Vivotek IP8130 Manual de usuario

Quick Installation Guide

VIVOTEK INC.

6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.

|T:+886-2-82455282|F:+886-2-82455532|E:[email protected]

VIVOTEK USA, INC.

2050 Ringwood Avenue, San Jose, CA 95131

|T: 408-773-8686|F: 408-773-8298|E: [email protected]

IP8130/8131: 1MP • Compact Size

IP8130W/8131W: 1MP • 802.11n WLAN • WPS

All specications are subject to change without notice.

P/N:625021700G Rev. 1.0

IP8130/8131

Cube

Network Camera

English 繁中日本語 Español Português

簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska

Dansk

Nederlands

Indonesia

IP8130W/8131W

EN - 1

English

Power off the Network Camera as

soon as smoke or unusual odors are

detected.

Keep the Network Camera away

from water. If the Network Camera

becomes wet, power off immediately.

Do not place the Network Camera

around heat sources, such as a

television or oven.

Refer to your user’s manual for the

operating temperature.

Keep the Network Camera away from

direct sunlight.

Do not place the Network Camera in

high humidity environments.

Warning Before Installation

Do not place the Network Camera on

unsteady surfaces.

Do not touch the Network Camera

during a lightning storm.

Do not disassemble the Network

Camera.

Do not drop the Network Camera.

Do not insert sharp or tiny objects

into the Network Camera.

Camera Stand

IP8130W

Warranty Card

Screws

Quick Installation Guide

Power Adaptor (+12V, 1A)

Package Contents

Software CD

IP8131W

Ethernet Cable

Antenna

IP8130 IP8131

EN - 2

Physical Description

Front Panel

Status LED

Lens

Microphone

IP8130/8130W

IP8131/8131W

Microphone

IR LEDs

Status LED

Item LED status Description

LED Denitions

1 Steady Red Powered on, during system boot, or

indicating no network connection

All LED off Powered off

2 Blinking Blue every 0.15 sec. Searching for WPS

3 Blinking Green every 1 sec. Network connected (wired or wireless)

4 Blinking Green and RED

intermittently Upgrading rmware

5 Blinking Orange every 0.15 sec. Restoring default

WPS

MicroSD/SDHC/

SDXC Card Slot

Lens

WPS button

EN - 3

English

Back Panel The back panels are identical for all models.

Power Cord

Socket

Reset Button

Ethernet 10/100

RJ45 Socket

General I/O

Terminal Block

1 DI-

2 DI+

3 Audio GND

4 Audio Out Audio out cable is user-supplied.

Antenna Connector

(for wireless models)

Install Camera to Stand

Attach the camera to stand and orient the shooting angle. If preferred, use the included

screws to secure the the camera stand to a mounting surface.

EN - 4

Network Deployment

1. If you have external devices such as sensors and alarms, make connections from the

general I/O terminal block.

LAN Connection

POWER COLLISION

LINK

RECEIVE

PARTITION

12345

3. Connect the supplied power cable from

the camera to a power outlet.

2. Connect the camera to a switch via Ethernet cable or directly to a computer. Ethernet

must be connected before power on.

Install the Antenna (wireless models)

An antenna comes with the camera. Install it by turning clockwise to attach to the

connector.

EN - 5

English

MAC:0002D132C353

IP8130W

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Pat. 6,930,709

The following is performed on a computer connected to the same domain via a wired or

wireless connection.

1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.

2. The program will conduct an analysis of your network environment. After your network is

analyzed, please click on the “Next” button to continue the program.

0002D132C353

00-02-D1-32-C3-53 192.168.5.151 IP8130W

Installation

Wizard 2

Assigning an IP Address

2012/11/05 01:50:28

3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network

Cameras on the same LAN.

4. After a brief search, the main installer window will pop up. Double-click on the MAC

address that matches the one printed on the camera label or the serial number on the

package box label to open a browser management session with the Network Camera.

5. A browser session with the

Network Camera should prompt

as shown below.

6. You should be able to see live

video from your camera. You

may also install the 32-chan-

nel recording software from the

software CD in a deployment

consisting of multiple cam-

eras. For its installation details,

please refer to its related docu-

ments.

EN - 6

WPS

1. Make sure your AP (Access Point) and Operating System support WPS (Wi-Fi Protected

Setup) functions. WPS enables easy setup with compatible APs.

2. Disconnect your LAN cable, and connect the power cord.

3. Wait for 1 minute for the camera to boot up. Press the WPS button for 1 second. The

front panel LED should blink blue.

4. Press and hold down the WPS button on your AP (some router/AP

will have a virtual button on their management software instead).

Refer to your AP's documentation for details using its WPS

functions.

When WPS conguration is done, wireless connectivity will be established and the

security encryption, such as WEP or WPA-PSK, will be synchronized with the AP.

Use the IW2 utility to nd the camera. As for IP setting, the camera's use of DHCP or

static IP is determined by your conguration on the network camera via the web-based

conguration of rmware. The camera's default is DHCP.

NOTE:

WPS Button WPS Button

Wireless AP

1. It is strongly recommended to apply WPA2/AES encryption for access security.

2. WPS may not work if your AP is congured with a "hidden" SSID.

3. If no WPS-enabled AP is detected, and if the camera still can not detect an AP after 2

minutes, the wireless setup will be cancelled. If WPS conguration should fail, wireless

conguration will be cleared. You can then re-try the process above or use a wired

connection to establish a web console and manually congure the wireless settings.

4. If a camera is assigned with a xed IP outside the AP's network segment, wireless setup

will fail.

5. A wired connection always has a higher priority, and hence wireless setup will not take

effect when the RJ45 LAN port is connected.

Wireless Connection: Using the WPS Button

EN - 7

English

1. In addition to the use of WPS function, you can also use a wired connection to manually

set up your wireless conguration.

2. Enter the Conguration > Wireless > WLAN page. Key in the same wireless settings

as those on your router/AP (SSID, Encryption type, and Pre-shared key).

Wireless Connection: Manual Conguration

3. When done, click the Save button, disconnect the Ethernet cable and then reboot the

camera (by disconnect and then connect the power cord). The camera should then be

connected over the wireless network. If successfully congured, the camera LED should

turn Green after 1 minute. If the camera LED does not turn Green within 2 minutes,

check your wireless conguration for errors.

Quick Installation Guide

VIVOTEK INC.

6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.

|T:+886-2-82455282|F:+886-2-82455532|E:[email protected]

VIVOTEK USA, INC.

2050 Ringwood Avenue, San Jose, CA 95131

|T: 408-773-8686|F: 408-773-8298|E: [email protected]

IP8130/8131: 1MP • Compact Size

IP8130W/8131W: 1MP • 802.11n WLAN • WPS

All specications are subject to change without notice.

P/N:625021700G Rev. 1.0

IP8130/8131

Cube

Network Camera

English 繁中日本語 Español Português

簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska

Dansk

Nederlands

Indonesia

IP8130W/8131W

Otros manuales para IP8130

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vivotek

Vivotek

Vivotek FD8161 Manual de usuario

Vivotek

Vivotek IP7153 Manual de usuario

Vivotek

Vivotek IP8362 Manual de usuario

Vivotek

Vivotek PZ8111 Manual de usuario

Vivotek

Vivotek FD8377-HTV Manual de usuario

Vivotek

Vivotek IB9367-EHT-v2 Manual de usuario

Vivotek

Vivotek Supreme MD8531H Manual de usuario

Vivotek

Vivotek IP9167-HT Manual de usuario

Vivotek

Vivotek IP8173H Manual de usuario

Vivotek

Vivotek IP8371E Manual de usuario

Vivotek

Vivotek NetworKam IP3111 Manual de usuario

Vivotek

Vivotek IP3133 Manual de usuario

Vivotek

Vivotek IP6117 Manual de usuario

Vivotek

Vivotek NetworKam IP2111 Manual de usuario

Vivotek

Vivotek FD8367A-V Manual de usuario

Vivotek

Vivotek FD9367-HTV Manual de usuario

Vivotek

Vivotek VC8201 Manual de usuario

Vivotek

Vivotek FE9382-EHV-v2 Manual de usuario

Vivotek

Vivotek MD8563-EHF4 Manual de usuario

Vivotek

Vivotek FD8163 Manual de usuario

Vivotek

Vivotek FD8166A-N Manual de usuario

Vivotek

Vivotek MD8562 Manual de usuario

Vivotek

Vivotek FE9192-H Manual de usuario

Vivotek

Vivotek Supreme SD83xxE Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario