Vision Express S5 Manual de usuario

Vision Express Engraver S5

Installation Guide

Revised: 11/5/2018Part number 12-1084-01

mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the

written permission of the publisher.

Products that are referred to in this document maybe either trademarks and/or registered trademarks of the

respective owners. The publisher and the author make no claim to these trademarks.

While everyprecaution has been taken in the preparation of this document, the publisher and the author assume no

responsibilityfor errors or omissions, or for damages resulting from the use of information contained in this

document or from the use of programs and source code that mayaccompanyit. In no event shall the publisher and

the author be liable for anyloss of profit or anyother commercial damage caused or alleged to have been caused

directlyor indirectlybythis document.

Revised: 11/5/2018

Vision Express Engraver S5 Installation

Guide

3Contents

Table of Contents

Part I Introduction 4

................................................................................................................................... 51 Computer Requirements

................................................................................................................................... 62 General Electrical and Facility Requirements

................................................................................................................................... 63 Vision ExpressEngraver Installation Layout

Part II Vision Software Installation 7

Part III Machine Setup 18

................................................................................................................................... 201 Direct Connection to Computer

................................................................................................................................... 262 Network Connection

Vision Express Engraver S5 Installation Guide4

1 Introduction

This guide contains information to prepare the new owner of a Vision Express for the proper installation of

their machine. It is the customer's responsibility to read through this guide and make sure the work area,

electrical and computer requirements are met. If for any reason, there are questions about these

requirements, please call your Vision representative as soon as possible.

In the following sections, the complete machine and Vision software installation will be outlined.

Please call your distributor or the service department at Vision for assistance if you have any questions

with this procedure.

FOR MORE DETAILED INFORMATION, PLEASE REFER TO THE USER GUIDE FOR YOUR MACHINE

INSTALLED WITH THE VISION SOFTWARE. USER GUIDES ARE ALSO AVAILABLE ONLINE AT

http://www.visionengravers.com/support/vision-engraver-manuals.html

Important Note:

The Vision software is available in two versions; one with a dongle, and one

that is "dongle-less" and is loaded on to a USB Memory stick. If your machine

was delivered with, or you currently have the white/blue or orange software

dongle, DO NOT LOSE IT!

The Vision software will NOT run without the dongle plugged into the computer.

Introduction 5

1.1 Computer Requirements

Minimum System

Requirements:

CPU:

Dual Core (2.0GHz or higher)

Hard Drive:

750 GB free space

RAM:

1GB + OS Requirements

Operating System:

Windows 10 (32/64 bit)

Windows 8 (32/64 bit)

Windows 7 SP.1 (32/64 bit) ***Requires Service Pack 1

Ports:

USB port for security dongle

Local or network Ethernet port to connect machine

Suggested System

Requirements

CPU:

Core i3 (or faster)

Hard Drive:

1 TB (or more)

RAM::

4GB + OS Requirements

Operating System:

Windows 10 (32/64 bit)

Windows 8 (32/64 bit)

Windows 7 SP.1 (32/64 bit) ***Requires Service Pack 1

Ports

USB port for security dongle

Local or network Ethernet port to connect machine

Vision Express Engraver S5 Installation Guide6

1.2 General Electrical and Facility Requirements

Machine Model

Requirements

Express

One 110 VAC 15 Amp or One

220 VAC 10 Amp Single Phase

Optional Equipment

Engraving Vacuum Chip Removal System

One 110 VAC 15 Amp

NOTE: In addition to the above requirements, a standard outlet is required for the

computer.

1.3 Vision Express Engraver Installation Layout

Vision Express Engraver Installation Layout

Introduction 7

2 Vision Software Installation

Insert the Vision USB dongle into the USB port on the computer. Navigate to the Devices and Drives

area on your PC. Double click on the Vision icon to open the files on the USB dongle.

Select the Start or Start.exe file to begin.

Click on the Install Vision Software button.

Vision Express Engraver S5 Installation Guide8

The Vision S5 Software Wizard will guide you through the process of installing the software. Press Next

to continue.

Press Install to continue

Vision Software Installation 9

Setup wizard will install the program.

Select Finish to continue the software installation.

Choose your preferred language and click ok.

Vision Express Engraver S5 Installation Guide10

The Vision 10 Setup Screen will appear. Press Next.

After accepting the license agreement, click on the Next button.

Otros manuales para Express S5

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Grabador de Vision

Vision

Vision VE-810 Manual de usuario

Vision

Vision Cylindrical Manual de usuario

Vision

Vision Multi Axis Manual de usuario

Vision

Vision PHOENIX TABLE Manual de usuario

Vision

Vision MAX Pro Manual de usuario

Vision

Vision 16 Series Manual de usuario

Vision

Vision Phoenix 1212 Manual de usuario

Vision

Vision VE810 4 Series Manual de usuario

Vision

Vision SP Series Manual de usuario

Vision

Vision 5 Series Manual de usuario

Vision

Vision VE810 S5 Manual de usuario

Vision

Vision MAX Pro Manual de usuario

Vision

Vision 5 Series Manual de usuario

Vision

Vision Phoenix 1212 S5 Manual de usuario

Vision

Vision 1624R Manual de usuario

Vision

Vision Express S5 Manual de usuario

Vision

Vision MaxPro Manual de usuario

Vision

Vision 1612 Manual de usuario

Manuales populares de Grabador de otras marcas

COMGROW

COMGROW COMGO Z1 Manual de usuario

BAUKER

BAUKER EG013 Manual de usuario

GRAVOGRAPH

GRAVOGRAPH LS900 XP Instrucciones de funcionamiento

iMARC

iMARC VET TAG Engraver Manual de usuario

Epilog Laser

Epilog Laser Edge 12 Manual de usuario

Dremel

Dremel 3000 Operating/s Manual de usuario

iMARC

iMARC Pet Tag Engraver Manual de usuario

PT W50036 Manual de usuario

Omtech

Omtech USB3020A Manual de usuario

Ortur

Ortur Laser Master 2 Manual de usuario

Epilog Laser

Epilog Laser FiberMark Manual de usuario

Omtech

Omtech POLAR 350 Manual de usuario

SCULPFUN

SCULPFUN S6 Manual de usuario

Redsail

Redsail M500 Guía de configuración rápida

Dremel

Dremel 290 Instrucciones de montaje

Epilog Laser

Epilog Laser Edge 12 Manual de usuario

SFX

SFX SFX-GS Manual de usuario

Dongguan Ortur

Dongguan Ortur Laser Master 2 Manual de usuario