Vision Engraving & Routing Systems VE-810 Manual de usuario

VE-810 Engraver

Operations Manual

Vision Engraving & Routing Systems

17621 N. Black Canyon Hwy.

Phoenix, AZ 85023

www.visionengravers.com



1999 Vision Computerized Engraving & Routing Systems

(A Division of Western Engravers Supply, Inc.)

This publication is protected by copyright, and all rights are reserved. No part of this manual may be reproduced or

transmitted by any means or in any form, without prior written consent from Vision.

Limits of Liability/Disclaimer of Warranty for this Equipment Manual

The information contained within this manual has been carefully checked and is believed to be accurate, however, Vision

makes no representations or warranties for this manual, and assumes no responsibility for inaccuracies, errors, or

omissions that may be contained within this manual. In no event shall Vision be liable for any loss of profit including

(but not limited to) direct, indirect, special, incidental, consequential, or other damages resulting from any defect or

omission in this manual, even if previously advised of the possibility of such damages.

In the interest of continued product development, Vision reserves the right to make improvements to this manual and the

products it describes at any time, without notice or obligation.

Table of Contents iii

Table of Contents

CHAPTER 1 - BEFORE YOU BEGIN.......................................................................................................................... 5

INTRODUCTION ................................................................................................................................................................5

SAFETY ............................................................................................................................................................................5

UNPACKING AND TAKING INVENTORY .............................................................................................................................6

MACHINE DESCRIPTION & TERMINOLOGY.......................................................................................................................7

CHAPTER 2 - INSTALLATION ................................................................................................................................. 11

SOFTWARE INSTALLATION .............................................................................................................................................11

CONNECTING THE TABLE ...............................................................................................................................................17

CONFIGURING THE COMPUTER .......................................................................................................................................19

CHAPTER 3 - OPERATIONS...................................................................................................................................... 21

THE FRONT PANEL.........................................................................................................................................................21

HOLDING DOWN MATERIAL ............................................................................................................................................24

DIAMOND DRAG ENGRAVING ........................................................................................................................................25

ROTARY ENGRAVING .....................................................................................................................................................27

BURNISH ENGRAVING ....................................................................................................................................................29

CHAPTER 4 - OPTIONAL ACCESSORIES.............................................................................................................. 33

CLAMPING DEVICES .......................................................................................................................................................33

VACUUM CHIP REMOVAL SYSTEM.................................................................................................................................40

CHAPTER 5 - MAINTENANCE ................................................................................................................................. 41

REMOVING CHIPS...........................................................................................................................................................41

LUBRICATION.................................................................................................................................................................42

CHANGING THE MOTOR BELT ........................................................................................................................................43

CHANGING THE MOTOR BRUSHES..................................................................................................................................47

CLEANING THE FAN FILTER............................................................................................................................................50

REPLACING THE EXTERNAL FUSES.................................................................................................................................51

REPLACING THE INTERNAL FUSE....................................................................................................................................52

CHAPTER 6 - TROUBLESHOOTING....................................................................................................................... 55

ENGRAVING PROBLEMS .................................................................................................................................................55

MECHANICAL PROBLEMS...............................................................................................................................................58

INDEX............................................................................................................................................................................. 61

iv VE810 Engraver Manual

Chapter 1 - Before You Begin 5

Chapter 1 - Before You Begin

Introduction

About This Manual

This manual is designed to provide you with information about your Vision VE-810

engraver, beginning with unpacking the machine and continuing through installation and

lifetime machine maintenance. This manual does not attempt to teach you how to

engrave, how to use a computer or how to use your engraving software. Some previous

knowledge of engraving terms and the engraving process is assumed. For information

on the Vision Engraving Software, see the Vision Engraving Software manual. For

more information on your individual computer system, see your computer’s user manual or

contact your computer distributor.

Safety

Safety Precautions for the VE-810 Engraver

Ø Keep hands clear of the bottom of the spindle during operation.

Ø Always stop the machine before making any adjustments.

Ø Do not operate the machine with the covers removed.

Ø Wear safety glasses when cutting any materials that emit chips.

Ø Use extreme caution when inserting or removing cutters.

Ø Before any servicing, disconnect the power cord.

Ø To avoid electric shock or equipment damage, ensure that the control unit is connected

to the appropriate electrical source as noted in the installation procedures.

Ø Never operate the equipment with damaged or frayed power cords, loose connections,

or exposed extension cords where someone can step on the cord and create a tripping

hazard.

Ø Be sure to hold the plug, not the cord, when disconnecting the controller from an

electrical socket or power source.

6 VE810 Engraver Manual

Ø Place the machine in a location with low humidity and a minimum of dust. Avoid

placing the equipment in direct sunlight or in locations with excessive heat. Follow the

maintenance instructions for proper cleaning of the controller air filter.

Ø If your machine does not operate properly; in particular, if there are any unusual

sounds or smells coming from it, immediately unplug it and contact a service technician

or your local distributor.

Ø Unplug the machine when it is going to be left unused for an extended period of time.

Unpacking and Taking Inventory

The VE-810 engraving system has been shipped in one carton, unless other accessories

have been ordered with the machine that will not fit in the box. Examine the condition of

the box for external damage. In the event of apparent external damage, notify your

shipping carrier upon receipt, and call your sales representative or Vision immediately.

Note: The shipping container is considered reusable and should be stored for use in the

event of service need or upgrade.

Step1:

Open the foam packed shipping carton. In the top of the carton will be a cardboard box

with all of the machine accessories (including this manual). Open the accessory box and

the following items should be included:

ü 1 VE-810 Machine

ü 1 VE-810 Warranty Card

ü 1 Vision Software Manual

ü 1 Vision Software CD

ü 1 Vision Keyboard Template

ü 1 Vision Font Catalog

ü 1 Operations Manual

ü 1 Mouse Pad

ü 2 Spare 5 Amp Fuses

ü 1 Spare 1 Amp Fuse

ü 1 Power Cord

ü 1 Interface Cable

ü 1 Interface Cable Adapter (25 pin to 9 pin)

ü 1 Extra 14“ Motor Belt

ü 1 Allen Wrench Set

ü 1 Cutter Wrench

Check to see that all of the items are included. Should any of the contents be missing,

damaged, or of the incorrect type, please call your sales representative or Vision

immediately.

Step 2:

Chapter 1 - Before You Begin 7

Prepare a clean, level surface to put the engraving machine on. Carefully lift the machine

out of the carton and place it on the table.

Step 3:

After unpacking the machine, make sure that you SAVE THE CARTON, FOAM PACK and

ANY OTHER BOXES. They can be reused in the event the system must be transported

to another location or returned for service. Improper packaging for shipment can damage

the table or controller and may void the warranty.

Machine Description & Terminology

This chapter briefly describes the major components of the VE-810 table. Figure 1.1

shows a labeled drawing of the VE-810 Engraver. This chapter will help you identify the

parts of your table discussed elsewhere in the manual.

*Optional equipment such as accessory vises, clamps, fixtures or vacuum systems

may have been included with your system. For information regarding this

equipment, see the individual instructions for these options. For descriptions of

controllers, computers, and software used in your system, see the manuals from the

manufacturers of these units.

TABLE SPECIFICATIONS:

Z-Axis Clearance: 1 inch (25.4 mm)

(Definition: the distance between the bottom of the spindle and the work surface)

Z-Axis Stroke: 1 inch (25.4 mm)

(Definition: the travel distance of the Z-axis mechanism or spindle)

Table Resolution: .001 inch

(Definition: the smallest controlled motion the table is capable of)

Engraving Area: 8” x 10“ (203.2 mm x 254 mm)

Overall Dimensions: 14 1/2” Tall x 19“ Wide x 22” Deep

368 mm Tall x 483 mm Wide x 559 mm Deep

Table Top: Removable T-Slot

Shipping Weight: 65 lbs.

Shipping Dimensions: 27“ x 22” x 19“

DEFINITION OF TERMS (see Figure 1.1)

1. X-Axis Leadscrew - The screw that drives the left to right motion of the machine.

2. X-Axis Linear Rails - The 1/2” round rails that the carriage assembly rides on.

8 VE810 Engraver Manual

3. Y-Axis Linear Rails - The 1/2“ round rails that the t-slot table rides on.

4. Y-Axis Leadscrew - The screw that drives the front to back motion of the machine.

5. T-Slot Table - Also referred to as the work surface, this aluminum bed supported by the

Y-Axis linear rails allows placement of the engraving material or special clamps and

fixtures. The slots in the table are shaped with an upside-down T, with the bottom of the T

being a single-line slot across the top of the table. The slots are used to hold various

accessory holders, clamps, and jigs.

6. Front Panel - This is the area in which you control the table movement. You can start,

stop, pause, cancel a job and set the spindle surface. Also, you can control the speed at

which the table moves and the spindle RPM.

7. Quick Lock Vise - This is the clamp assembly that is included with the VE-810

Engraver that allows you to lock your material on the T-Slot table.

8. Table Home Position - This is the place on the T-Slot table where you position your

engraving material. All work is referenced from this position.

9. Spindle - This is the part where the engraving cutters are inserted and adjusted for

depth of cut.

10. Spindle Motor Pulley - This is where the motor belt runs from. It runs from the

spindle motor pulley to the spindle causing the spindle to turn. (The spindle motor pulley is

hidden by the cover. In order to see it, you must remove the covers).

(Figure 1.1) The VE-810 top view

Chapter 1 - Before You Begin 9

1. X-Axis Leadscrew 2. X-Axis Linear Rails

3. Y-Axis Linear Rails

4. Y-Axis Leadscrew

5. T-Slot Table

8. Table Home Position

6. Front Panel

9. Spindle

10. Spindle Motor Pulley

7. Quick Lock Vise

11. Spindle Up/Down Knob - This knob raises and lowers the spindle when the power is

off. You will see it turn as the spindle moves up and down while engraving.

12. Down Pressure Spring Adjust - This knob adjusts the amount of pressure that the

spindle applies on the material being engraved. Looking down from the top, turning it

clockwise will increase pressure and turning it counter-clockwise will decrease pressure.

13. Spindle Pulley - This is the top part of the spindle where the motor belt rides.

14. Spindle Micrometer - This is the part of the spindle that you adjust to set the depth of

engraving. Turning it to the right will cause the engraving to be deeper.

15. Spindle Nose Cone - This is the part of the spindle that rides on the material while

engraving. The cutter protrudes from the bottom of the nose cone creating your depth of

cut.

(Figure 1.2) The VE-810 carriage view

10 VE810 Engraver Manual

11.

pindle Up/Down Knob

12. Down Pressure Spring Adjust

13. Spindle Pulley

14. Spindle Micrometer

15. Spindle Nose Cone

Tabla de contenidos

Otros manuales de Grabador de Vision Engraving & Routing Systems

Vision Engraving & Routing Systems

Vision Engraving & Routing Systems Express Manual de usuario

Manuales populares de Grabador de otras marcas

COMGROW

COMGROW COMGO Z1 Manual de usuario

BAUKER

BAUKER EG013 Manual de usuario

GRAVOGRAPH

GRAVOGRAPH LS900 XP Instrucciones de funcionamiento

iMARC

iMARC VET TAG Engraver Manual de usuario

Epilog Laser

Epilog Laser Edge 12 Manual de usuario

Dremel

Dremel 3000 Operating/s Manual de usuario

iMARC

iMARC Pet Tag Engraver Manual de usuario

PT W50036 Manual de usuario

Omtech

Omtech USB3020A Manual de usuario

Ortur

Ortur Laser Master 2 Manual de usuario

Epilog Laser

Epilog Laser FiberMark Manual de usuario

Vision

Vision VE-810 Manual de usuario

Omtech

Omtech POLAR 350 Manual de usuario

Vision

Vision Cylindrical Manual de usuario

SCULPFUN

SCULPFUN S6 Manual de usuario

Redsail

Redsail M500 Guía de configuración rápida

Dremel

Dremel 290 Instrucciones de montaje

Vision

Vision MaxPro Manual de usuario