Vivo STAND-V106A Manual de usuario

Hex Monitor Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v106a

[email protected]om www.vivo-us.com 1-800-371-5654

SKU: STAND-V106A

PACKAGE CONTENTS

a (x1)

Pole

b1 (x1)

Clamp

c(x1)

Decorative

Cover

NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED

d1 (x2)

Monitor Arm

d2 (x4)

Monitor Arm

f (x8)

Plastic Pad

g (x4)

M10x47

h (x3)

Clamp Brace

Bolt

q (x24)

M4x30

r (x24)

M4 Spacer

i (x2)

M10x15

j(x4)

M8x10

s (x2)

Spare Cap

t (x1)

Allen Wrench

u(x1)

Wrench

v1 (x4)

VESA Plate

k(x1)

M10 Bolt

l (x1)

Support Plate

m (x1)

M10 Washer

n (x1)

Spring Washer

o (x1)

Foam Pad

p (x24)

M4x12

b2 (x1)

Clamp Brace

e (x8)

Arm Cover

w1 (x4)

Nut

w2 (x2)

M4x6

x (x8)

Wire Clip

v2 (x2)

VESA Plate

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

22 lbs

(10 kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PER ARM

TOOLS NEEDED

Phillips

Screwdriver Drill

ASSEMBLY STEPS

STEP 1

OPTION A: Weighted Base Installation

Attach clamp brace (b2) to pole (a) with clamp brace bolts (h). Attach clamp (b1) to clamp brace at

desired height using M10x15 bolts (i) with Allen wrench (t). Tighten clamp to desk and slide decorative

cover (c) into place.

OPTION B: Existing Grommet Base Installation

Apply foam pad (o) to base of pole (a). Mount pole to grommet hole in desk using M10 bolt (k), spring

washer (n), M10 washer (m) and support plate (l). Tighten with wrench (u) and slide decorative cover

b1 eye bolt

Figure 3 Figure 4

STEP 2

Place plastic pads (f) onto ends of monitor arms (d2), insert into arms (d1), and secure using M10x47

bolts (g) with Allen wrench (t). Press monitor arm covers (e) onto joints.

2.1

2.2

2.3

STEP 1 (Continued)

OPTION C: Self-Drilled Grommet Base Installation

Drill a 3/8” (10mm) diameter hole at desired location. Apply foam pad (o) to base of pole (a). Mount

pole to grommet hole in desk using M10 bolt (k), spring washer (n), M10 washer (m) and support

plate (l). Tighten with wrench (u) and slide decorative cover (c) into place.

d1,d2

STEP 4

4A: Side VESA Plates

For monitors with flat back attach VESA plates (v1) with thumb screws (p). For monitors with curved

back attach VESA plates (v1) with screws (q) and spacers (r). Screws need only to be finger-tight.

4B: Center VESA Plates

For monitors with flat back attach VESA plates (v2) with thumb screws (p). For monitors with curved

back attach VESA plates (v2) with screws (q) and spacers (r). Screws need only to be finger-tight.

STEP 3

Install wire clips (x) on arms (d1,d2).

Install arms on pole (a) at desired height

using M8x10 bolts (j) with Allen wrench

(t), making sure wire clips are facing

down.

5B: Center VESA Plates

Slide monitor onto the head of arm (d2) as shown in the diagram. Secure with screw (w2). Slide top

monitor onto mount in same fashion.

STEP 6

Adjust Tilt Angle of Monitors. Remove plastic cover and use wrench (u) to tighten the nut if the tilt

angle cannot be fixed. Fasten the grub screws on the center monitors to fix the tilt angle using Allen

wrench (t).

grub

screw

Fix the tilt angle

Pry off the

plastic cover

d1,d2

STEP 5

5A: Side VESA Plates

Slide monitor onto the head of arm (d2) as shown in the diagram. Secure with nut (w1).

d1,d2

STEP 8

To adjust swivel joint tension, remove the monitor arm cover (e) and turn the bolt underneath with

the Allen key (t).

STEP 9

Use wire clips (x) to help manage wires.

STEP 7

Adjust the height of Center Monitors: Turn the bolt counter-clockwise to lower the center monitors.

Turn the bolt clockwise to raise the center monitors. Use allen wrench (t). Adjust the height of the

Side Monitors: Remove nut (w1) and turn the bolt counter-clockwise to raise the monitor. Use allen

wrench (t).

Last Updated: 08/16/2019

If any parts are received damaged or defective, please contact us. We are happy to

replace parts to ensure you have a fully functioning product.

For more VIVO products, check out our website at:

www.vivo-us.com.

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

[email protected]om www.vivo-us.com 1-800-371-5654

Tabla de contenidos

Otros manuales de Rack y soporte de Vivo

Vivo

Vivo MOUNT-KB05W Manual de usuario

Vivo

Vivo MOUNT-MSIG24 Manual de usuario

Vivo

Vivo STAND-V101C Manual de usuario

Vivo

Vivo MOUNT-ALL02 Manual de usuario

Vivo

Vivo STAND-V100H Manual de usuario

Vivo

Vivo STAND-SHELF40B Manual de usuario

Vivo

Vivo STAND-V100G Manual de usuario

Vivo

Vivo MOUNT-KB05T Manual de usuario

Vivo

Vivo STAND-V100W Manual de usuario

Vivo

Vivo MOUNT-SONOS1 Manual de usuario

Vivo

Vivo STAND-V011 Manual de usuario

Vivo

Vivo MOUNT-VW01M Manual de usuario

Vivo

Vivo PP-DK12B Manual de usuario

Vivo

Vivo MOUNT-XSXU1 Manual de usuario

Vivo

Vivo MOUNT-PC06E Manual de usuario

Vivo

Vivo STAND-V001O Manual de usuario

Vivo

Vivo MOUNT-TS32B Manual de usuario

Vivo

Vivo MOUNT-VW090F Manual de usuario

Vivo

Vivo STAND-V002O Manual de usuario

Vivo

Vivo DESK-V103E Manual de usuario

Vivo

Vivo STAND-V002LW Manual de usuario

Vivo

Vivo STAND-V002F Manual de usuario

Vivo

Vivo STAND-V012L Manual de usuario

Vivo

Vivo STAND-V002P Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario