Viessmann Vitocom 100 Instrucciones de funcionamiento
Installation and service
instructions
for contractors
VIESMANN
Vitocom 100
Type GSM
Remote monitoring and remote control of heating systems
For applicability, see the last page
VITOCOM 100
5606 565 GB 10/2011 Please keep safe.
2
Please follow these safety instructions closely to prevent accidents and mate-
rial losses.
Safety instructions explained
Danger
This symbol warns against the
risk of injury.
!Please note
This symbol warns against the
risk of material losses and envi-
ronmental pollution.
Note
Details identified by the word "Note" con-
tain additional information.
Target group
These instructions are exclusively
designed for qualified contractors.
■ Work on electrical equipment must
only be carried out by a qualified elec-
trician.
■ The system must be commissioned by
the system installer or a qualified per-
son authorised by the installer.
Regulations
Observe the following when working on
this system:
■ National installation requirements
■ Legal instructions regarding the pre-
vention of accidents
■ Legal instructions regarding environ-
mental protection
■ The Code of Practice of relevant trade
associations
■ All current safety regulations as
defined by DIN, EN, DVGW, VDE and
all locally applicable standards
aÖNORM, EN and ÖVE
cSEV, SUVA, SVTI and SWKI
Working on the system
■ Isolate the system from the power sup-
ply (e.g. by removing the separate fuse
or by means of a mains isolator) and
check that it is no longer 'live'.
■ Safeguard the system against unau-
thorised reconnection.
!Please note
Electronic assemblies can be
damaged by electrostatic dis-
charges.
Before beginning work, earthed
objects, such as heating or water
pipes, must be touched to dissi-
pate any static charge.
Repair work
!Please note
Repairing components that fulfil a
safety function can compromise
the safe operation of your sys-
tem.
Replace faulty components only
with original Viessmann spare
parts.
Safety instructions
Safety instructions
5606 565 GB
3
Auxiliary components, spare and
wearing parts
!Please note
Spare and wearing parts that
have not been tested together
with the system can compromise
its function. Installing non-author-
ised components and making
non-approved modifications or
conversions can compromise
safety and may invalidate our
warranty.
For replacements, use only orig-
inal spare parts supplied or
approved by Viessmann.
Safety instructions
Safety instructions (cont.)
5606 565 GB
4
Installation instructions
Safety and liability.............................................................................................. 6
Preparing for installation
System requirements........................................................................................... 7
Vitocom 100 functions.......................................................................................... 8
Installation sequence
Installing the Vitocom 100.................................................................................... 9
Overview of electrical connections....................................................................... 10
Connecting the Vitocom 100................................................................................ 12
Digital input connections...................................................................................... 14
Power supply........................................................................................................ 16
Service instructions
Commissioning
Commissioning steps – Overview........................................................................ 18
Inserting the SIM card ......................................................................................... 18
Entering the SIM card PIN.................................................................................... 20
Sending the commissioning SMS to the Vitocom 100 ......................................... 21
Creating SMS templates in the mobile phone...................................................... 22
SMS commands
Notes on SMS commands.................................................................................... 23
Changing the access code................................................................................... 23
Language selection.............................................................................................. 24
Entering information text...................................................................................... 25
Entering a mobile phone number......................................................................... 25
Entering operating mode changeover.................................................................. 26
Entering SIM card credit (prepaid only)................................................................ 27
Entering the cost for sending one SMS (prepaid only)......................................... 28
Entering SIM card valid from date (prepaid only)................................................. 28
Re-starting the Vitocom 100 and selection resets................................................ 30
Scanning
Scanning current settings..................................................................................... 31
LED indications
LED descriptions.................................................................................................. 32
Reception quality (Field strength)......................................................................... 32
SMS transmission indication................................................................................ 32
Index
Index
5606 565 GB
5
Troubleshooting
Interpreting the LED flashing patterns.................................................................. 33
Fault messages.................................................................................................... 33
Specification....................................................................................................... 35
Certificates
Declaration of conformity...................................................................................... 36
Keyword index.................................................................................................... 37
Index
Index (cont.)
5606 565 GB
6
Danger
The Vitocom radio signals (from
communication via mobile
phone) may interfere particularly
with pacemakers, hearing aids
and defibrillators.
If you use any such equipment,
please avoid the immediate vicin-
ity of the operational Vitocom.
!Please note
The Vitocom only relays faults of
connected Vitotronic control units
and of the components connec-
ted to its configured inputs. For
technical details, see the installa-
tion and service instructions of
the appliances.
Conditions for fault messages:
■ The Vitotronic control units
and the Vitocom must be con-
figured correctly.
■ The Vitocom message paths
must be established.
■ The heating system and func-
tionality of the message facili-
ties must be checked at regular
intervals.
■ In order that messages can still
be transferred during a power
failure, we recommend using a
UPS (uninterruptible power
supply).
■ For further improvement of the
operational reliability of the
heating system, we recom-
mend allowing for supplemen-
tary measures, e.g. frost pro-
tection or monitoring for water
damage.
Liability
Viessmann accepts no liability for loss of
profit, unattained savings, or other direct
or indirect consequential losses resulting
from the use of the Vitocom or the soft-
ware, nor for losses resulting from inap-
propriate use.
The Viessmann General Terms and
Conditions apply; these are listed in the
relevant current Viessmann pricelist.
We accept no liability for SMS and e-mail
services provided by network operators.
The terms and conditions of the relevant
network operators therefore apply.
Safety and liability
Safety and liability
5606 565 GB
7
Heating system
■ For 1 heating system with Viessmann
heat source and Viessmann control
unit.
■ The control unit is connected to the
Vitocom 100 via the KM BUS.
■ Mains socket 230 V/50 Hz or optional
connection in accordance with safety
category II.
Mobile network
■ Adequate radio signal (field strength)
for the selected mobile network where
the Vitocom 100 is sited.
■ The SIM card must be enabled by the
mobile phone provider at the time of
commissioning.
SIM card requirements:
– SMS facility
– Bi-directional function (sending and
receiving)
Note
SIM cards approved for use with the
Vitocom 100:
■ T-Mobile (standard for Vitocom 100
with SIM card)
■ Vodafone
■ E-Plus
The SIM cards have been tested at a ref-
erence location. Perfect operation can-
not be guaranteed in some regions.
Message paths/Message targets
■ Mobile phone for receiving and send-
ing messages as SMS.
Up to two mobile phones can be speci-
fied as message recipients.
Important information regarding sys-
tem limitations
■At the time of publication of this
document the transmission range of
the Vitocom 100 has only been tes-
ted with the tested SIM cards (for
use with the Vitocom 100). The per-
fect function of the Vitocom 100 can
only be guaranteed with tested SIM
cards.
■ The SMS transmission is a service
provided by the mobile phone network
operator. We cannot accept liability for
the radio reception of the Vitocom 100
if changes are implemented by the
mobile phone operator.
■ The radio reception of the Vitocom 100
has not been tested with all types of
mobile phone. Although no restrictions
could be detected with any of the tes-
ted mobile phones, the perfect func-
tion of the Vitocom 100 cannot be
guaranteed for all available mobile
phones.
Preparing for installation
System requirements
5606 565 GB
Installation
8
Summary of functions
E
BC
A
D
AViessmann control unit
BKM BUS cable
CVitocom 100
DAerial (not extendible)
EMobile phone
Remote switching
The operating mode of the heating cir-
cuits connected to the control unit can be
switched over.
Note
Connect the control unit to the
Vitocom 100 via a KM BUS.
Remote scanning
The following settings of the Vitocom 100
can be scanned:
■ 2 mobile phone numbers that can be
notified in case of faults.
■ SIM card credit (prepaid).
■ SIM card current date and expiry (pre-
paid).
■ Cost of one SMS (stored value).
■ Information text for designating the
system and the digital input.
■ Selected language.
Remote monitoring
■ The Vitocom 100 monitors heating
systems with Viessmann control units
connected to the Vitocom 100 via KM
BUS.
Note
In a LON system, only that control unit
is monitored that is connected to the
Vitocom 100 via the KM BUS.
■ The Vitocom 100 monitors appliances/
devices connected to the digital input.
The following are automatically signalled
as SMS via the mobile phone network:
■ Faults.
■ Expiry of SIM card (prepaid).
■ Notification regarding resetting the
current date after a power failure.
Note
The dates "AKTDAT" and "ENDDAT"
only need to be entered with a prepaid
SIM card for monitoring the available
credit.
Preparing for installation
Vitocom 100 functions
5606 565 GB
9
Information on installation location:
■ Adequate strength of reception.
Note
Adequate strength of reception using
a mobile phone and a SIM card from
same mobile phone operator, see
page 32.
■ Maintain the max. cable length (total
length of all cable lengths of KM BUS
subscribers up to 50 m)
■ Power plug of the Vitocom 100 must
be easily accessible.
Install the aerial (not extendible) in a
favourable location:
■ To a suitable metal surface using the
magnet that is integrated in the aerial.
■ To a smooth, clean and dry surface
using the adhesive pad provided.
2. 3. 4x
1.
Installation sequence
Installing the Vitocom 100
5606 565 GB
Installation
10
Opening the enclosure
B
LOCK
OPEN
6
5
2
1
0
8
9
7
3
4
A F H KLD EC
MNOP
G
AKM BUS cable (plug aVG supplied)
BAerial cable (standard delivery)
CKM BUS terminals
DPlug-in connection to the wiring
chamber
ESIM card holder
FGSM modem
GPIN rotary selector
HPerforation for the strain relief
recess, digital input
KCable entry, digital input 230 V~ (for
additional appliance)
LPower cable
MGreen LED
NYellow LED
ORed LED
PPushbutton for setting the PIN
Opening the wiring chamber
Only for connecting an additional appli-
ance to the digital input and gaining
access to the mains terminals.
Installation sequence
Overview of electrical connections
5606 565 GB
Otros manuales para Vitocom 100
8
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Mando a distancia de Viessmann
Viessmann
Viessmann VITOTROL 300 RF Manual de usuario
Viessmann
Viessmann VITOTROL 200 RF Manual de usuario
Viessmann
Viessmann Vitotrol 300-B Instrucciones de funcionamiento
Viessmann
Viessmann VITOTROL 100-E Manual de usuario
Viessmann
Viessmann VITOTRONIC 200 Manual de usuario
Viessmann
Viessmann Vitotrol 200 Manual de usuario
Viessmann
Viessmann VITOTRONIC 200 Manual de instrucciones
Viessmann
Viessmann Vitotrol 300-E Manual de usuario
Viessmann
Viessmann VITOTROL 200 RF Guía rápida
Viessmann
Viessmann Vitocom 100 Guía rápida
Viessmann
Viessmann Vitotrol 300-B Instrucciones de funcionamiento
Viessmann
Viessmann VITOTROL 300 RF Instrucciones de funcionamiento
Viessmann
Viessmann Vitocom 100 Guía rápida
Viessmann
Viessmann VITOTROL 200 RF Manual de usuario
Viessmann
Viessmann VITOTROL 200-E Manual de usuario
Viessmann
Viessmann Vitotrol 350-C Guía rápida
Viessmann
Viessmann VITOTROL 200-E Guía rápida
Viessmann
Viessmann Vitotrol 300 Manual de usuario
Viessmann
Viessmann Vitocom 100 Instrucciones de funcionamiento
Viessmann
Viessmann VITOTROL 200-E Manual de usuario
