Vicon SN663V-B Manual de usuario

1 Introduction

The Cruiser SN663V-B network camera is an outdoor camera dome that includes 1080p high

resolution camera lens combination that provides video transmission over a network. It is fully

featured for security surveillance and remote monitoring needs.

The camera provides triple-streaming video and supports H.264 compression technology,

drastically reducing file sizes and conserving valuable network bandwidth; M-JPEG compression is

also supported. By using its dedicated program, multiple users are able to have access to the

network camera simultaneously, or a single user can monitor various network cameras at the same

time. It also enable users to play, store and retrieve a monitoring image by using a PC. All the

settings and real time monitoring screens are provided through access to the web.

1.1 Components

The camera is designed with compact, small size, hard dome camera housing. The housing is

constructed of aluminum, steel and plastic. The housing is designed to be mounted on a wall or a

ceiling. The housing meets the Protection Classification IP66 standards for dust and moisture

resistance.

*DomeCamera 1

* Installation Guide/CD 1

* Template Sheet 1

* Mounting Bracket 1

* Safety Lanyard 1

* Accessory Kit 1

1) Mounting screws (PH6 x 35.0) (4)

2) Plastic anchors (4)

3) O-Rings (4)

4) Torx wrench (1)

* Accessory Connector 1

1) 3-Pin Terminal Block (1)

2) 6-Pin Terminal Block (1)

* RJ-45 Waterproof Cover 1

1.2 Key Features

• Brilliant video quality

The network camera offers the highly efficient H.264 video compression, which drastically

reduces bandwidth and storage requirements without compromising image quality. Motion

JPEG is also supported for increased flexibility.

• Dual or Triple Streams

The network camera can deliver dual or triple video streams simultaneously at full frame rate in

all resolutions up to Full-HD (1920 x 1080p) using Motion H.264 and JPEG. This means that

several video streams can be configured with different compression formats, resolutions and

frame rates for different needs.

• Image setting adjustment

The network camera also enables users to adjust image settings such as contrast, brightness

and saturation to improve images before encoding takes place.

• Intelligent video capabilities

The network camera includes intelligent capabilities such as VCA (Video Content Analysis).

The network camera’s external inputs and outputs can be connected to devices such as

sensors and relays, enabling the system to react to alarms and activate lights or open/close

doors.

• Improved Security

The network camera logs all user access, and lists currently connected users. Also, its full

frame rate video can be provided over HTTPS.

• PoE (Power over Ethernet)

This network camera can be powered through PoE, which simplifies installation since only one

cable is needed for carrying power, as well as video controls.

• ONVIF Certificate

This is a global interface standard that makes it easier for end users, integrators, consultants,

and manufacturers to take advantage of the possibilities offered by network video technology.

ONVIF enables interoperability between different vendor products, increased flexibility,

reduced cost, and future-proof systems.

• Micro-SD Recording support

The network camera also supports a Micro-SD memory slot for local recording with removable

storage.

• Audio support

The network camera also supports two-way audio.

2 Installation

2.1 Mounting the Camera

The dome camera is for use in surface or pendant mounting applications, and the mounting

surface must be capable of supporting loads of up to 10 lb (4.5 kg). (Pendant mounting must use

pendent mount accessory.)

The dome cameras mounting bracket should be attached to a structural object, such as hard wood,

wall stud or ceiling rafter that supports the weight of the dome camera.

CAUTION: A silicone rubber sealant must be applied to seal the housing to secure

waterproofing.

2.1.1 Locking the Camera

1. Make screw holes on the ceiling using the supplied mounting Template Sheet (Figure A).

2. Fix the Mounting Bracket to the ceiling using supplied Anchors (4x) and Mounting Screws (4x)

(Figure B).

3. Hook up the Safety Lanyard to the Safety Lanyard Hook of the Mounting Bracket (Figure C).

4. Align the locking tab on the bracket and the locking slot on the base of the dome (Figure D).

5. Turn the dome to the counterclockwise about 10 degree to the locked position (Figure E).

CAUTION: Before installing mounting bracket to surface pre-adjust the four mounting

screws “A” on the base of the dome camera to best match the mounting

bracket locked position. Unscrew the locking screw on the side of the dome’s

base and fit the tab of the mounting bracket into the locking slot. Screws “A”

should not be too tight or too loose when the dome is in the locked position.

After setting the proper positions of screws “A” remove the mounting bracket

and install it to the proper surface. If it is too difficult to lock the dome in

position after the mounting bracket has been installed readjust the screws

“A” by unscrewing them a small amount and try to install dome camera again.

2.2 Basic Configuration of Camera System

No. Connector Wire Color Description

1 3-pin terminal block RED 24VAC or 12VDC+

WHITE 24VAC or 12VDC-

2 6-pin terminal block

PINK ALARM INPUT 1

GRAY ALARM INPUT 2

GREEN ALARM INPUT 3

BLUE ALARM INPUT 4

BROWN GND

YELLOW ALARM OUTPUT

3 RJ-45 BLACK Ethernet, RJ-45 port compatible with

10/100Mbps having PoE functionality

4 STEREO jack GRAY AUDIO OUTPUT

5 STEREO jack BLACK AUDIO INPUT

The camera must be installed by qualified service personnel in accordance with all local and

federal electrical and building codes.

2.3 Micro-SD Card Insertion

User can install and change Micro-SD card as shown in the following picture.

1. Open the Micro-SD card cover.

2. Install or change Micro-SD card.

3. Tightly close the Micro-SD card cover to ensure waterproofness.

2.4 Connections

• Connecting the Network

Connect a standard RJ-45 cable to the network port of the camera. Generally a crossover

cable is used for directly connection to PC, while a direct cable is used for connection to a

hub.

• Connecting Audio

Connect speaker to audio output line and external mic to audio input line.

• Connecting Alarms

– A1, A2, A3, A4 (Alarm Input 1, 2, 3, 4)

You can use external devices to signal the camera to react on events. Mechanical or

electrical switches can be wired to the A1, A2, A3, A4 (Alarm Input 1, 2, 3, 4) and G

(Ground) connectors.

– G (Ground)

NOTE: All the connectors marked G or GND are common.

Connect the ground side of the alarm input and/or alarm output to the G (Ground)

connector.

– AO (Alarm Output)

The camera can activate external devices such as buzzers or lights. Connect the device to

the AO (Alarm Output) and G (Ground) connectors.

• Connecting the Power

Connect power of 12VDC or 24VAC for the camera.

When using a 12VDC adapter, connect the positive (+) pole to the ‘+’ position and the

negative (-) pole to the ‘-’ position.

Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source

only.

– Be careful not to reverse the polarity when you connect the power cable.

– You can also use a router featuring PoE (Power over Ethernet) to supply power to the

camera.

– 24VAC is recommended to use for the camera power for stable operation with heater kit.

If using PoE, the heater will not operate at all.

2.4.1 Network Connection & IP Assignment

The network camera is designed for use on an Ethernet network and requires an IP address for

access. Most networks today have a DHCP server that automatically assigns IP addresses to

connected devices. By the factory default, your camera is set to obtain the IP address

automatically via DHCP server. If your network does not have a DHCP server the network camera

will use 192.168.1.100 as the default IP address.

If DHCP is enabled and the product cannot be accessed, run the SmartManager utility on the CD

to search and allocate an IP address, or reset the product to the factory default settings and then

perform the installation again.

1) Connect the network camera/device to the network and power up.

2) Start SmartManager utility (Start > All programs > SmartManager > SmartManager).

The main window will display, and after a short while any network devices connected to the

network will be displayed in the list.

3) Select the camera on the list and click right button of the mouse. A pop-up menu displays as

below.

4) Select Assign IP Address. The Assign IP window will display. Enter the required IP address.

NOTE: For more information, refer to the SmartManager User’s Manual.

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vicon

Vicon

Vicon V672V-1 Instrucciones de funcionamiento

Vicon

Vicon roughneck V900 Manual de usuario

Vicon

Vicon V700-C Series Manual de usuario

Vicon

Vicon V9360-1 Manual de usuario

Vicon

Vicon ROUGHNECK V910 Manual de usuario

Vicon

Vicon Vantage V16 Manual de usuario

Vicon

Vicon Roughneck Pro V2000D Series Manual de usuario

Vicon

Vicon V15CCM-IR-2 Series Rouchneck Manual de usuario

Vicon

Vicon V905-CUBE Manual de usuario

Vicon

Vicon V923-N Manual de usuario

Vicon

Vicon VC-3000-DSP Manual de usuario

Vicon

Vicon I-Onyx MPD-955DN-O Manual de usuario

Vicon

Vicon SURVEYOR4A Manual de usuario

Vicon

Vicon V662-D Instrucciones de funcionamiento

Vicon

Vicon V9360-1 Manual de usuario

Vicon

Vicon VC-700W Manual de usuario

Vicon

Vicon V661V-Series Instrucciones de funcionamiento

Vicon

Vicon I-ONYX MPD-980DN-O Manual de usuario

Vicon

Vicon V960-N Series Manual de instrucciones

Vicon

Vicon Cruiser SN673V-C Manual de usuario

Vicon

Vicon VC275-24 Guía del usuario

Vicon

Vicon SURVEYOR 2000 S2000-CC22-EX Manual de usuario

Vicon

Vicon ROUGHNECK V-CELL-HD-A Manual de usuario

Vicon

Vicon V930D Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario