VOLKTEK INS-801W Manual de usuario
5-port 10/100Base-TX
Industrial Switch
(INS-801 / INS-801W)
User’s Guide
COPYRIGHT
All rights reserved. No part of this publication may be reproduced,
stored in a retrieval system or transmitted in any form or by any means,
whether electronic, mechanical, photo copying, recording or otherwise,
without the prior written permission of the publisher.
FCC WARNING
This equipment has been tested and found to comply with the
limits for a class A device, pursuant to part 15 of FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a commercial installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communication. Operating this equipment
in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at the user’s
own expense.
CE
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the user
may be required to take adequate measures.
Take special care to read and understand all content given in the
warning boxes
Warning
TA BL E O F CONTEN TS
ABOUT THIS GUIDE............................................................ 4
TERMS/USAGE ....................................................................... 4
INTRODUCTION ................................................................... 4
INDUSTRIAL ETHERNET TECHNOLOGY .................................. 5
SWITCHING TECHNOLOGY ..................................................... 5
FEATURES .............................................................................. 6
INS-801 INDUSTRIAL SWITCH - UNPACKING AND
SET-UP ................................................................................... 7
UNPACKING ........................................................................... 7
LAYOUT OF THE INS-801/801W............................................ 8
DIN-RAIL MOUNTING OF THE INS-801/801W ..................... 10
REDUNDANT POWER INPUTS................................................ 11
CONFIGURING DC POWER INPUTS........................................ 11
ETHERNET CONNECTIONS.................................................... 13
LED INDICATORS ................................................................ 14
EXTERNAL ALARM CONTACT .............................................. 14
DIP-SWITCH SETTINGS ........................................................ 15
AUTO-NEGOTIATION ............................................................ 16
SWITCHING,FILTERING,AND FORWARDING ........................ 17
PORT SPEED &DUPLEX MODE ............................................ 17
TECHNICAL SPECIFICATIONS ...................................... 18
APPENDIX ........................................................................... 19
4
ABO U T THI S GU I D E
The INS-801/INS-801W Industrial Series Switch is a hardened,
5-port Ethernet Switch with redundant DC power inputs –
designed to provide a reliable and economical solution for your
industrial Ethernet environment. With its dry contact smart
alarm, the INS-801/801W can initiate a physical alarm (audible
and/or visible) in the event of a malfunction. The INS-801
operates in a wide temperature range, from -10 to 70°C (from -
40°C in the case of the 801W), and is designed to handle
higher than normal degrees of vibration and shock, making it
suitable for harsh industrial environments.
This manual discusses how to install the INS-801 Industrial Fast
Ethernet Switch.
The INS-801Wis able to operate in a wider temperature range
(from -40°C to 70°C). The rest of the features and functions are
the same as the INS-801.
Terms/Usage
In this guide, the term “Switch” (first letter uppercase) refers to
the INS-801/801W Industrial Fast Ethernet Switch, and ”switch”
(first letter lowercase) refers to all other Ethernet switches.
In this guide, the term INS-801 will also refer to the INS-801W.
INT R O D U C TI O N
This chapter describes the features of the Switch and
some background information about Ethernet/Fast
Ethernet switching technology.
5
Industrial Ethernet Technology
The growing importance of Ethernet has extended to the factory
floor and industrial environments, where things have become
too harsh for typical commercial-grade networking equipment.
VOLKTEK has created an Industrial Series of Switches and
interconnecting devices specifically for the purpose of extending
Ethernet to the factory floor and industrial environments. All of
our Industrial Series devices are delivered in a rugged,
hardened case and with components capable of withstanding a
high degree of vibration and shock. These devices also operate
well in temperatures as high as 70°C.
Not an ordinary office switch by any means, the INS-801 is
engineered and designed specifically for the harsh, industrial-
type environments commonly encountered in heavy industry.
With its redundant DC power inputs and high-performance
components, the INS-801 is perfectly suited for the industrial
Ethernet.
Switching Technology
One way to push the limits of Ethernet technology, is the
development of switching technology. A switch bridges Ethernet
packets at the MAC address level of the Ethernet protocol that
are transmitted between connected Ethernet or Fast Ethernet
LAN segments.
Switching is a cost-effective way of increasing the total network
capacity available to users on a local area network. A switch
increases capacity and decreases network loading by dividing a
local area network into different segments which don’t compete
with each other for network transmission capacity.
6
Features
The Switch was designed for easy installation and high
performance in an industrial environment where vibration, shock,
heat, and RF interference may be commonplace.
The Switch was specifically designed to be small and compact
for easy DIN-rail mounting and it can be installed where space
is limited.
The Switch is ideal for deployment with multiple high-speed
servers for shared-bandwidth 10Mbps or 100Mbps workgroups.
With a maximum bandwidth of 200Mbps (100Mbps full-duplex
mode), any port can provide workstations with a congestion-free
data pipe for simultaneous access to the server.
The Switch can be expanded by cascading two or more
switches together in a ‘daisy chain’. As all ports support
200Mbps (half-duplex), the Switch can be cascaded from any
port and to any number of switches.
The Switch combines dynamic memory allocation with store-
and-forward switching to ensure that the buffer is effectively
allocated for each port, while controlling the data flow between
the transmit and receive nodes to guarantee against all possible
packet loss.
The Switch is an unmanaged 10/100Mbps Fast Ethernet Switch
that offers solutions for increasing the bandwidth and speed of
small Ethernet workgroups.
Other key features are:
oFive (5) 10/100Base-TX ports
7
oRugged, hardened IP30 case
oVibration/Shock operational
oPower terminal block
oWide voltage range: 9-48V
oDIP-switch to enable or disable alarm functions
oPower input polarity protection function
oUnder-power and over-power detection function
oWide operating temp.: -40°C ~ 70°C for the INS-801W
oStore-and-forwarding
oAuto-negotiation at all copper ports
INS-801 IN D U S T R IA L SW I T C H -
UN PA CK I NG AN D SET-U P
This section and the following sections explain the set-up
and installation of the VOLKTEK INS-801/801W
Industrial Switch.
Unpacking
Open the box of the Switch and carefully unpack it. The
box should contain the following items:
One INS-801 5-port 10/100M Industrial Fast Ethernet
Switch
One DIN-rail bracket
Protective caps for unused ports
Quick Installation Guide
This User’s Guide CD
If any item is found missing or damaged, please contact
8
your local reseller for replacement.
Layout of the INS-801/801W
Front View of Switch
8
9
10
1. Alarm LED
2. Redundant Power LED
3. Primary Power LED
4. TX ports (5)
5. TX port 100Mbps LED
6. TX port LNK/ACT LED
1
2
3
4
5
6
9
TOP View of Switch
Back View of Switch
Din Rail
Bracket
Screws
Grounding
Screw
Terminal block for
power input
(PWR/RPS), and alarm
dry contact
DIP-switches
10
DIN-rail mounting of the INS-801/801W
The aluminum DIN-rail attachment plate should already
be affixed to the back panel of the Switch. If you need to
attach the DIN-rail plate, assure that the stiff metal spring
is situated towards the top. Attaching the Switch to the
DIN-rail is easy: just align and hook it over the top rail,
making sure that the metal spring (thin bent rod) is in
front of the rail edge as the rail edge bites into the space
behind this spring, then press down and press the
Switch forward to snap into the bottom rail, as shown in
the figures below.
The set-up of the Switch can be performed after checking
the following facts:
•The hanging structure must support at least 1.0 Kg
for the Switch.
•The power outlet should be within 1.82 meters (6 feet)
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de VOLKTEK
VOLKTEK
VOLKTEK NSH-2926 Manual de usuario
VOLKTEK
VOLKTEK IEN-8428P-24V Manual de usuario
VOLKTEK
VOLKTEK INS-8424P Manual de usuario
VOLKTEK
VOLKTEK HNS-8415P Manual de usuario
VOLKTEK
VOLKTEK INS-802 Manual de usuario
VOLKTEK
VOLKTEK NSH-5632 Manual de usuario
VOLKTEK
VOLKTEK NSH-9309 Manual de usuario
VOLKTEK
VOLKTEK NSH-9308P Manual de usuario
VOLKTEK
VOLKTEK NSH-5509 Manual de usuario
VOLKTEK
VOLKTEK INS-806 Manual de usuario
