VIA Technologies Zida BX983D Manual de usuario

Handling Precautions

CAUTION

High potential static charge may cause damage to the integrated circuits on the board. Before

handling any mainboard outside of its protective packaging, ensure that there is no static

electric charge in your body.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent

type recommended by the manufacturer.

There are some basic precautions when handling the motherboard or other computer components:

♦Keep the board in its anti-static bag until you are ready to install it.

♦Protect your board from static electricity by well grounding of your body and the equipment during the

installation, such as wearing a grounded wrist strap.

♦Always handle the board by its edges.

♦Do not touch the components on the boards, add-on cards/modules and the “gold finger” connectors

plugged into the expansion slot. It is better to handle system components by their mounting bracket.

♦Ensure the system power is completely turn-off before doing any installation work.

Notice to Customers

The information contains in this User’s Guide with no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of products including liability or warranties relating to fitness for a particular

purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. We shall not be

liable for any loss or profits, loss of business, loss of use or data, interruption of business, or for indirect, special,

incidental, or consequential damages arising from any defect or error in this User’s Guide or product.

We retains the right to make changes on this User’s Guide and product descriptions at any time, without notice.

Table of Contents

Page ii

Trademarks

VIA is a registered trademark of VIA Technologies, Incorporated.

Intel, Pentium, Pentium II, Celeron are registered trademark of Intel Corporation.

IBM, IBM PC, IBM PC/AT, PC-DOS, OS/2 and OS/2 WARP are registered trademarks of

International Business Machines Corporation.

MS-DOS, Windows, Windows NT, Windows 95 and Windows 98 are registered trademarks of

Microsoft Corporation.

AWARD BIOS is a product of Award Software Inc.

Third-party brands and names mentions in this User’s Guide are the property of their

respective owners.

User’s Guide Revision :1.01

Release Date : DECEMBER 1998

Part No : 90-BX3D1.01-00

Table of Contents

Page iii

Table of Contents

OVERVIEW....................................................................................................................................................4

AUTO JUMPER...............................................................................................................................................4

FEATURES SUMMARY....................................................................................................................................5

MAINBOARD INSTALLATION.........................................................................................................................6

CPU INSTALLATION......................................................................................................................................7

INSTALLING SYSTEM MEMORY (RAM)..........................................................................................................9

EXPANSION CARDS INSTALLATION ..............................................................................................................10

CONNECTING EXTERNAL CONNECTOR .........................................................................................................10

“AUTO JUMPER” GUIDE ..............................................................................................................................15

QUICK INSTALLATION GUIDE........................................................................................................................ 17

AWARD BIOS AND CMOS SETUP UTILITY .......................................................................................................20

AWARD CMOS SETUP.................................................................................................................................. 21

STANDARD CMOS SETUP...............................................................................................................................23

BIOS FEATURES SETUP .................................................................................................................................25

CHIPSET FEATURES SETUP.......................................................................................................................... 28

POWER MANAGEMENT SETUP.......................................................................................................................30

PNP/PCI CONFIGURATION ....................................................................................................................34

CPU SPEED SETTING..............................................................................................................................37

INTEGRATRD PERIPHERALS................................................................................................................38

QUICK REFERENCE OF MOTHERBOARD..........................................................................................................41

Mainboard Installation

Page 4

Features of the Board

OVERVIEW

Congratulations on purchasing the highest performance motherboard. With the advanced technologies

available today, this motherboard is designed to optimize for Intel’s processors. Three unbuffered, 3.3

Volts, 168-pin DIMM sockets are included for supporting SDRAM.

This motherboard utilizes VIA's VT82C691 PCI chipset. The VIA’s VT82C586B PCI/ISA IDE provides

an integrated Bus Mastering IDE controller with two high performance IDE interfaces for up to four IDE

devices (such as hard drives or CD-ROM). The integrated super I/O controller integrates the standard PC

I/O functions: floppy interface, two FIFO serial ports, one EPP/ECP capable parallel port, and support for

an IrDA and Consumer Infra Red compatible interface.

This mainboard is designed to support the new graphic interface standard, Accelerated Graphic Port (AGP),

The AGP interface can reach a theoretical ~532Mbytes/sec transfer rate for 3D graphics data. On the other

hand, the on-board 32-bit PCI local bus slots allow a high bandwidth data path, which serves as a super

highway, for intensive data-movement such as networking. The BIOS support PCI bridge user

configuration, which allows for further expansion of the system with PCI peripherals. Up to two 16-bit ISA

slots allow this board to be backward compatible with the older expansion card. A total of six expansion

slots may be populated with full length add-in cards, since one PCI and ISA slot share the same chassis I/O

panel.

AUTO JUMPER

This mainboard is within our “Auto Jumper” series, which eliminates the necessity for the user to be

bored by jumper settings on the motherboard. It is capable of detecting the CPU brand and core voltage,

setting the appropriate CPU speed according to instructions from the user through CMOS setup menu.

In addition, two “safe keys” are defined. Pressing“F”during power on clears the CMOS RAM data, while

pressing “J”during power on re-detects CPU in “Auto Jumper” mode.

Mainboard Installation

Page 5

FEATURES SUMMARY

This motherboard comes with following features:

þSupports Intel PENTIUM II® orCeleron® Processor with automatic voltage adjustment for BX98-3D.

þSupports Intel Socket 370 Celeron® Processor with automatic voltage adjustment for BX3D-CT.

þOptimized for the highest performance Intel PENTIUM II® processors with 100 MHz front-side bus for

BX98-3D

þOptimized for the highest performance Intel Socket 370 Celeron® processors with overclock 100 MHz front-

side bus for BX3D-CT

þAWARD PnP BIOS with support for power management, enhanced IDE/SCSI features and desktop

management interface (DMI) which allows higher level of hardware compatibility.

þFlash BIOS for a more easy upgrade path.

þThree 168-pin DIMM sockets support up to 768MB SDRAM

þOne Accelerated graphic port (AGP) for AGP card.

þTwo 16-bit ISA expansion slots and four 32-bit PCI expansion slots.

þIntegrated two PCI bus mastering Ultra IDE controller with two on-board connectors supporting up to

four IDE devices such as Hard Disk, CD-ROM or Tape Backup drives.

þIntegrated super I/O chip featuring one floppy disk controller, two 16550 UART compatible serial

ports, one high speed EPP/ECP parallel port, one Infra Red port.

þSupports “Auto Jumper ” for detecting CPU configurations.

þWAKEUP-LINK interface header supporting Intel Wake-On-LAN

þSupport either an AT or an ATX power supply

þSupport “ Modem Ring Wakeup “

Mainboard Installation

Page 6

MAINBOARD INSTALLATION

Installation Precautions

During installation and initial test, use caution to avoid personal injury and damage to wiring due to sharp

pins on connectors and printed circuit assemblies, rough chassis edges and corners, and hot components.

Adhere to warnings and limitations regarding accessibility into areas designated only for authorized

technical personnel.

A Quick Introduction

To Install and operate your the new motherboard, you must follow the steps below:

1. Install the CPU with cooling fan

2. Install RAM modules

3. Connect cables, wires and power connector

4. Install expansion cards

Auto Jumper

After hardware installation, the user should select the appropriate CPU speed in the “CPU

CONFIGURATION SETUP” menu within the CMOS setup. Notice that there exists no jumper on this

mainboard. The user may clear the CMOS content by pressing “F”key while switching on the system.

If a wrong CPU speed is selected, the system may behave unstable, causing the user not being able to get

into CMOS setup. Pressing the “J” key while switching on the system can make re-selection in this case.

Mainboard Installation

Page 7

CPU CARD INSTALLATION

The mainboard provides a 242-pin CPU card slot. The CPU card should have a fan attached to it to prevent

overheating. If this is not the case then purchase a fan before you turn-on the system. There is one CPU fan

power connector named J6 on-board.

+12V

(Red) Ground

(Black)

CPU FAN

Fig. 2 CPU Cooling Fan Installation Diagram

CAUTION

Without an effective cooling fan, the CPU can overheat and cause damage to both the CPU

and the motherboard.

CPU Cooling fan Connector

J6 provide the +12 Volts d.c. for your CPU cooling fan

J6 Signal Name

1NC

2 +12V

3Ground

Mainboard Installation

Page 8

CPU INSTALLATION

The motherboard provides a 370 pins, Socket 370. The CPU should have a fan attached to it to prevent

overheating. If this is not the case then purchase a fan before you turn-on the system.

Socket 370

Intel

CPU

45 degree Index

corner

CPU

COOLING

FAN

+12V (Red)

Ground (Black)

CPU Installation Diagram

CAUTION

Without a effective cooling fan, the CPU can overheat and cause damage to both the CPU

and the motherboard.

Mainboard Installation

Page 9

INSTALLING SYSTEM MEMORY (RAM)

The motherboard supports three 168-pin DIMM. The three 168-pin DIMM sockets are divided into three

banks and each bank can accept SDRAM module.

3.3V Key

Unbuffered

DRAM Key

Push to remove

DIMM module

Push to remove

DIMM module

64 Bit 168 PIN DIMM Module

Vertically insert

for installation

Fig. 3 168-Pin DIMM Module Installation Diagram

Mainboard Installation

Page 10

Expansion Cards Installation

At the most of beginning, you must read your expansion card documentation on any hardware and software

settings that may be required. The installation procedures are summarized as below:

1. Read the User’s Guide/Manual of your expansion card.

2. If necessary, set any jumpers on your expansion card.

3. Power-off the system and then disconnected the power cord.

4. Remove your computer’s cover.

5. Remove the metal bracket from one of the empty slot, ISA or PCI, corresponding to the type

of expansion card.

6. Carefully align the card’s connectors and press firmly, make sure at the connection is good.

7. Secure the card on the slot.

8. Replace the computer’s cover.

9. Setup the BIOS configuration if necessary.

10. Install the required software drivers for your expansion card.

CAUTION

Before adding or removing any expansion card or other system components, make sure that

you unplug your system power supply. Failure to do so may cause damage of your

motherboard and expansion cards.

Connecting External Connector

AT Power Connector

A 12-Pin power supplies provide two plugs incorporates standard ±5V and ±12V, each containing six wires,

two of which are black. Orient the connectors so that the black wires are together.

Pin Signal Name Pin Signal Name

1Power Good Signal 7Ground

2+5V 8Ground

3+12V 9-5V

4-12V 10 +5V

5Ground 11 +5V

6Ground 12 +5V

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de VIA Technologies

VIA Technologies

VIA Technologies VT310-DP Manual de usuario

VIA Technologies

VIA Technologies ARTIGO A2000 - VIA ARTiGO Barebone Storage... Manual de usuario

VIA Technologies

VIA Technologies VIA P4PB 266E Manual de usuario

VIA Technologies

VIA Technologies EPIA-M910 Manual de usuario

VIA Technologies

VIA Technologies ARTIGO A2000 - VIA ARTiGO Barebone Storage... Manual de usuario

VIA Technologies

VIA Technologies KM400 Manual de usuario

VIA Technologies

VIA Technologies NAB-7500 Manual de usuario

VIA Technologies

VIA Technologies EPIA-P830 Manual de usuario

VIA Technologies

VIA Technologies COMe-8X90 Manual de usuario

VIA Technologies

VIA Technologies VX800 Series Manual de usuario

VIA Technologies

VIA Technologies EPIA-M850 Manual de usuario

VIA Technologies

VIA Technologies VT82C691 Manual de uso y cuidado

VIA Technologies

VIA Technologies K8T890 Manual de usuario

VIA Technologies

VIA Technologies EPIA LT-Series Manual de usuario

VIA Technologies

VIA Technologies VAB-800 Manual de usuario

VIA Technologies

VIA Technologies EPIA-P700 Manual de usuario

VIA Technologies

VIA Technologies EITX-3001 Manual de usuario

VIA Technologies

VIA Technologies VAB-1000 Manual de usuario

VIA Technologies

VIA Technologies EPIA-PX5000EG - VIA Motherboard - Pico ITX Manual de usuario

VIA Technologies

VIA Technologies VB8002 Manual de usuario

VIA Technologies

VIA Technologies EPIA ME6000 - VIA Motherboard - Mini ITX Manual de usuario

VIA Technologies

VIA Technologies VIA P4XB-SA Manual de usuario

VIA Technologies

VIA Technologies EPIA-P830 Manual de usuario

VIA Technologies

VIA Technologies P4PB ULTRA-URL Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario