “year” adjustment mode,
press ‘LEVEL’ to
make the adjustmentpress ‘HOLD’to keep the
setup
Press the‘SETUP’button seventh and eighth time,
the display showing separately as following
The display showing default range, which can’t be
adjusted.
10
Press the‘SETUP’button ninth time, the display
showing
The display showing initialization of the time
chiptime and date have returned to factory setup.
When the battery is exhausted or replaced, if the
time can’t be adjusted then please initialize the time
chip first.
41USB communications
settingturn on the meter, connect the meter
with the computer correctly, choose the software
COM3COM4then press ‘SETUP’‘ ’
disappears from the display to indicate and disable
auto power off, that the USB data is transmitting.
FAST/SLOW button:
time weighting selection
FASTFast sampling measurement, 1 time per
125mS.
SLOWSlow sampling measurement, 1 time per
second.
MAX/MIN button: Maximum and Minimum
Tabla de contenidos
Otros manuales de Instrumento de medición de VOLTCRAFT
VOLTCRAFT
VOLTCRAFT DVM-230 Manual de usuario
VOLTCRAFT
VOLTCRAFT FM-HP 40 92 37 Manual de usuario
VOLTCRAFT
VOLTCRAFT SEM-5000 PRO Guía de referencia
VOLTCRAFT
VOLTCRAFT LCR-100 Manual de usuario
VOLTCRAFT
VOLTCRAFT 2583086 Manual de usuario
VOLTCRAFT
VOLTCRAFT UM5/1 200 Manual de usuario
VOLTCRAFT
VOLTCRAFT DL-160S Manual de usuario
VOLTCRAFT
VOLTCRAFT AM-96X96 Manual de usuario
VOLTCRAFT
VOLTCRAFT Luxmeter LX-10 Manual de usuario
VOLTCRAFT
VOLTCRAFT CO-60 Manual de usuario
VOLTCRAFT
VOLTCRAFT PM-37 Manual de usuario
VOLTCRAFT
VOLTCRAFT ENERGY MONITOR 3000 Manual de usuario
VOLTCRAFT
VOLTCRAFT SEM6500 CH Manual de usuario
VOLTCRAFT
VOLTCRAFT Energy Check 3000 Manual de usuario
VOLTCRAFT
VOLTCRAFT PL-130 AN Manual de usuario
VOLTCRAFT
VOLTCRAFT BT-2 Manual de usuario
VOLTCRAFT
VOLTCRAFT AM-72X72 Manual de usuario
VOLTCRAFT
VOLTCRAFT Energy Logger 4000 Manual de usuario
VOLTCRAFT
VOLTCRAFT GM-100 Manual de usuario
VOLTCRAFT
VOLTCRAFT 12 95 18 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario