VERIPURE VERIPUREVPC5000 Manual de usuario
1
REVISED 4/13/2020
OWNERS MANUAL VERIPUREVPC5000
2
2425 HUTSON ROAD
GREEN BAY WI, 54303
(920) 613-6771
www.veripure.com
THANK YOU FOR CHOOSING VERIPURE®
PLEASE TAKE A FEW MOMENTS TO FILL IN THE INFORMATION BELOW, SAVE THIS
MANUAL AS A CONVENIENT INFORMATION SOURCE FOR YOUR VERIPURE® SYSTEM.
Date of Purchase:
Purchased From:
Phone Number:
Serial Number:
Installed By:
Dealer Name:
Dealer Phone
3
PERFORMANCE DATA SHEET
Model VPC5000 & Model VP5000
This system has been tested by WQA according to NSF/ANSI 42 and 53 for the reducon of the substances
listed below. The concentraon of the indicated substances in water entering the system was reduced to a
concentraon less than of equal to the permissible limit for water leaving the system, as specied in NSF/
ANSI 42 and 53. While tesng was performed under standard laboratory condions, actual performance
may vary. Do not use with water that is microbiologically unsafe or of unknown quality without adequate
disinfecon before or aer the system. Systems cered for cyst reducon may be used on disinfected
waters that may contain lterable cysts.
Stage One — Filtraon Process:
The VeriPure Maintenance Kit- Consists of a two lter conguraon that is a proprietary design of VeriPure, Inc. The rst lter
is a sediment lter that greatly reduces suspended and parculate maer from the incoming water source. The second lter
(a carbon block lter for cyst removal, lead and chlorine reducon) greatly reduces free chlorine and cysts from the water
source to disinfect and improve the taste and odor of the water.
Carbon Block Filter Data
Operang Specicaons:
Capacity: 1 ,250 Gallons Lead Reducon
Flow Rate: 0.50 to 1.0 GPM
Minimum Pressure: 50 PSI
Maximum Pressure: 125 PSI
Temperature: 35-90 F (2-32 C)
Parameter
Chlorine >=50%
Cyst >=99.95%
Lead 0.01 mg/L
4
IMPORTANT SAFEGUARDS AND PRECAUTIONS
• INSTALL YOUR VERIPURE® SYSTEM IN COMPLIANCE WITH STATE AND LOCAL LAWS AND
REGULATIONS FOR PLUMBING AND ELECTRICAL CODES. AS WITH ANY WATER DEVICE, PLEASE
CHECK YOUR SYSTEM FOR LEAKS ON A REGULAR BASIS. CONTACT A PLUMBER IMMEDIATELY
• VERIPURE® PERFORMANCE IS BASED UPON INPUT WATER WHICH MEETS MINIMUM EPA
NATIONAL PRIMARY AND SECONDARY DRINKING WATER STANDARDS.
• SEE WWW.EPA.GOV/DWSTANDARDSREGULATIONS
•
ATTENTION: THIS UNIT IS DESIGNED FOR TREATMENT OF COLD WATER ONLY.
• READ INSTRUCTIONS- ALL SAFETY AND OPERATING INSTRUCTIONS SHOULD BE READ BEFORE THE UNIT IS
OPERATED.
• RETAIN INSTRUCTIONS– SAFETY AND OPERATING INSTRUCTIONS SHOULD BE KEPT IN AN ACCESSIBLE LOCATION
FOR FUTURE REFERENCE.
• FOLLOW INSTRUCTIONS– ALL INSTRUCTIONS SHOULD BE FOLLOWED FOR MAINTAINING AND OPERATING YOUR
VERIPURE® SYSTEM PROPERLY.
• MAINTENANCE PRECUATIONS– ALWAYS TURN OFF THE WATER SUPPLY AT THE SINK OR WATER SOURCE AND
UNPLUG POWER JACK FROM THE VERIPURE® SYSTEM BEFORE PERFORMING ANY MAINTENANCE.
• ACCESSORIES– DO NOT USE ANY ACCESSORIES, INCLUDING FILTER CARTRIDGES THAT ARE NOT RECOMMENDED
BY VERIPURE®
• WATER AND MOISTURE– DO NOT ALLOW MOISTURE TO CONTACT ANY INTERNAL OR EXTERNAL ELECTRONIC
COMPONENTS. SHOULD A LEAK OCCUR, IMMEDIATELY SHUT OFF THE WATER SUPPLY AND CONTACT YOUR
DEALER OR DISTRIBUTOR FOR SERVICE.
• POWER SOURCES– YOUR VERIPURE® SYSTEM SHOULD ONLY BE OPERATED FROM THE TYPE OF POWER SOURCE
INDICATED ON YOUR AC ADAPTER. IF YOU ARE NOT CERTAIN OF THE TYPE OF POWER SUPPLY TO THE OUTLET
PLEASE CONSULT YOUR VERIPURE® DEALER OR POWER COMPANY. ALTERNATIVE POWER SUPPLY ADAPTERS FOR
VOLTAGES FOUND IN MANY COUNTRIES OUTSIDE THE UNITED STATES ARE AVAILABLE THROUGH YOUR DEALER
ON SPECIAL ORDER. YOUR VERIPURE® SYSTEM MAY ALSO BE OPERATED WITH A BATTERY PACK OR GENERTOR.
• POWER CORD PROTECTION– VERIPURE® RECCOMENDS THAT POWER SUPPLY CORDS SHOULD BE ROUTED SO
THAT THEY ARE NOT LIKELY TO BE WALKED ON OR PINCHED BY ITEMS PLACED UPON OR AGAINST THEM.
5
HOW YOUR VERIPURE® SYSTEM WORKS
YOUR PATENTED VERIPURE® SYSTEM HAS BEEN DESIGNED TO USE TWO STAGES OF PRIMARY FILTRATION
AND LOW LEVEL OZONE TECHNOLOGY®. OPERATIONAL MAINTENANCE AND REPLACEMENT REQUIREMENTS
ARE ESSENTIAL FOR THE VERIPURE® SYSTEM TO PERFORM TO SPECIFIATIONS. CONTACT YOUR LOCAL
DEALER OR DISTRIBUTOR FOR REPLACEMENT FILTERS AND PARTS, OR CONTACT VERIPURE FOR THE DEALER
NEAREST YOU. THE VERIPURE® SYSTEM IS RECCOMENDED TO BE CONNECTED TO MUNICIPAL WATER
SOURCES.
FOOD & SURFACES
GENERAL RECOMENDATIONS FOR USING OZONATED WATER ARE AS FOLLOWS-
• PLACE ITEM OR ITEMS TO BE WASHED UNDER A STEADY STREAM OF VERIPURE® WATER AND RINSE.
• FOOD PREPARATION: IT IS RECOMMENDED ITEMS BE RINSED FOR 3 MINUTES WITH VERIPURE® WATER.
• FOOD ITEMS: PLACE IN A BOWL, COLANDER OR STRAINER. RINSE WITH VERIPURE® WATER.
STORING WATER
• SELECT A CONTAINER THAT IS FOOD GRADE QUALITY, SUCH AS GLASS OR STAINLESS STEEL. THOROUGHLY RINSE
THE CONTAINER WITH VERIPURE® WATER AT LEAST TWICE. FILL THE CONTAINER TO WITHIN ONE TO TWO INCHES
FROM THE TOP AND REPLACE CAP.
• STORE WATER IN REFRIGERATOR AND MAKE CERTAIN THE CAP IS REPLACED AFTER EVERY USE.
• WHEN WATER IS FRESHLY OZONATED YOU MAY INITIALLY BE ABLE TO DETECT A SLIGHT HINT OF OZONE. PEOPLE
VARY IN THEIR SENSITIVITY TO OZONE. ANY HINT OF THE OZONE TASTE WILL DISAPPEAR WITHIN A SHORT PERIOD
OF TIME. YOUR SYSTEM PRODUCES MINIMAL WASTE WHILE PRESERVING MINERALS IN YOUR WATER.
IMPORTANT NOTE: VERIPURE® PERFORMANCE IS BASED UPON INPUT WATER WHICH MEETS MINIMUM
EPA NATIONAL PRIMARY AND SECONDARY DRINKING WATER STANDARDS. SEE WWW.EPA.GOV/
DWSTANDARDSREGULATIONS
6
A LOOK AT YOUR VERIPURE® SYSTEM
UNIT DIMENSIONS: 11.5”L X 7”W X 5.5”H 9.0LBS (4.05KG)
IT IS IMPORTANT TO BE FAMILIAR WITH CERTAIN COMPONENTS OF YOUR VERIPURE® SYSTEM FOR
MAINTENANCE PURPOSES.
DIAGRAM 1
7
INSTALLATION INSTRUCTIONS
BEFORE INSTALLING
1. YOUR VERIPURE® SYSTEM IS DESIGNED TO BE USED WITH COLD WATER ONLY.
2. NEVER RUN WARM OR HOT WATER THROUGH YOUR VERIPURE® SYSTEM AS HOT WATER
CAN DAMAGE THE CARBON BLOCK FILTER.
3. WATER TEMPERATURES ABOVE 90° F CANNOT CONTAIN DISSOLVED OZONE; THUS
ELIMINATING DISINFECTION. WATER TEMPS APPROACHING 85° F REQUIRE LONGER
PERIODS OF CONTACT TIME FOR DISINFECTION PURPOSES.
4. FOR OPTIMAL PERFORMANCE , LIMIT YOUR VERIPURE® SYSTEM TO 70 PSI OF WATER
PRESSURE. VERIPURE® RECOMMENDS A MINIMUM WATER PRESSURE OF 50 PSI. LOW
WATER PRESSURE WILL CAUSE YOUR VERIPURE® SYSTEM TO PRODUCE A LOWER
QUANTITY OF FILTERED AND OZONATED WATER.
5. POWER REQUIREMENTS ARE 120 VAC 60 HZ. USE AC ADAPTER PROVIDED WITH YOUR
SYSTEM.
NOTE: VERIPURE® UNITS ARE DESIGNED TO BE UNDER CONTINUAL WATER PRESSURE WHEN
INSTALLED AND NOT IN USE, THE ON/OFF VALVE AND OR FAUCET SHOULD BE ON THE
OUTLET OF THE VERIPURE AT OR BETWEEN THE POU AND VERIPURE® UNIT. THIS ENSURES
PROPER FUNCTION ON THE VERIPURE® .
VPC5000 INSTALLATION INSTRUCTIONS BEGIN ON NEXT PAGE (PAGE 8)
8
INSTALLATION INSTRUCTIONS(VPC5000)
*COMMERCIAL/COUNTER-TOP MODEL*
Due to variance in plumbing and power outlets; we recommend that a plumber and or electrician install your VeriPure® System
by following these installaon instrucons. If you choose to install the unit yourself please call (920) 613-6771 for assistance.
Installaon of the VeriPure® System must conform to state and local plumbing and electrical codes, laws, regulaons and the
instrucons provided with your VeriPure® System. Failure to install as instructed will void the warranty.
Please check your VeriPure® System to be certain all items listed below are included.
• QTY 1 AC ADAPTER (POWER
SUPPLY) WITH OUTLET PLUG
• QTY 1 DIVERTER VALVE ASSEMBLY
• QTY 1 FAUCET ADAPTERS (QTY 3)
• QTY 1 MOUNTING PLATE
• QTY 1 HEX WRENCH
• QTY 1 SPANNER TOOL
• QTY 1 COLD WATER ONLY LABEL
• QTY 4 RUBBER FEET
• QTY 1 OWNERS MANUAL
9
VPC5000 WALL MOUNT INSTALLATION STEPS
Step 1: Please inspect your VeriPure® System Glass Dielectric Tube at this me. Locate the knob on your
VeriPure® System. Rotate 1/4 turn counter clockwise and PULL STRAIGHT OUT VERY CAREFULLY as to prevent
breaking. Inspect the dielectric for any cracks or breakage that may have occurred in shipping. If none are found, then
replace dielectric. When replacing dielectric, rotate 1/4 turn clockwise to lock in place.
Step 2: Locate the power outlet for the power supply.
Step 3: Locate the best area for hanging the VeriPure® System. Directly above the faucet or slightly to the le. Aach
the diverter valve to the faucet, CAUTION: DO NOT OVERTIGHTEN. Stretch out the hoses to get an approximate
locaon for the VeriPure® System.
Step 4: Mount screws for the VeriPure® System by using the provided screws and mounng plate.
Step 5: Locate the 1/4" lter inlet ng on your VeriPure® System. Remove the 3/8" red locking clip also located on
your VeriPure® System on the 3/8" outlet ng.
Step 6: Mount your VeriPure® System onto the mounng screws previously installed and ghten screws.
Step 7: Insert the 1/4” stem adapter ng at the end of the hose into the 1/4" lter inlet ng on your
VeriPure® System.
Step 8: Insert the other end of the 3/8" tubing into the 3/8" outlet ng located on your VeriPure® System. Replace
the 3/8" red locking clip.
Step 9: Thread the power supply into the power jack located on your VeriPure® System. Plug the power supply into the
electrical outlet.
MOUNTING PLATE
WALL MOUNTED EXAMPLE POWER PLUGGED INTO POWERJACK
THESE 3 HOLES USE TO MOUNT PLATE TO WALL
SCREW ON EACH END OF
MOUNTING PLATE USED
TO FASTEN VERIPURE®
SYSTEM TO PLATE
10
VPC5000 COUNTER TOP INSTALLATION INSTRUCTIONS
Your VeriPure® System oers the opon of quick counter top installaon.
Cauon: Please be aware that your VeriPure® System CANNOT BE SUBMERGED IN WATER. Extra care should
be taken when choosing the counter top locaon for your VeriPure® System so that it will not get wet or
accidentally knocked into a sink or water basin.
Step 1: Place your VeriPure® System on a counter on the le side of your sink. There are only two possible
orientaons for the VeriPure® System to sit on a counter top (see photos on page 11).
Step 2: Remove the 3/8” clip from the 3/8 outlet on the Veripure® System.
Step 3: Insert the 3/8 tube into the VeriPure® System outlet unl fully seated, Replace red 3/8” locking clip
Step 4: Insert the 1/4” stem adapter ng into the lter cartridge.
Step 5: Posion the handle of the diverter valve in your preferred locaon and then hand ghten the diverter valve
collar.
Step 6: Connect power cord to the VeriPure System and plug into wall outlet.
Step 7: To operate your VeriPure System turn on your faucet, COLD WATER ONLY and turn the diverter valve handle.
Your VeriPure System will automacally turn on as water ows through it (veried by green unit on light on LED
readout). Flush the lters for 10 minutes as directed and check for leaks.
Note: See Flushing Instrucons Below.
FLUSHING INSTRUCTIONS
• TURN ON THE WATER SUPPLY AND FLUSH NEW CARTIDGES FOR 10 MINUTES, RUNNING
WATER THROUGH THE SYSTEM
• NEW FILTER ASSEMBLIES MAY CONTAIN “CARBON FINES” AND THE WATER MAY BRIEFLY
APPEAR GRAY, BUT WILL QUICKLY DISAPPEAR ONCE FLUSHED.
• IMPORTANT– CHECK THAT ALL WATER LINES ARE SECURE AND FIRMLY SEATED WITH NO
EVEIDENCE OF WATER LEAKAGE. IF A LEAK IS DETECTED, SHUT OFF WATER SUPPLY AND
DISCONNECT LINES AND VISUALLY CHECK FOR ANY DEFECTS AT THE END OF LINES. INSERT
LINES BACK IN UNTIL FULLY SEATED AND TURN WATER SUPPLY BACK ON. RECHECK FOR
ANY LEAKS.
Tabla de contenidos
Otros manuales de Sistema de agua de VERIPURE
Manuales populares de Sistema de agua de otras marcas
Spirotech
Spirotech SPIROVENT SUPERIOR S250 Manual de usuario
Culligan
Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manual de usuario
A.O. Smith
A.O. Smith Dura-Max AJH - 1000A - P Manual de usuario
Microline
Microline T.F.C.-4 Manual
Eureka Forbes
Eureka Forbes Aquaguard Select Manual de usuario
Cetetherm
Cetetherm AquaEfficiency Manual de usuario
