Viavi OneAdvisor 1000 Manual de usuario

VIAVI//Public

OneAdvisor 1000 High-Speed Network Testing Platform

QUICK CARD

Ethernet Layer 2 Traffic Loopback

This quick card describes how to set up the OneAdvisor 1000 100G Module as a Layer 2 Loopback

device.

LAUNCH TEST

1. Press the Power button to turn on the

OneAdvisor.

2. Press the 100G Module Test icon

at the top of the screen.

3. Tap the Power button and click

to launch the 100G Module.

4. Using the Select Test menu, Quick Launch

menu, or Job Manager, launch the Ethernet

Layer 2 Traffic test on Port 1 for the desired

data rate. For example:

Ethernet ►1GigE Optical ►Layer 2 Traffic

►P1 Terminate.

5. Tap to open the Tools Panel and

select .

6. Press to continue.

Figure 2: Launch 100G Module

Figure 3: Launch Test

Figure 1: Equipment Requirements

•OneAdvisor 1000 equippedwith the following:

o100G Transport Module

oBERT software release V30.1.0 or greater

oC510GELAN test option for 10 Gigabit Ethernet loopback

oC525GE test option for 25 Gigabit Ethernet loopback

oC540GE test option for 40 Gigabit Ethernet loopback

oC550GE test option for 50 Gigabit Ethernet loopback

oC5100GE test option for 100 Gigabit Ethernet loopback

•Optical Transceiver supporting the Ethernet data rate

to be tested (SFP or QSFP)

•Cables to match the optical transceiver and the line under test

•Fiber optic inspection microscope (P5000i or FiberChek Probe)

•Fiber optic cleaning supplies

VIAVI//Public

OneAdvisor 1000 High-Speed Network Testing Platform

QUICK CARD

►The followingInformation is needed to

configure the test:

•Physical Interface (10/100/1000BASE-T,

1000BASE-LX, 10GBASE-LR, 100GBASE-LR4,

etc.)

•Auto Negotiationsettings of the port

under test.

►For Optical Interfaces:

1. Press the Setup soft key on the

top right side of the screen.

2. Select the Interface/Connector folder.

3. Insert desired Optical Transceiver into

the Port 1 SFP or QSFP slot on the top

of the OneAdvisor.

4. Review SFP information in the

Connector tab:

oVerify that the SFP operates on the

required wavelength

(850nm, 1310nm or 1550nm).

oVerify that the SFP supports the

required Data Rate (1G, 10GE LAN,

etc).

oNote the Min and Max Tx Levels

(dBm) and Max Rx Level (dBm) to

assess if optical attenuators are

required.

oPress the Results soft key to

return to the Test Results screen.

►For 10/100/1000 Electrical and 1GigE

Optical tests, tap the Ethernet tab of the

Quick Configuration menu and set

Auto Neg. to the same value as the Ethernet

port under test (On or Off).

CONFIGURE TEST

Figure 5: Setup, Interface/Connector/SFP

Figure 6: Quick Config, Auto Neg.

Figure 4: Work Order

VIAVI//Public

OneAdvisor 1000 High-Speed Network Testing Platform

QUICK CARD

►For Optical Interfaces:

1. Use the VIAVI P5000i or FiberChekProbe

microscope to inspect both sides of every

connection being used (SFP, attenuators,

patch cables, bulkheads)

oFocus the fiber on the screen.

oIf it appears dirty, clean the fiber end-face

and re-inspect.

oIf it appears clean, run the inspectiontest.

oIf it fails, clean the fiber and re-run

inspection test. Repeat until it passes.

2. If necessary, insert optical attenuators into

the SFP TX and/or RX ports.

3. Connect the SFP to the port under test

using a jumper cable compatible with the

line under test.

4. Select the Laser tab in the Actions panel.

5. Press . The button will turn yellow

and be relabeled .

6. Press the Restart soft key .

7. Verify the following:

oSummary LED is yellow.

oSignal Present LED is green.

oSync Acquired LED is green.

oLink Active LED is green.

►For Copper 10/100/1000BASE-T interfaces:

1. Connect the 10/100/1000 RJ-45 jack to

the port under test using CAT 5E or better

cable.

2. Press the Restart soft key .

3. Verify the following:

oSummary LED is yellow.

oSync Acquired LED is green.

oLink Active LED is green.

Figure 8: Optical Interface Results

Figure 7: Inspect Before You Connect

CONNECT TO LINE UNDER TEST

Figure 9: Copper Interface Results

VIAVI//Public

OneAdvisor 1000 High-Speed Network Testing Platform

QUICK CARD

Product specifications and descriptions in this

document are subject to change without notice.

Patented as described at viavisolutions.com/patents

To reach the VIAVI office nearest you,

visit viavisolutions.com/contact

+1 844 GO VIAVI

(+1 844 468-4284)

LOOP UP

The OneAdvisor may be looped up by any of the

following methods. Once looped, the OneAdvisor

will reflect all received test packet after inverting

Source and Destination MAC addresses.

1. Broadcast Loop up message: The

OneAdvisor will respond to VIAVI Loop up

messages received via Broadcast MAC

address and enter Local Loopback (LLB) mode.

2. Unicast Loop up message:

►The OneAdvisor will respond to VIAVI

Loop up messages received via Unicast

MAC address and enter LLB mode.

3. Manual Local Loopback:

►Select the Actions Panel and tap

to manually enter LLB mode.

►Tap again to exit LLB mode

when the test is complete.

With Unicast and Manual loopback, the operator

of T-BERD or OneAdvisor traffic generator will

need to know the MAC address of this OneAdvisor:

►Tap the Setup soft key , select the

Ethernet menu, and tap

to display the Factory Default Source

MAC Address of your OneAdvisor.

►Provide this address to the operator of the

Traffic Generator, upon request.

►Press the Results soft key to view

the progress of the test.

Figure 12: Ethernet Setup, Source MAC

Figure 11: Manual LLB

Figure 10: Loop Up message response

Otros manuales de Equipo de prueba de Viavi

Viavi

Viavi IFR 6000 Manual de usuario

Viavi

Viavi SmartPocket OLP-39G Manual de usuario

Viavi

Viavi 3900 Series Manual de usuario

Viavi

Viavi T-BERD MTS 5800 Manual de lista de piezas

Viavi

Viavi OneAdvisor ONA-1000 400G Manual técnico

Viavi

Viavi OneAdvisor 800 400G Module Manual de usuario

Viavi

Viavi T-BERD/MTS 5800 Guía de instalación

Viavi

Viavi T-BERD/MTS-4000 v2 Manual de lista de piezas

Viavi

Viavi 8800SX Manual de usuario

Viavi

Viavi OneAdvisor 1000 Manual de usuario

Viavi

Viavi T-BERD/MTS-5800 Manual de lista de piezas

Viavi

Viavi T-BERD/MTS-2000 Manual de lista de piezas

Viavi

Viavi 3550 Manual de usuario

Viavi

Viavi HST-3000 Manual de lista de piezas

Viavi

Viavi T-BERD MTS 5800 Manual de lista de piezas

Viavi

Viavi P5000i Manual de usuario

Viavi

Viavi OTU-8000 Manual de lista de piezas

Viavi

Viavi T-BERD/MTS-2000 Manual de lista de piezas

Viavi

Viavi 4100 Series Manual de lista de piezas

Viavi

Viavi MSQ-900 Manual de usuario

Viavi

Viavi OBS-500 Manual de usuario

Viavi

Viavi RGS-2000NG Manual de usuario

Viavi

Viavi ALT-8000 Manual de lista de piezas

Viavi

Viavi AVX-10K Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario