Vent-Axia MULTIVENT MV250 Instrucciones de montaje

PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH THE ILLUSTRATIONS.

PLEASE SAVE THESE INSTRUCTIONS

MULTIVENT

MV250

MEV Unit

Stock Ref. N°

MV250 181510C

Installation and Wiring Instructions

220-240V~50Hz

IP22

Installation and Wiring Instructions for the Multivent Extract Fan.

IMPORTANT:

READ THESE INSTRUCTIONS BEFORE COMMENCING THE

INSTALLATION

DO NOT install this product in areas where the following may be present or occur:

•Excessive oil or a grease laden atmosphere.

•Corrosive or flammable gases, liquids or vapours.

• Ambient exhaust air temperatures higher than 40°C or less than –5°C.

•Relative humidity above 90%

• Possible obstructions which would hinder the access or removal of the Unit.

•Sudden ductwork bends or transformations close to the Unit.

SAFETY AND GUIDANCE NOTES

A. All wiring must be in accordance with the current I.E.E. Regulations, or the appropriate

standards of your country.

B. The Unit should be provided with a local double pole isolator switch having a contact

separation of at least 3mm. The fuse rating should be 3A.

C. Ensure that the mains supply (Voltage, Frequency and Phase) complies with the rating

label.

D. The Unit should only be used in conjunction with the appropriate Vent-Axia products.

E. It is recommended that the connection to the terminal box is made with flexible

cable/conduit.

F. The Unit should not be sited within 600mm horizontally of/or 2250mm vertically of a

bath/shower tray, in accordance with the current I.E.E. Regulations for bathrooms.

G. When the unit is used to remove air from a room containing a fuel-burning appliance,

ensure that the air replacement is adequate for both the fan and the fuel-burning

appliance.

H. The installer must ensure that the Unit intake is located a minimum of 600mm from any

flue outlet.

I. This Unit is designed as an inline ducted unit to be positioned between lengths of

ducting. Short duct runs terminating within 1.5m must incorporate suitable guards

unless the unit is mounted higher than 2.3m.

J. This Unit should not be used where it is liable to be subject to direct water spray from

hoses etc.

K. This Unit handles moisture-laden air, ensure that a condensation drain is fitted.

L. This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory and mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning the use of the appliance

in a safe way and understand the hazards involved.

M.Children shall not play with the appliance.

N. Certain applications may require the installation of sound

attenuation material to achieve the sound levels required.

O. Ducted ventilators must be ducted to the outdoors.

TYPICAL INSTALLATION

INTRODUCTION NOTES

The MULTIVENT is designed for simultaneous ventilation for a maximum of up to four separate areas such

as bathrooms, kitchens and toilets. The range can be mounted in three different orientations for convenient

installation in roof voids with a height of 250mm or greater. The MV250 employs a highly efficient backward

curved centrifugal motor impeller set. It is designed for continuous 24-hour use and should not be used in

conjunction with a delay timer.

This product must be installed in accordance with the Domestic Ventilation Compliance Guide (England and

Wales).

SITING

It is the responsibility of the installer to ensure that all aspects of system design are taken into

consideration.

MULTIVENT is designed as a ducted unit and should only be used in ducted applications. Short duct runs,

terminating

close to the fan (i.e. within 1.5m), must incorporate suitable guards. Between two and four intake ducts may

be used, three on the case sides and one in the base.

The MULTIVENT may be mounted in three orientations.

a). Base mounted Installation with ducting radiating out horizontally. The Condensate Drain is on the

opposite side to the exhaust spigot at the base of the unit.

CondensateDrain

On the unit housing.

b). Vertically mounted Installation with the exhaust spigot at top. The Condensate Drain is opposite to the

exhaust spigot at the base of the unit. Additional drainage may be required from the duct connected to the

bottom spigot.

Condensate Drain

On the unit housing.

c). Ceiling mounted Installation. The Condensate Drain is opposite to the exhaust spigot under the lid of

the unit. Additional drainage may be required.

Condensate Drain

Underthelid.

See the dimensional details below for the mounting hole positions.

INSTALLATION

1. Position the MULTIVENT, taking into consideration the position of the rooms to be ventilated, the

exhaust position, the drainage position and the electrical services. Ensure there is adequate access for

installation and maintenance. Securely mount the MULTIVENT through the mounting brackets on the

casing using the appropriate anti-vibration mounts, screws, washers, rubber bushes etc.

2. Where the intake and exhaust ducts are to be connected to the MULTIVENT, remove the spigot caps, if

125mm ducting is being used. If 100mm ducting is being used, peel out the centre of the cap with a

screwdriver as indicated and leave the cap surround in position. To connect ducting to the base intake,

use a suitable adaptor attached using the 4 holes provided.

3. Ducting passing through an unheated roof void should be insulated. Ducting runs should be as straight

as possible and intake ducting should slope downwards from Under the lid. Connect ducting to the

MULTIVENT spigots and to appropriate ceiling terminations.

4. Select the drain spigot required, remove the “Knockout” and connect a suitable drainage system.

Condensate drain

On the unit housing

Condensate drain

Under the lid

WIRING

WARNING: THE MULTIVENT AND ANCILLARY CONTROL EQUIPMENT MUST BE

ISOLATED FROM THE POWER SUPPLY DURING THE INSTALLATION / OR

MAINTENANCE.

THE MULTIVENT UNIT MUST BE EARTHED.

Access to the MULTIVENT connection terminals is under the top cover which is retained by four screws.

Ensure that the mains supply voltage, frequency, number of phases and power rating comply with the details

on the rating label positioned under the top cover.

All wiring must be in accordance with local and/or national electrical codes as applicable or the appropriate

standard in your country (BS7671 in the UK). The MULTIVENT must be supplied through a double-pole

isolating switch, having a contact separation of not less than 3mm. Cable clamps are provided for use with the

cable or flex on entry into the MULTIVENT.

To meet the stated energy efficiency rating, the Multivent MV250 range should be connected so that it

can run at all three speeds, with to at least two sensor inputs. A possible wiring arrangement is shown in

Figure 2.

Fig.1.

Power connection for speed selection

Fig.2.

Example wiring for 3 speeds with three external sensors

OVER-HEATING PROTECTION

The MULTIVENT motor is fitted with Standard Thermal Overload Protection. This will automatically switch

the fan Off in the event of a fault condition.

If this occurs isolate the MULTIVENT, check for and remove any obstruction, leave for a short time for the

motor to cool before reconnecting. If this recurs, Isolate the MULTIVENT and call a service engineer.

PRODUCT FICHE

For Residential Ventilation Units (Complying Commission Delegated Regulation (EU)

No 1254/2014)

Name: Vent‐Axia

ModelID(StockRef.):MV250‐181510‐LDC

SECClassC

SECValue('Average')‐25.71

SECValue('Warm')‐10.21

SECValue('Cold')‐52.78

LabelRequired?(Yes/No=Outofscope)Yes

Declaredas:RVUorNRVU/UVUorBVURVU/UVU

SpeedDriveMulti‐Speed

TypeHRS(Recuperative,Regenerative,None)None

ThermalEff:[(%),NA(ifnone)]N/A

Max.FlowRate(m3/h)489.6

Max.PowerInput(W):(@Max.FlowRate)63.3

LWA:SoundPowerLevel(dB)51.53

Ref.FlowRate(m3/s)0.10

Ref.PressureDiff.(Pa)185

SPI[W/(m3/h)]0.16

ControlFactor&ControlTypology:(CTRL/Typology)

ControlFactor;CTRL0.65

ControlTypologyLocalDemandControl

Declared:‐MaxInternal&ExternalLeakageRates(%)forBVUsor

carryover(forregenerativeheatexchangersonly),

‐&Ext.LeakageRates(%)forDuctedUVUs;

<5%Internal,<5%External

MixingRateofNon‐DuctedBVUsnotintendedtobeequipped

withoneductconnectiononeithersupplyorextractairside;N/A

PositionanddescriptionofvisualfilterwarningforRVUsintended

forusewithfilters,includingtextpointingouttheimportanceof

regularfilterchangesforperformanceandenergyefficiencyof

theunit

N/A

ForUVUs(InstructionsInstallRegulatedSupply/ExtractGrilles

Façade)InF&W

InternetAddress(forDisassemblyInstructions)www.vent‐axia.com

Sensitivityp.Variation@+20/‐20Pa:(forNon‐DuctedVUs)N/A

AirTightness‐ID/OD‐(m3/h)(forNon‐DuctedVUs)N/A

AnnualElectricityConsumption:AEC(kWh/a)1.03

AnnualHeatingSaved:AHS(kWh/a)

AHS:Average28.30

AHS:Warm12.80

AHS:Cold55.36

Disposal

This product should not be disposed of with household waste. Please recycle where

facilities exist. Check with your local authority for recycling advice.

Head Office: Fleming Way, Crawley, West Sussex, RH10 9YX. Tel: 01293 526062 Fax: 01293 551188

UK NATIONAL CALL CENTRE, Newton Road, Crawley, West Sussex, RH10 9JA

SALES ENQUIRIES: Tel: 0844 8560590 Fax: 01293 565169 Email:- [email protected]

TECHNICAL SUPPORT: Tel: 0344 8560594 Fax: 01293 532814 Email:- [email protected]

Web:- www.vent-axia.com Email:- [email protected]

As part of the policy of continuous product improvement Vent-Axia reserves the right to alter specifications without notice.

407445D 1217

The Guarantee

Applicable only to products installed and used in the United Kingdom. For details of guarantee outside the United Kingdom contact your local

supplier.

Vent-Axia guarantees its products for two years from date of purchase against faulty material or workmanship. In the event of any part being found

to be defective, the product will be repaired, or at the Company’s option replaced, without charge, provided that the product:-

Has been installed and used in accordance with the instructions given with each unit.

Has not been connected to an unsuitable electricity supply. (The correct electricity supply voltage is shown on the product rating label

attached to the unit).

Has not been subjected to misuse, neglect or damage.

Has not been modified or repaired by any person not authorised by the company.

IF CLAIMING UNDER TERMS OF GUARANTEE

Please return the complete product, carriage paid to your original supplier or nearest Vent-Axia Centre, by post or personal visit. Please ensure

that it is adequately packed and accompanied by a letter clearly marked “Guarantee Claim” stating the nature of the fault and providing evidence of

date and source of purchase.

The guarantee is offered to you as an extra benefit, and does not effect your legal rights

Otros manuales para MULTIVENT MV250

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de Vent-Axia

Vent-Axia

Vent-Axia QPTW Series Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon Responce Series Instrucciones de montaje

Vent-Axia

Vent-Axia HR100R Guía del usuario

Vent-Axia

Vent-Axia JUPITER315 Instrucciones de montaje

Vent-Axia

Vent-Axia Centrif Duo Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon iQ Manual de usuario

Vent-Axia

Vent-Axia Lo-Carbon PureAir Home Series Instrucciones de montaje

Vent-Axia

Vent-Axia VA 140 X Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon NBR dMEV C Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus Series Instrucciones de montaje

Vent-Axia

Vent-Axia Slimpak EC Series Instrucciones de montaje

Vent-Axia

Vent-Axia MVDC-MS Instrucciones de montaje

Vent-Axia

Vent-Axia Svensa Manual de usuario

Vent-Axia

Vent-Axia ACM315 Instrucciones de montaje

Vent-Axia

Vent-Axia NBR dMEV C 100 T Instrucciones de montaje

Vent-Axia

Vent-Axia HR100W Guía del usuario

Vent-Axia

Vent-Axia Centrif Duo Series Instrucciones de montaje

Vent-Axia

Vent-Axia Centra Lo-Carbon SELV Series Instrucciones de montaje

Vent-Axia

Vent-Axia Azur 100B Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon Revive Series Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus SELV Series Instrucciones de montaje

Vent-Axia

Vent-Axia GALAXY GDD Series Guía de solución de problemas

Vent-Axia

Vent-Axia SVARA Manual de usuario

Vent-Axia

Vent-Axia 405215 Advance S Guía

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje