Venstar T2150 Instrucciones originales

Owner’s Manual

& Installation

Instructions

7 Day Programmable •Fan Coil Control

with

Wi-Fi

and local

API

FAN COIL THERMOSTAT

COMMERCIAL MODEL T2150

TheT2150 can be used to replace any of the following thermostats.

No re-wiring or backplate change should be required.

Venstar, Inc

T1070 Non-programmable**

T1075 programmable

Carrier, Corp

33CSSN2-FC* Non-programmable**

33CSSP2-FC* programmable

International Environmental Corp

E055-71308102*, E055-71520301, E055-71520304

E055-71308115*, E055-71520316, E055-71520318 Non-programmable**

E055-71308103*, E055-71520302, E055-71520305

E055-71308116*, E055-71520317, E055-71520319 programmable

Johnson Controls

T701DFN-1,T701DFN-2,T701DFN-3,T701DFN-4 Non-programmable**

T701DFP-1, T701DFP-2,T701DFP-3, T701DFP-4 programmable

* : setup step 20 (Fan Coil Type) should be set to ‘SPECIAL’ for 33ZCRLYBRD

** : setup step 4 (PROG) should be set to ‘NO’

Note : TheT2150 uses a different remote temperature sensor than the

models shown so if a remote sensor had been in use, it should be

replaced with a ACC-DSEN.

Follow the Installation Instructions before proceeding. Set the

thermostat mode to “OFF” prior to changing settings in setup

or restoring Factory Defaults.

CAUTIO

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules.These limits are designed

to provide reasonable protection against harmful interference in a residential

installation.This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

of the receiver.

• Consult the dealer or an experienced radio or TV technician for help.

Notice: Only peripherals complying with FCC limits may be attached to this

equipment. Operation with noncompliant peripherals or peripherals not

recommended by Venstar, is likely to result in interference to radio and TV

reception. Changes or modiﬁcations to the product, not expressly approved by

Venstar could void the user’s authority to operate the equipment.

FCC - INDOOR Mobile Radio Information:

To comply with FCC/IC RF exposure limits for general population / uncontrolled

exposure, the antenna(s) used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be co-located

or operating in conjunction with any other antenna or transmitter.

This Device complies with Industry Canada License-exempt RSS standard(s).

Operation is subject to the following two conditions: 1) this device may not

cause interference, and 2) this device must accept any interference, including

interference that may cause undesired operation of the device.

This Mini thermostat has the ability to receive updates to its ﬁrmware.

Periodically ﬁrmware updates are released by the manufacturer to add features

and/or performance enhancements.This manual was produced reﬂecting the

most current ﬁrmware/feature set at the time of publication, ﬁrmware rev. 1.0.

Firmware releases after rev. 1.0 may not be adequately depicted in this manual.

Please refer to the appropriate website or contact your place of purchase to learn

about changes to the thermostat after ﬁrmware release 1.0.

Under Industry Canada regulations, this radio transmitter may only operate using

an antenna of a type and maximum (or lesser) gain approved for the transmitter

by Industry Canada.To reduce potential radio interference to other users, the

antenna type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that necessary for successful

communication.

Cet appareil est conforme avec Industrie Canada, exempts de licence standard

RSS(s). Son fonctionnement est soumis aux deux conditions suivantes: 1) ce

dispositif ne doit pas causer d’interférences, et 2) ce dispositif doit accepter

toute interférence, y compris les interférences qui peuvent causer un mauvais

fonctionnement de l’appareil.

En vertu des règlements d’Industrie Canada, cet émetteur de radio ne peut

fonctionner en utilisant une antenne d’un type et maximale (ou moins) Gain

approuvé pour l’émetteur par Industrie Canada. Pour réduire les interférences

radio potentielles aux autres utilisateurs, le type d’antenne et son gain doivent

être choisis aﬁn que la puissance isotrope rayonnée équivalente (PIRE) ne est pas

plus de ce qui est nécessaire pour une communication réussie.

We, Venstar, declare under our sole responsibility that the device to which

this declaration relates: Complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC ID: MUH-SKYPORT8

IC: 12547A-SKYPORT8

Innovation, Science and Economic Development Canada

ICES-003 Compliance Label: CAN ICES-3 (B)/NM8-3(B)

Table of Contents

Installation Instructions.................................................................................1

Thermostat Backplate ..............................................................................2

Wire Connections......................................................................................3

Connect to Wi-Fi..............................................................................................5

Front Panel........................................................................................................8

Display...............................................................................................................9

Basic Operation.............................................................................................11

User Setup Steps ...........................................................................................13

Time of day, day of week, clock ........................................................14

Backlight Operation.............................................................................15

System Type...........................................................................................16

Deadband Settings...............................................................................17

Setpoint Limits ......................................................................................18

Override time.........................................................................................19

Temperature units.................................................................................19

Fan Coil Operation................................................................................19

Fan Operation & Sensor Use ..............................................................20

Dry Contact ............................................................................................22

Service Filter.........................................................................................23

Skyport and Local API .........................................................................24

Keypad Lock ...................................................................................................25

Programming a Daily Schedule..................................................................26

About Advanced Features & Operation.....................................................28

Advanced Setup Table..................................................................................31

Follow Installation Instructions carefully. Disconnect

Power to the Heater/Air Conditioner before removing

the old thermostat and installing the new thermostat.

CAUTION

IMPORTANT

iii

Auto-Changeover: A mode in which the thermostat will turn on the

heating or cooling based on room temperature demand.

Cool Setpoint: The warmest temperature that the space should rise

to before cooling is turned on (without regard to deadband).

Deadband: The number of degrees the thermostat will wait, once a

setpoint has been reached, before energizing heating or cooling.

Differential: The forced temperature difference between the heat

setpoint and the cool setpoint.

Heat Setpoint:The coolest temperature that the space should drop

to before heating is turned on (without regard to deadband).

Icon: The word or symbol that appears on the thermostat display.

Mode: The current operating condition of the thermostat (i.e. Off,

Heat, Cool, Auto, Program On).

Non-Programmable Thermostat: A thermostat that does not have the

capability of runningTime Period Programming.

Programmable Thermostat: A thermostat that has the capability of

runningTime Period Programming.

Pre-Occupancy Purge: Fan operation prior to Occupied 1.

Temperature Swing: Same as Deadband.

Time Period Programming: A program that allows the thermostat

to automatically adjust the heat setpoint and/or the cool setpoint

based on the time of the day.

Glossary of Terms

Installation Instructions

Remove and Replace the old thermostat

To install the thermostat properly, please follow these step by step

instructions. If you are unsure about any of these steps, call a qualiﬁed

technician for assistance.

• Installation tools: Small ﬂat blade screwdriver, Phillips screwdriver,

wire cutters and wire strippers.

• Make sure your Heater/Air Conditioner is working properly before

beginning installation of the thermostat.

• Carefully unpack the thermostat. Save the screws, any brackets,

and instructions.

• Turn off the power to the Heating/Air Conditioning system at the main

fuse panel. Most residential systems have a separate breaker or

switch for disconnecting power to the furnace.

• Remove the cover of the old thermostat. If it does not come off easily,

check for screws.

• Loosen the screws holding the thermostat base or subbase to the

wall and lift away.

• If you have a smart phone handy, take a photo of the wiring for

future reference.

• Disconnect the wires from the old thermostat. Tape the ends of the

wires as you disconnect them, and mark them with the letter of the

terminal for easy reconnection to the new thermostat.

• Keep the old thermostat for reference purposes, until your new

thermostat is functioning properly.

Installation Instructions

SCALE 1 : 1

The Explorer Mini Thermostat Backplate

RS Remote Sensor

R 24 VAC return

GLow speed fan relay

Y1 Cool

G3 High speed fan relay

W1 Heat

G2 Medium speed fan relay

C24 VAC common

H20 Water Temp. Changeover Sensor

CK1 Dry Contact

IMPORTANT: This thermostat requires both R (24 VAC Return) and C (24 VAC

Common) wires be connected to the backplate terminals to operate properly.

To remove the thermostat backplate:

Gently separate the display from the

base by pulling from the center.

H20

CK1

SCALE 1 : 1

Installation Instructions

Thermostat If 2-pipe with

auxiliary electric heat

Generic relay board

24vac24 volt

water

valve

H20 Changeover Sensor

(ACC-SENFC)

(closes below 60˚,

opens above 75˚)

Wiring Diagram

2-Pipe, Low Voltage Valve, H20 Changeover Sensor

H20

VEH

COM

Installation Instructions

SCALE 1 : 1

Thermostat

Connect directly to R

terminal on backplate

IMPORTANT NOTE:

If a duct sensor is

connected to this

thermostat it is

suggested that the fan

be programmed for

continuous operation

(Setup Step 16, page 18

of the Owner’s Manual)

Generic relay board

24vac24 volt

water

valves

Dry Contact

Duct Sensor

ACCDSEN

Wiring Diagram

4-Pipe, Low Voltage Valves, Duct

Temperature Sensor & Dry Contact

H20

CK1

G2(W)

G3(Y)

COM

GND

Tabla de contenidos

Otros manuales de Termostato de Venstar

Venstar

Venstar T2700 Manual de usuario

Venstar

Venstar T1050 Manual de usuario

Venstar

Venstar TSTATEZ Manual de usuario

Venstar

Venstar T2900SCH Manual de usuario

Venstar

Venstar T5900 Manual de uso y cuidado

Venstar

Venstar T0130 Manual de usuario

Venstar

Venstar ColorTouch T6900 Instrucciones de funcionamiento

Venstar

Venstar T1800 Manual de usuario

Venstar

Venstar TSTATCCPB501 Manual de usuario

Venstar

Venstar T4950SCH-IAQ Instrucciones de funcionamiento

Venstar

Venstar T1700 Manual de usuario

Venstar

Venstar TSTATEZ Manual de usuario

Venstar

Venstar EXLORER Mini Instrucciones originales

Venstar

Venstar T1800 Manual de usuario

Venstar

Venstar T2800 Manual de usuario

Venstar

Venstar T1035 Manual de usuario

Venstar

Venstar P474-1100RF Manual de usuario

Venstar

Venstar EXPLORER Manual técnico

Venstar

Venstar EXPLORER RESIDENTIAL T3950-IAQ Instrucciones de funcionamiento

Venstar

Venstar T1100FS Manual de usuario

Venstar

Venstar T1700 Manual de usuario

Venstar

Venstar T5900 Instrucciones de funcionamiento

Venstar

Venstar VOYAGER T4900 Manual de usuario

Venstar

Venstar T1045 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario