Victron energy BlueSolar PWM Series Manual de usuario

Manual

Handleiding

Manuel

Anleitung

Manual

Appendix

BlueSolar PWM Charge Controller – LCD - USB

12V | 24V | 5A

12V | 24V | 10A

12V | 24V | 20A

EN NL FR DE ES SV IT Appendix

1. General Information

The BlueSolar PWM Charge Controller series uses Pulse Width Modulation (PWM)

charge voltage control combined with a multistage charge control algorithm.

2. Features

•Three stage battery charging [bulk – absorption – float]

•Battery type: Lead-acid and LiFePO4 (with internal BMS)

•Protected against over current.

•Protected against short circuit.

•Protected against reverse polarity connection of the solar panels and/or battery.

•Low voltage load disconnect.

•Temperature protection.

3. Installation

Important note: always connect the batteries first.

IMPORTANT

•Always connect the battery first, in order to allow the Controller

to recognize system voltage

•Use a 12V (36 cells) solar array for a 12V system.

•Use a 24V (72 cells) solar array for a 24V system.

1. Connect the battery - plus and minus.

2. Connect the solar array - plus and minus.

3. Connect the load - plus and minus.

The reverse order applies when deinstalling.

An improper sequence order can damage the BlueSolar PWM Charge Controller!

1. Make sure the battery is charged for the BlueSolar PWM Charge Controller to recognize

the battery type before first installation.

2. The battery cable should be as short as possible to minimize losses.

3. The controller is suitable only for lead-acid, and LiFePO4 batteries.

4. The BlueSolar PWM Charge Controller is suitable only for regulating solar panels. Never

connect another charging source to the charge BlueSolar PWM Charge Controller.

EN NL FR DE ES SV IT Appendix

4. LCD DISPLAY and SETTINGS

4.1 Monitoring and settings

Values between [ ] are for 24V battery settings

Boot Display. After connecting the battery the display shows

the solar charger model and the system voltage as recognized

by the solar charger.

105=BlueSolar PWM Charge Controller – LCD - USB 12V|5A

205=BlueSolar PWM Charge Controller – LCD - USB 24V|5A

110=BlueSolar PWM Charge Controller – LCD - USB 12V|10A

210=BlueSolar PWM Charge Controller – LCD - USB 24V|10A

120=BlueSolar PWM Charge Controller – LCD - USB 12V|20A

220=BlueSolar PWM Charge Controller – LCD - USB 24V|20A

Press MENU to enter next display.

MENU：switch between different display, or to enter/exit setting by long

press.

UP：press to change the settings when in setting mode.

DOWN: press to change the settings when in setting mode.

Load on/off button when in H mode.

Main display: battery voltage, battery state of charge, charging

and discharging status.

Press MENU to enter next display.

Change settings in

Main display.

Press the MENU

button for several

seconds until the

display flashes, you

are in:

Battery type setting.

See table below.

The factory setting is b01

*The controllers do not have a remote on/off input. Therefore use LiFePO4 batteries with integrated BMS only

(such as the Victron SuperPack batteries)

Press on the MENU

key again and you

are in:

Low voltage disconnect

The factory setting is 11.2V [22.4V]

Press on the MENU

key again and you

are in:

Low voltage reconnect

The factory setting is 12.6V [25.2V]

Battery

type

Battery

voltage

Absorb

tion

voltage

Float

voltage

Low voltage

disconnect

factory

setting

Low voltage

disconnect

range

Low

voltage

reconnect

factory

setting

Low voltage

reconnect

range

b01

LEAD-

ACID

[AGM]

12.0V

[24V]

14.4V

[28.8V]

13.7V

[27.4V]

11.2V

[22.4V]

10.5V-12.0V

in steps of

0.1V

12.6V

[25.2V]

12.0V-13.5V in

steps of 0.1V

b02

LEAD-

ACID

[Gel]

12.0V

[24V]

14.2V

[28.4V]

13.7V

[27.4V]

11.2V

[22.4V]

10.5V-12.0V

in steps of

0.1V

12.6V

[25.2V]

12.0V-13.5V in

steps of 0.1V

b03

LEAD-

ACID

[Wet]

12.0V

[24V]

14.6V

[29.2V]

13.7V

[27.4V]

11.2V

[22.4V]

10.5V-12.0V

in steps of

0.1V

12.6V

[25.2V]

12.0V-13.5V in

steps of 0.1V

b04 12V

LiFePO4* 12.8V 14.2V 13.35V 11.2V

10.5V-12.0V

in steps of

0.1V

12.6V 12.0V-13.5V in

steps of 0.1V

b05 24V

LiFePO4* 25.6V 28.4V 26.7V 22.4V

21.0V-24.0V

in steps of

0.1V

25.2V 24.0V-27.0V in

steps of 0.1V

EN NL FR DE ES SV IT Appendix

PV Voltage display: PV voltage and the state of charge of

the battery.

Press MENU to enter next display.

Charge current display: PV to battery current and the state

of charge of the battery.

Press MENU to enter next display.

Load output settings.

The factory setting is 24h (load output always on)

Change load output

settings.

Press the MENU button

for several seconds until

the number flashes.

Load output setting.

See table below.

Press MENU to enter

the next display

(Note: the Phoenix

VE.Direct inverters can be

controlled by connecting to

the left side connection of

the remote control to the

load output)

Trigger level

When the BlueSolar PWM Charge Controller

is set to L01-L23 the solar panel voltage will

be measured to decide whether it is night or

day to switch the load on or off.

The factory setting is 4V.

Press MENU to enter

the next display

Trigger delay time

When the BlueSolar PWM Charge Controller

measures a solar panel voltage lower than

the trigger value it will delay for 10 seconds

and measure again to make sure night falls.

Factory setting: 10 seconds

The load can switched on and off by the Load on/off switch

Load D2D

Load will switch on at sunset and switch off at sunrise.

L01-L23

The load output will switch on after sunset and switch off after 1-23

hours.

24H

The BlueSolar PWM Charge Controller will continuously supply

power to the load.

Press MENU to enter

the next display

Short-circuit protection setting.

Some inductive or capacitive loads will trigger

the short-circuit protection during start up.

Therefore the SC-protection can be disabled

manually. Sc.F = OFF, Sc.n = ON. The

default is ON.

Discharge current display:

load current and battery capacity,

Press MENU

to enter next display.

USB Voltage display: USB voltage

5V (2A max)

Press MENU to enter next display.

Internal controller temperature. If the controller overheats it will shut

down and wait for the temperature to drop to normal level and then it will

start working again.

Press MENU to enter Main display.

EN NL FR DE ES SV IT Appendix

5. Alarms

High temperature

When temp ≥ 85℃, the controller will enter into the first

protection phase: it will lower the PV input current in order to

lower the temp. There is no alarm on the LCD display.

When temp >90℃, the controller will enter into the second

protection phase: the PV input current will be reduced to zero,

the load output will be switched off and a high temp alarm icon

will show on the LCD.

After the temp has decreased to less than 82℃, BlueSolar PWM

Charge Controller will resume normal operation.

Low battery voltage

When the battery is discharged to less than the Low Voltage

Disconnect (LVD) voltage, the controller will disable the load

output. After over-discharge the load output will be re-enabled

when the battery voltage reaches the Low Voltage Reconnect

(LVR) level.

Over-current protection.

A load output over-current or short-circuit is indicated by a

flashing load icon. The controller will disable the load output and

try to re-enable after 30 seconds.

Shut down after 60s in case of 110%-130% load.

Shut down after 5s in case of 130%-160% load.

Short-circuit protection

The BlueSolar PWM Charge Controller will switch off the load

output and wait for 30s and then try to restart. User should

check and remove the trouble in time.

6.Specifications

BlueSolar PWM Charge

Controller

12V|24V|5A

12V|24V|10A

12V|24V|20A

12V

24V

12V

24V

12V

24V

Battery Voltage

12/24V Auto Select

Charge & Load Current

10A

20A

Charge mode

PWM, Time and Lighting Control

Automatic load

disconnect

Yes

Maximum solar array

voltage

55V

Solar voltage range

15-28V [30-55V]2

Self-consumption

<10mA

Protections

Reverse polarity connection of the solar panels.

Reverse polarity connection of the battery.

Low voltage disconnect.

130% load: Shuts down after 60sec.

160% load: Shuts down after 5sec.

Short circuit: immediate shut down.

Over-temperature protection.

Solar Panel

Recommended solar panel

array

36cell [72cell]2

Max Solar Input Power

60W 120W 120W 240W 240W 480W

USB outputs

Voltage

Current

2A (total from 2 USB outputs)

Default settings

Absorption charge

(b01)

1 14.4V [28.8V]2

Float charge (b01)1

13.7V [27.4V]2

Load disconnect (b01)1

11.2V [22.4V]2

Load reconnect (b01)1

12.6V [25.2V]2

Enclosure

Terminal size

6mm² / AWG10

Weight

150gr

Dimension (h x w x d)

96 x 169 x 36 mm

Mounting

Vertical wall mount, indoor only

Humidity (non

condensing)

Max. 95%

Operating temperature

-35°C to +60°C (full load)

Cooling

Natural convection

Protection class

IP20

Standards

Safety

EN60335-1, IEC62109-1

EMC

EN61000-6-1, EN61000-6-3

1See also 3.1 Battery type setting.

2[V] values for 24V system.

Tabla de contenidos

Idiomas:

Otros manuales de Controladores de Victron energy

Victron energy

Victron energy BlueSolar MPPT 150/35 Manual de usuario

Victron energy

Victron energy SmartSolar MPPT RS 450 100 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/70-Tr Manual de usuario

Victron energy

Victron energy VE.Bus BMS Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/85 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 75/50 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/70 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/70 Manual de usuario

Victron energy

Victron energy SmartShunt IP65 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/60-Tr Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/85-Tr Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/45-MC4 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/35 Manual de usuario

Victron energy

Victron energy BlueSolar PWM DUO 12V 24V 20A LCD USB Manual de usuario

Victron energy

Victron energy SmartSolar MPPT 100/30 Manual de usuario

Victron energy

Victron energy EasySolar-II GX Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 100/30 Manual de usuario

Victron energy

Victron energy Cerbo GX Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/45-Tr Manual de usuario

Victron energy

Victron energy CCGX Manual de usuario

Victron energy

Victron energy BlueSolar 100/50A Manual de usuario

Victron energy

Victron energy CCGX Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 75/10 Manual de usuario

Victron energy

Victron energy Bluesolar-5 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario