Vertiv AutoView AV104 Instrucciones de instalación y mantenimiento

Vertiv™ AutoView™

AV104/AV108/AV116 Switch

Installer/User Guide

EMIStatements

Products which are certified for EMC in the regions or countries indicated will have the required marking

or statement on the product label. The applicable statement for that country is listed below.

Taiwan

警告使用者

這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會

被要求採取某些適當的對策。

Technical Support Site

If you encounter any installation or operational issues with your product, check the pertinent section of

this manual to see if the issue can be resolved by following outlined procedures. For additional assistance,

visit https://www.VertivCo.com/en-us/support/.

TABLE OF CONTENTS

1 Product Overview 1

1.1 Features and Benefits 1

2 Basic Operation 3

2.1 Using Keystroke Commands 4

2.1.1 Activation sequence commands 4

2.2 Using the On-Screen Display 5

2.3 Switching Between Targets 7

2.3.1 Local port commands 7

2.4 Enabling Port Binding 7

2.4.1 Pass-through USB port commands 8

2.5 Operating Scan Mode 8

2.5.1 Scan mode commands 8

2.6 Cascading Units 9

2.7 Upgrading Firmware 10

3 Appendix 11

Appendix A: Product Specification 11

Vertiv | Vertiv™ AutoView™ AV104/AV108/AV116 Switch Installer/User Guide | i

Vertiv | Vertiv™ AutoView™ AV104/AV108/AV116 Switch Installer/User Guide | ii

1 PRODUCT OVERVIEW

The Vertiv™ AutoView™ AV104/AV108/AV116 is a single-user analog switch that supports up to four, eight

or 16 target devices and can be 0U or 1U rack-mounted or used as a desktop device. It supports USB

keyboard, mouse and VGA video at the local user interface and USB and VGA or DisplayPort video at the

target devices. The switch does not have a web interface, therefore, all switching is done locally.

1.1 Features and Benefits

Depending on the model, the switch provides the following features and benefits:

•Buttons for switching among KVMtarget devices

•LEDlights that indicate active and connected targets

•Hotkey switching functionality

•On-screen display switching

•Three USB2.0 Type-A ports for connecting a keyboard, mouse and flash drive for firmware

upgrades

•Two USB 2.0 Type-A pass-through ports to allow you to use connected devices on a selected

target

•VGAvideo output to the local monitor of up to at least 2048 x 1536 pixels

NOTE: The 4-port model does not have on-screen display capability.

NOTE: The unit does not support an absolute mouse. Support is provided for a five-button, scrolling,

relative mouse.

Vertiv | Vertiv™ AutoView™ AV104/AV108/AV116 Switch Installer/User Guide | 1

Vertiv | Vertiv™ AutoView™ AV104/AV108/AV116 Switch Installer/User Guide | 2

This page intentionally left blank.

2 BASIC OPERATION

The target devices connect to the product through a high density 26-pin connector and custom cable

with USB and VGA connections to the target. A second custom cable has a built-in DisplayPort to

VGAadaptor that provides a DisplayPort connection to the target. The custom cables are available in

lengths of six or 12 feet. A third custom cable supports cascading between switches. It is identical to the

VGA cables but is one foot in length. Contact your Vertiv™ representative to purchase the custom cables.

Depending on the model, you can switch between target devices using the front panel buttons, the on-

screen display or hotkeys. On-screen display switching is enabled on the AV108 and AV116 switch. When

a connected target device is powered, the corresponding LEDon the bottom of the button illuminates

orange. When the powered target device is selected, the corresponding LEDon the top of the button

illuminates green. The switch does not have a sleep or hibernation mode. It remains powered as long as

power is provided.

Figure 2.1 AV116 Front and Back Panel

ITEM DESCRIPTION

1 USB 2.0 Type-Apass-through ports

2 Capacitive port selection touch buttons

3 AC C14 power input connector

4 HD15 VGAconnector

5 USB 2.0 Type-A connector for a keyboard

6 USB 2.0 Type-A connector for a firmware upgrade peripheral

7 USB 2.0 Type-A connector for a mouse

8 HD26 target port connectors

Table 2.1 Front and Back Panel Components

Vertiv | Vertiv™ AutoView™ AV104/AV108/AV116 Switch Installer/User Guide | 3

Figure 2.2 Front Panel Capacitative Buttons and LEDs

ITEM DESCRIPTION

1 Indicates target is not powered or not connected

2 Indicates target is connected and powered

3 Indicates target is connected, powered and selected

Table 2.2 Switch Buttons and LED Indicators

2.1 Using Keystroke Commands

The AV104/AV108/AV116 switch supports hotkey functionality. You can use hotkey functionality to do

the following:

•Switch KVM between ports

•Switch USB pass-through between ports

•Start and stop scan mode

The default command mode is Ctrl+Ctrl+ [COMMAND]. When activating command mode, Ctrl +Ctrl must

be pressed sequentially within one second of each other. You can change the default command mode

using activation sequence commands. The commands are not case sensitive.

When in command (hotkey) mode, only keystrokes are passed to the target computer. Mouse activity is

disabled.

To exit command mode:

Press Enter to accept the action.

NOTE: You must press Enter to complete the command mode action. There is no way to abort a hotkey

sequence unless you enter an incorrect key sequence.

2.1.1 Activation sequence commands

The activation sequence commands allow you to activate default command mode or change the

activation sequence.

KEY SEQUENCE ACTION

Ctrl+Ctrl+H+1+Enter Activates the default command mode (Ctrl+Ctrl).

Ctrl+Ctrl+H+2+Enter Changes the activation sequence to Alt + Alt.

Ctrl+Ctrl+H+3+Enter Changes the activation sequence to Shift + Shift.

Table 2.3 Activation Sequence Commands

Vertiv | Vertiv™ AutoView™ AV104/AV108/AV116 Switch Installer/User Guide | 4

2.2 Using the On-Screen Display

In addition to using the front panel buttons and keystroke commands, you can use the on-screen display

to control port selection and to rename target devices, enable or disable port binding, display the firmware

version and adjust the scan time interval.

You can also rename supported targets from the on-screen display. Target names are limited to 24

English characters.

Since the on-screen display does not support mouse functionality, the arrow keys can be used to navigate

among the target devices.

To initiate the on-screen display with a list of targets:

Press Print Screen or press Ctrl+Ctrl+O+Enter.

Figure 2.3 On-Screen Display Initial Window

ITEM DESCRIPTION

1 USB pass-through icon (unbound shown)

2 Target powered icon (powered shown)

3 Target field (selected target field shown)

Table 2.4 On-Screen Display Initial Window

A green circle appears next to powered targets, a locked icon appears next to a target bound to a port via

USB pass-through and an unlocked icon appears next to an unbound target.

To bind or unbind a target:

1. Use the arrow keys to navigate to the target and press Enter.

Vertiv | Vertiv™ AutoView™ AV104/AV108/AV116 Switch Installer/User Guide | 5

2. Press Bto bind the target.

-or-

Press Uto unbind the target.

To assign or edit a target name:

1. Use the arrow keys to navigate to the target field and press E.

2. Type the name in the target field.

3. Press Enter to save.

-or-

Press Esc to exit without saving.

To set a scan time and run a scan:

Figure 2.4 Enter Scan Time Dialog Box with Default Time

1. Press Tand press Backspace to clear the existing scan time value.

NOTE: The scan time value indicates seconds. The default scan time is 30 seconds.

2. Enter a value between 02 and 60.

3. Press Enterto save the scan time.

4. Press Sto start the scan.

To view the firmware version:

Press V.

Vertiv | Vertiv™ AutoView™ AV104/AV108/AV116 Switch Installer/User Guide | 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Vertiv

Vertiv

Vertiv Cybex SC KM 120 Manual de usuario

Vertiv

Vertiv CYBEX SC Series Manual de usuario

Vertiv

Vertiv CYBEX SC Series Manual de usuario

Vertiv

Vertiv Cybex SC KM 120 Instrucciones de instalación y mantenimiento

Vertiv

Vertiv CYBEX SC Series Manual de usuario

Vertiv

Vertiv UL891 Instrucciones de instalación y mantenimiento

Vertiv

Vertiv AVOCENT SV Series Manual de usuario

Vertiv

Vertiv AVOCENT SV 340H Manual de usuario

Vertiv

Vertiv Cybex SC KM 120 Instrucciones de instalación y mantenimiento

Vertiv

Vertiv Remote Access Key Manual de usuario

Vertiv

Vertiv Avocent MergePoint Unity Instrucciones de instalación y mantenimiento

Vertiv

Vertiv Cybex SC 840 Manual de usuario

Vertiv

Vertiv XTE PTS Series Instrucciones de funcionamiento e instalación

Vertiv

Vertiv Avocent SV Instrucciones de instalación y mantenimiento

Vertiv

Vertiv CYBEX SC Series Manual de usuario

Vertiv

Vertiv AVOCENT SV Series Manual de usuario

Vertiv

Vertiv Cybex SC 820DP Manual de usuario

Vertiv

Vertiv Cybex SC 840D Manual de usuario

Vertiv

Vertiv GEIST SA1-01003LNB Manual de usuario

Vertiv

Vertiv SC1045XD Manual de usuario

Vertiv

Vertiv Cybex SC 920DP Manual de usuario

Vertiv

Vertiv SCKM180 Manual de usuario

Vertiv

Vertiv Liebert NXL SCCi Manual de usuario

Vertiv

Vertiv Liebert STS2 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario