Vitek VTC-IRM40-2812 Manual de usuario

FEATURES:

• 1/2.8” Sony® STARVIS 2.1 MegaPixel CMOS Sensor

• 2.1 MegaPixel with Full 1080p/720p HD/EX-SDI 1.0, 2.0 / TVI / AHD / CVI

/ CVBS Output

• Advanced Starlight Technology Offers Dramatically Higher Sensitivity to Light

Producing Color Images in Very Dark & Night Scenes

• MegaPiel IR Corrected 2.8~12mm or 5~50mm Motorized Varifocal Lens with

1 click focus for easy Configuration

• 40 Dynamic Infrared LEDs at 850nm enable viewing in total darkness up to

150 feet

• Dual Glass Compartments to Eliminate IR Reflection

• 3D-DNR Digital Noise Reduction

• True Day/Night by ICR - Dual Filter Switch

• Fully programmable True WDR (Dual Scan)

• ROI (Region of Interest) WDR achieves superior exposure compensation

specifically in exact areas of interest while reducing HDD storage space

• Secondary Video Output & OSD Control Joystick are accessible inside a

gasket sealed removable side panel

• Advanced OSD Functions: Motion Detection, Privacy Mask, Defog, Sens-

up(~x32), Sharpness, Mirror/Flip, BLC/HLC, Deblur, Anti-Saturation, Title

Set, D-WDR

• 3-Axis mount with Simple One Turn Positioning Lock for Ease of Installation

• IP-68 Rated Water Resistance

• 12VDC / 24VAC Dual Voltage Operation

VTC-IRM40

Premium 2.1 Megapixel Indoor/

Outdoor 6-in-1 HD/EX-SDI / TVI / AHD

/ CVI / CVBS Motorized Varifocal Bullet

Camera with IR LED Illumination

VITEK

Safety Precaution

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

To prevent electric shocks and risk of fire hazards, do NOT use other than

specific power source.

The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

the users own expense.

Caution :

Any changes or modifications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user's authority

to operate the equipment.

Main power quality should be that of a typical commercial environment. If the user

of the model requires continued operation during power main interruption, it is

recommended that the model be powered from an uninterruptible power supply

(UPS).

2 3

Safety Precaution

NOTICE

The image used in this instruction manual are processed to help comprehension

and may differ from actual video of the camera.

Avoid installing areas where has shock or vibration which results in the problems.

Pay attention to safety when running the connection cable and observe that the cable

is not subjected to heavy loads, kinks or damage and no moisture can get in.

The warranty becomes void if repairs are undertaken by unauthorized persons.

Maintenance and repair have to be carried out only by authorized service centers.

Use only a mild detergent to clean the housing.

The camera should never be operated beyond the technical specifications.

This can lead to damage and void the warranty.

The camera should never be operated in water.

Contents

Safety Precaution

p.02~03

Contents

p.04

Composition

p.05

Dimensions

p.05

Installation Instructions

p.06~09

p.10~26

Operating Instructions

p.27

Specifications

4 5

Composition

Dimensions

Video Sub-out

Cable (1pc)

Mounting

Template

Operating

Instruction

Torque Wrench:

3mm (1pc)

Camera

Easy

Bracket

Mounting Screw:

4 x 30mm (4pcs)

Plastic Anchor:

6 x 30mm (4pcs)

Assembly Screw:

4 x 15mm (4pcs)

3.15”

3.31”

3.39”

4.35”

10.11”

3.94”

4.37”

3.53”

Part Names

■Adjustment of viewing angle with a bracket

• Extreme care should be taken NOT to

scratch the window in front of lens.

• Care should be taken that the cable is

not damaged, kinked or exposed in

hazardous areas.

• Do not expose the camera directly to a

strong light source such as the sun or

spotlight.

CAUTION

Power/Video

Cable

Sunshield

Sunshield Bold

Easy

Bracket

OSD Setup

Control Cover

Bracket

Lock/Unlock

Screw

Torque

wrench

Lock/Unlock

Screw

6 7

Installation Instructions

1. Locate the mounting template at the installation position and drill the ceiling or

wall if needed. ( *The easy bracket can not be installed on the ceiling)

2. Place the easy bracket on pre-drilled position and attach it using mounting

screws (4x30mm). Skip this step when an easy bracket is not installed.

3. Route the Power cable to the connecting place.

Hook up the camera bracket with the easy bracket as illustrated below.

4. Attach the camera bracket using assembly screws (4x15mm).

5. Set the camera’s viewing angle.

6. Put the sunshield onto the camera unit and tighten the sunshield-bolts.

Mounting Screw

: 4x30mm

Plastic Anchor

: 6x30mm

Torque Wrench

REAR VIEW

Cable exit

Assembly Screw

: 4x15mm

Installation Instructions

Pan & Tilt adjustments

1) Pan limit:

Pan is limited to +/- 90°.

3) Inclination limit

(Horizontal image alignment):

Inclination limited to +/-90° max.

2) Tilt limit:

Tilt is limited to 0°(2°) min ~ 90° max.

for wall(ceiling) installation respectively

with reference to the wall(ceiling) when

the inclination of camera module is 0°,

that is, the image is aligned horizontally.

90° 90°

• Unlock the screw on the camera bracket through using the torque wrench supplied

• Set the camera’s viewing angle then lock the screw on the bracket.

88°90°

±90°

•on the wall •on the ceiling

8 9

Installtion Instructions

Installation Instructions

• Make sure power is removed before the installation.

• Follow the order for applying power:

Connect the power leads to the camera (observe polarity for DC power) then

plug-in power. This will avoid damage to the camera from power surges and

improper reseting .

Power Supply Connections

Camera can work with either 12VDC or 24VAC, dual voltage power. Primary

and secondary grounds are completely isolated to avoid the possible ground-loop

problems.

※SDI OUTPUT

(Yellow)

ANALOG OUTPUT

(Black)

POWER

(AC24V/DC12V)

▪ AC(-) :

AC24V/GND

▪AC(+) :

AC24V/DC12V

(+)

(-)

※Please use the cable as provided with camera. If camera cable is cut

and re-wired, the transmission distance of video can be reduced.

Especially SDI cable should not be cut because it requires detailed

wiring and affects the transmission distance.

Operating Instructions

Setup menu can be accessed and controlled by OSD control joystick on

the side of the camera. Five commands are available with the joy stick.

The design of OSD could be different according to the Model.

Description of the joystick operation

1) SET (●) : Access to the menu or enter the setting.

2) UP/DOWN (▲/▼) : Choose the desired sub-menu and to move the cursor up or down.

3) LEFT/RIGHT (◄/►) : Set up the value of the selected menu.

Used to adjust the desired menu selection and to move the cursor left or right.

Using OSD Controller

4) ‘ ’denotes the long press down straightly for about 2 seconds

Video Sub-out

Connector

OSD Control Joy Stick

SUB-OUT

ZOOM

Cover Open

Description of the Motorized ZOOM&FOCUS* adjustment

1) ▲: Zoom In

2) ▼ : Zoom Out

3) ◄: Focus Near

4) ► : Focus Far

(*) Works only when OSD Menu is inactive.

ANALOG OUT0 should be set to TVI MODE, AHD MODE or CVI MODE

to get CVBS video in sub-out. If it is set to CVBS, there is no CVBS video

in sub-out port. (SYSTEM> OUTPUT> ANALOG OUTPUT0)

If CVBS video is enabled through ANALOG OUT or Sub-out port, WDR

and 3D-NR functions are disabled in all video outputs.

It should be considered when installer adjusts the video with installation

monitor via CVBS video signal.

10 11

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vitek

Vitek

Vitek VT-PTZ12W Manual

Vitek

Vitek VTC-IRA40/3516 Manual de usuario

Vitek

Vitek TRANSCENDENT VTC-TNB4LPRN Manual de usuario

Vitek

Vitek VTC-TNB8RFA4-2 Manual de usuario

Vitek

Vitek Transcendent VTC-TNT8RFS Manual de usuario

Vitek

Vitek VTD-IR2811DN Manual de usuario

Vitek

Vitek VTC-C770/WDR Manual de usuario

Vitek

Vitek Transcendent VTC-THB5RM Manual de usuario

Vitek

Vitek VTC-LED307BB Manual de usuario

Vitek

Vitek VTC-TNB4RMAD Manual de usuario

Vitek

Vitek VTC-B301 Manual de usuario

Vitek

Vitek VTC-BHOCRAZ Manual de usuario

Vitek

Vitek VTC-C01 Manual de usuario

Vitek

Vitek Transcendent Series Manual de usuario

Vitek

Vitek TRANSCENDENT VT-SMKC2T Manual de usuario

Vitek

Vitek Transcendent VTD-TNMD4RFS-2 Manual de usuario

Vitek

Vitek Alpha Series Manual de usuario

Vitek

Vitek VT-PIRC1 Manual de usuario

Vitek

Vitek VTD-C410 Manual de usuario

Vitek

Vitek Transcendent VTD-TND4RMA3B Manual de usuario

Vitek

Vitek VIRTUOSO Manual de usuario

Vitek

Vitek Alpha VTD-C14A Manual de usuario

Vitek

Vitek VTC-IRLED24A Manual de usuario

Vitek

Vitek Transcendent VTC-TNB8RFS-2 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario