VERIPURE VERIPUREVP5000 Manual de usuario

REVISED 4/13/2020

OWNERS MANUAL VERIPUREVP5000

2425 HUTSON ROAD

GREEN BAY WI, 54303

(920) 613-6771

www.veripure.com

THANK YOU FOR CHOOSING VERIPURE®

PLEASE TAKE A FEW MOMENTS TO FILL IN THE INFORMATION BELOW, SAVE THIS

MANUAL AS A CONVENIENT INFORMATION SOURCE FOR YOUR VERIPURE® SYSTEM.

Date of Purchase:

Purchased From:

Phone Number:

Serial Number:

Installed By:

Dealer Name:

Dealer Phone

PERFORMANCE DATA SHEET

Model VPC5000 & Model VP5000

This system has been tested by WQA according to NSF/ANSI 42 and 53 for the reducon of the substances

listed below. The concentraon of the indicated substances in water entering the system was reduced to a

concentraon less than of equal to the permissible limit for water leaving the system, as specied in NSF/

ANSI 42 and 53. While tesng was performed under standard laboratory condions, actual performance

may vary. Do not use with water that is microbiologically unsafe or of unknown quality without adequate

disinfecon before or aer the system. Systems cered for cyst reducon may be used on disinfected

waters that may contain lterable cysts.

Stage One — Filtraon Process:

The VeriPure Maintenance Kit- Consists of a two lter conguraon that is a proprietary design of VeriPure, Inc. The rst lter

is a sediment lter that greatly reduces suspended and parculate maer from the incoming water source. The second lter

(a carbon block lter for cyst removal, lead and chlorine reducon) greatly reduces free chlorine and cysts from the water

source to disinfect and improve the taste and odor of the water.

Carbon Block Filter Data

Operang Specicaons:

Capacity: 1 ,250 Gallons Lead Reducon

Flow Rate: 0.50 to 1.0 GPM

Minimum Pressure: 50 PSI

Maximum Pressure: 125 PSI

Temperature: 35-90 F (2-32 C)

Parameter

Chlorine >=50%

Cyst >=99.95%

Lead 0.01 mg/L

IMPORTANT SAFEGUARDS AND PRECAUTIONS

 INSTALL YOUR VERIPURE® SYSTEM IN COMPLIANCE WITH STATE AND LOCAL LAWS AND REGU-

LATIONS FOR PLUMBING AND ELECTRICAL CODES. AS WITH ANY WATER DEVICE, PLEASE

CHECK YOUR SYSTEM FOR LEAKS ON A REGULAR BASIS. CONTACT A PLUMBER IMMEDIATELY

 VERIPURE® PERFORMANCE IS BASED UPON INPUT WATER WHICH MEETS MINIMUM EPA NA-

TIONAL PRIMARY AND SECONDARY DRINKING WATER STANDARDS.

 SEE WWW.EPA.GOV/DWSTANDARDSREGULATIONS



ATTENTION: THIS UNIT IS DESIGNED FOR TREATMENT OF COLD WATER ONLY.

READ INSTRUCTIONS- ALL SAFETY AND OPERATING INSTRUCTIONS SHOULD BE READ BEFORE THE UNIT IS OPERATED.

 RETAIN INSTRUCTIONS– SAFETY AND OPERATING INSTRUCTIONS SHOULD BE KEPT IN AN ACCESSIBLE LOCATION

FOR FUTURE REFERENCE.

 FOLLOW INSTRUCTIONS– ALL INSTRUCTIONS SHOULD BE FOLLOWED FOR MAINTAINING AND OPERATING YOUR

VERIPURE® SYSTEM PROPERLY.

 MAINTENANCE PRECUATIONS– ALWAYS TURN OFF THE WATER SUPPLY AT THE SINK OR WATER SOURCE AND UN-

PLUG POWER JACK FROM THE VERIPURE® SYSTEM BEFORE PERFORMING ANY MAINTENANCE.

 ACCESSORIES– DO NOT USE ANY ACCESSORIES, INCLUDING FILTER CARTRIDGES THAT ARE NOT RECOMMENDED

BY VERIPURE®

 WATER AND MOISTURE– DO NOT ALLOW MOISTURE TO CONTACT ANY INTERNAL OR EXTERNAL ELECTRONIC

COMPONENTS. SHOULD A LEAK OCCUR, IMMEDIATELY SHUT OFF THE WATER SUPPLY AND CONTACT YOUR

DEALER OR DISTRIBUTOR FOR SERVICE.

 POWER SOURCES– YOUR VERIPURE® SYSTEM SHOULD ONLY BE OPERATED FROM THE TYPE OF POWER SOURCE

INDICATED ON YOUR AC ADAPTER. IF YOU ARE NOT CERTAIN OF THE TYPE OF POWER SUPPLY TO THE OUTLET

PLEASE CONSULT YOUR VERIPURE® DEALER OR POWER COMPANY. ALTERNATIVE POWER SUPPLY ADAPTERS FOR

VOLTAGES FOUND IN MANY COUNTRIES OUTSIDE THE UNITED STATES ARE AVAILABLE THROUGH YOUR DEALER

ON SPECIAL ORDER. YOUR VERIPURE® SYSTEM MAY ALSO BE OPERATED WITH A BATTERY PACK OR GENERTOR.

 POWER CORD PROTECTION– VERIPURE® RECCOMENDS THAT POWER SUPPLY CORDS SHOULD BE ROUTED SO

THAT THEY ARE NOT LIKELY TO BE WALKED ON OR PINCHED BY ITEMS PLACED UPON OR AGAINST THEM.

HOW YOUR VERIPURE® SYSTEM WORKS

YOUR PATENTED VERIPURE® SYSTEM HAS BEEN DESIGNED TO USE TWO STAGES OF PRIMARY FILTRATION

AND LOW LEVEL OZONE TECHNOLOGY®. OPERATIONAL MAINTENANCE AND REPLACEMENT REQUIREMENTS

ARE ESSENTIAL FOR THE VERIPURE® SYSTEM TO PERFORM TO SPECIFIATIONS. CONTACT YOUR LOCAL

DEALER OR DISTRIBUTOR FOR REPLACEMENT FILTERS AND PARTS, OR CONTACT VERIPURE FOR THE DEALER

NEAREST YOU. THE VERIPURE® SYSTEM IS RECCOMENDED TO BE CONNECTED TO MUNICIPAL WATER

SOURCES.

FOOD & SURFACES

GENERAL RECOMENDATIONS FOR USING OZONATED WATER ARE AS FOLLOWS-

 PLACE ITEM OR ITEMS TO BE WASHED UNDER A STEADY STREAM OF VERIPURE® WATER AND RINSE.

 FOOD PREPARATION: IT IS RECOMMENDED ITEMS BE RINSED FOR 3 MINUTES WITH VERIPURE® WATER.

 FOOD ITEMS: PLACE IN A BOWL, COLANDER OR STRAINER. RINSE WITH VERIPURE® WATER.

STORING WATER

 SELECT A CONTAINER THAT IS FOOD GRADE QUALITY, SUCH AS GLASS OR STAINLESS STEEL. THOROUGHLY RINSE

THE CONTAINER WITH VERIPURE® WATER AT LEAST TWICE. FILL THE CONTAINER TO WITHIN ONE TO TWO INCHES

FROM THE TOP AND REPLACE CAP.

 STORE WATER IN REFRIGERATOR AND MAKE CERTAIN THE CAP IS REPLACED AFTER EVERY USE.

 WHEN WATER IS FRESHLY OZONATED YOU MAY INITIALLY BE ABLE TO DETECT A SLIGHT HINT OF OZONE. PEOPLE

VARY IN THEIR SENSITIVITY TO OZONE. ANY HINT OF THE OZONE TASTE WILL DISAPPEAR WITHIN A SHORT PERIOD

OF TIME. YOUR SYSTEM PRODUCES MINIMAL WASTE WHILE PRESERVING MINERALS IN YOUR WATER.

IMPORTANT NOTE: VERIPURE® PERFORMANCE IS BASED UPON INPUT WATER WHICH MEETS MINIMUM

EPA NATIONAL PRIMARY AND SECONDARY DRINKING WATER STANDARDS.

SEE WWW.EPA.GOV/DWSTANDARDSREGULATIONS

A LOOK AT YOUR VERIPURE® SYSTEM

UNIT DIMENSIONS: 11.5”L X 7”W X 5.5”H 9.0LBS (4.05KG)

IT IS IMPORTANT TO BE FAMILIAR WITH CERTAIN COMPONENTS OF YOUR VERIPURE® SYSTEM FOR

MAINTENANCE PURPOSES.

DIAGRAM 1

INSTALLATION INSTRUCTIONS

BEFORE INSTALLING

1. YOUR VERIPURE® SYSTEM IS DESIGNED TO BE USED WITH COLD WATER ONLY.

2. NEVER RUN WARM OR HOT WATER THROUGH YOUR VERIPURE® SYSTEM AS HOT WATER

CAN DAMAGE THE CARBON BLOCK FILTER.

3. WATER TEMPERATURES ABOVE 90° F CANNOT CONTAIN DISSOLVED OZONE; THUS

ELIMINATING DISINFECTION. WATER TEMPS APPROACHING 85° F REQUIRE LONGER

PERIODS OF CONTACT TIME FOR DISINFECTION PURPOSES.

4. FOR OPTIMAL PERFORMANCE , LIMIT YOUR VERIPURE® SYSTEM TO 70 PSI OF WATER

PRESSURE. VERIPURE® RECOMMENDS A MINIMUM WATER PRESSURE OF 50 PSI. LOW

WATER PRESSURE WILL CAUSE YOUR VERIPURE® SYSTEM TO PRODUCE A LOWER

QUANTITY OF FILTERED AND OZONATED WATER.

5. POWER REQUIREMENTS ARE 120 VAC 60 HZ. USE AC ADAPTER PROVIDED WITH YOUR

SYSTEM.

NOTE: VERIPURE® UNITS ARE DESIGNED TO BE UNDER CONTINUAL WATER PRESSURE WHEN

INSTALLED AND NOT IN USE, THE ON/OFF VALVE AND OR FAUCET SHOULD BE ON THE

OUTLET OF THE VERIPURE AT OR BETWEEN THE POU AND VERIPURE® UNIT. THIS ENSURES

PROPER FUNCTION ON THE VERIPURE® .

 VP5000 INSTALLATION INSTRUCTIONS BEGIN ON NEXT PAGE (PAGE 8)

VP5000 INSTALLATION INSTRUCTIONS

 UNDER THE COUNTER MODEL

 DUE TO VARIANCE IN PLUMBING AND POWER OUTLETS; WE RECOMMEND THAT A PLUMBER AND OR

ELECTRICIAN INSTALL YOUR VERIPURE® SYSTEM BY FOLLOWING THESE INSTALLATION INSTRUCTIONS. IF YOU

CHOOSE TO INSTALL THE UNIT YOURSELF PLEASE CALL (800)525-9718 FOR ASSISTANCE.

 INSTALLATION OF THE VERIPURE® SYSTEM MUST CONFORM TO STATE AND LOCAL PLUMBING AND ELECTRICAL

CODES, LAWS, AND REGULATIONS AND THE INSTRUCTIONS PROVIDED WITH YOUR VERIPURE® SYSTEM. FAILURE

TO INSTALL AS INSTRUCTED WILL VOID THE WARRANTY.

NOTE: YOU MAY HAVE AN EXISTING POWER OUTLET UNDER THE SINK TO POWER A GARBAGE DISPOSAL. TYPICALLY,

THERE IS ONLY POWER TO THIS OUTLET WHEN THE SWITCH FOR THE DISPOSAL IS TURNED ON. IF THIS IS THE CASE AN

ELECTRICIAN WILL NEED TO INSTALL AN ADDITIONAL POWER OUTLET.

PLEASE CHECK YOUR VERIPURE® SYSTEM TO BE CERTAIN ALL ITEMS LISTED BELOW ARE INCLUDED.

 QTY 1 AC ADAPTER (POWER SUPPLY) WITH OUTLET PLUG

 QTY 1 FAUCET ASSEMBLY

 QTY 1 FAUCET MANUFACTURES INSTRUCTION SHEET

 QTY 1 3/8” TUBING 4’ IN LENGTH (OUTLET HOSE TO FAUCET)

 QTY 1 1/4” TUBING 4’ IN LENGTH WATER SUPPLY TO FILTER INLET

 QTY 1 ANGLE STOP ADAPTER ON/OFF TEE

 QTY 1 MOUNTING PLATE

 QTY 1 OWNERS MANUAL

 QTY 3 MOUNTING SCREWS

 QTY 1 SPANNER TOOL

 QTY 2 RUBBER FEET

 QTY 1 HEX WRENCH

FAUCET INSTALLATION INSTRUCTIONS

VERIPURE® RECCOMENDS THAT THE LOCATION OF THE FAUCET HOLE BE DETERMINED AT THE TIME OF

INSTALLATION. MOST KITCHEN SINKS ARE EQUIPPED WITH A THIRD FAUCET OPENING LOCATED TO THE RIGHT OF THE

MAIN FAUCET. USUALLY THIS OPENING IS USED FOR A SPRAYER AND IS THE MOST COMMON CHOICE FOR THE

VERIPURE® SYSTEM FAUCET.

***DUE TO VARIANCES IN COUNTER TOP MATERIALS AND SINK DESIGN, WE RECOMMEND USING A CERTIFIED

PLUMBER FOR YOUR FAUCET INSTALLATION.

FAUCET OPENING

INSTALLING THE VERIPURE® SYSTEM FAUCET TO THE RIGHT SIDE OF THE COLD WATER SIDE IS PREFERABLE.

IT IS RECOMMENDED THAT IF DRILLING A NEW OPENING, THE OPENING BE COMPLETED AT THIS TIME.

VP5000 INSTALLATION INSTRUCTIONS (CONTINUED)

 UNDER THE COUNTER MODEL

STEP 1: PLEASE INSPECT YOUR VERIPURE® SYSTEM GLASS DIELECTRIC TUBE AT THIS TIME. LOCATE THE

KNOB ON YOUR VERIPURE® SYSTEM. TURN 1/4 COUNTER CLOCKWISE AND PULL STRAIGHT OUT VERY

CAREFULLY. INSPECT THE DIELECTRIC FOR ANY CRACKS OR BREAKAGE THAT MAY HAVE OCCURRED IN

SHIPPING. IF NO DEFECTS ARE FOUND THEN GENTLY REPLACE DIELECTRIC. WHEN REPLACING

DIELECTRIC, TURN 1/4 CLOCKWISE TO LOCK IN PLACE.

STEP 2: LOCATE THE POWER OUTLET FOR THE POWER SUPPLY.

STEP 3: SHUT OFF THE COLD WATER SUPPLY UNDER THE SINK OR FROM THE MAIN SOURCE.

STEP 4: REMOVE THE COLD WATER FEED LINE TO THE FAUCET FROM THE COLD WATER SUPPLY VALVE.

STEP5: THREAD THE FEMALE THREADED END OF THE ANGLE STOP TEE TO THE COLD WATER SUPPLY VALVE.

STEP6: THREAD THE COLD WATER FEED LINE INTO THE MALE THREADED END OF THE ANGLE STOP TEE.

STEP 7: LOCATE THE BEST AREA FOR HANGING THE VERIPURE® SYSTEM. ( MAKE CERTAIN THE INLET

ASSEMBLY AND OUTLET TO FAUCET HOSES AND THE POWER SUPPLY CORD ARE LONG ENOUGH WHEN

SELECTING THIS LOCATION.)

STEP 8: MOUNT SCREWS FOR THE VERIPURE® SYSTEM BY USING THE PROVIDED SCREWS AND TEMPLATE.

STEP 9: MOUNT YOUR VERIPURE® SYSTEM ONTO THE MOUNTING SCREWS PREVIOUSLY INSTALLED.

STEP 10: INSTALL YOU VERIPURE® SYSTEM FAUCET AT THIS TIME.

 USE ONLY THE FAUCET SUPPLIED WITH YOUR VERIPURE® SYSTEM!

 DUE TO VARIANCES IN COUNTER TOP MATERIALS AND SINK DESIGN, WE RECOMMEND USING A

CERTIFIED PLUMBER FOR YOUR FAUCET INSTALLATION.

 ONCE YOUR FAUCET IS SECURELY IN PLACE, THREAD THE 7/16” FEMALE END OF THE 3/8” X 7/16”

STRAIGHT FAUCET FITTING ONTO THE THREADED END OF THE FAUCET UNDER THE SINK.

 NOW ITS TIME TO CONNECT HOSES AND FITTINGS USING THE QUICK CONNECTIONS . SEE FOLLOWING

TUTORIAL. (PAGE 10)

VP5000 INSTALLATION INSTRUCTIONS (CONTINUED)

 UNDER THE COUNTER MODEL

CONNECTING STANDARD PUSH-IN FITTINGS

 PUSH UP TO TUBBING STOP

 PUSH THE TUBBING INTO THE FITTING, TO THE TUB-

BING STOP. THE COLLET (GRIPPER) HAS STAINLESS

STEEL TEETH WHICH HOLD THE TUBBING FIRMLY IN

POSITION WHILE THE O-RING PROVIDES A

PERMANENT LEAK PROOF SEAL.

 PULL ON THE TUBBING TO CHECK THAT IT IS SECURE. A

GOOD PRACTICE IS TO TEST THE SYSTEM PRIOR TO LEAV-

ING THE SITE AND/OR BEFORE USE.

DISCONNECTING STANDARD PUSH-IN FITTINGS

 ENSURE THE SYSTEM IS DEPRESSURIZED BEFORE RE-

MOVING FITTINGS. PUSH IN THE COLLET AGAINST THE

FACE OF THE FITTING. WITH THE COLLET HELD IN THIS

POSITION THE TUBBING CAN BE REMOVED. THE FITTING

CAN THEN BE RE-USED.

STEP 11: CONNECT THE 1/4” WHITE TUBBING TO THE ANGLE STOP TEE. MAKE SURE WHITE TUBBING IS

FULLY SEATED INTO FITTING.

STEP 12: CONNECT THE OPPOSITE END OF THE 1/4” WHITE TUBBING TO THE FILTER INLET ELBOW. MAKE

SURE WHITE TUBBING IS FULLY SEATED INTO FITTING.

STEP 13: REMOVE THE RED LOCKING CLIP FROM THE 3/8” X 7/16” STRAIGHT FITTING THAT WAS

PREVIOUSLY ATTACHED TO THE THREADED PORTION OF THE FAUCET. INSERT ONE END OF THE PROVIDED

3/8” WHITE TUBBING. REPLACE RED LOCKING CLIP AFTER TUBBING HAS BEEN FULLY SEATED.

STEP 14: REMOVE THE RED LOCKING CLIP FROM VERIPURE® UNIT OUTLET. INSERT THE OTHER END OF THE

3/8” WHITE TUBBING INTO THE OUTLET SIDE OF THE VERIPURE® UNIT. REPLACE RED LOCKING CLIP AFTER

TUBBING HAS BEEN FULLY SEATED.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de agua de VERIPURE

VERIPURE

VERIPURE VERIPUREVPC7000 Manual de usuario

VERIPURE

VERIPURE VERIPUREVPC5000 Manual de usuario

Manuales populares de Sistema de agua de otras marcas

Spirotech

Spirotech SPIROVENT SUPERIOR S250 Manual de usuario

Culligan

Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manual de usuario

A.O. Smith

A.O. Smith Dura-Max AJH - 1000A - P Manual de usuario

Microline

Microline T.F.C.-4 Manual

Eureka Forbes

Eureka Forbes Aquaguard Select Manual de usuario

Cetetherm

Cetetherm AquaEfficiency Manual de usuario

CB Tech

CB Tech CB-VOC Manual de usuario

Vaillant

Vaillant auroFLOW plus VPM 15 D Manual de usuario

resideo

resideo Braukmann HS10S Manual de usuario

Gude

Gude INOX 100/24 Manual de usuario

Mono

Mono Eco 1-60 Manual

SpectraPure

SpectraPure Drinking Water Kit Manual de usuario

HydroCare

HydroCare Dual Action Manual de usuario

NEXT pool

NEXT pool STERILOR Cu/Ag Diagrama de cableado

Alpha

Alpha SolarSmart 150 Guía del usuario

TA FRISTAR3 Manual de usuario

GÜDE

GÜDE HWA 800 K Manual de usuario

Rainfresh

Rainfresh UCS2 Manual de usuario