Velleman VM130 Manual de usuario

TWO CHANNEL RF REMOTE CONTROL SET

WWW.VELLEMANPROJECTS.EU

VM130

USER MANUAL

MODULES

Table of contents

Let’s get started!

Description 3

Receiver instructions 5

Features and specications 4

Transmitter instructions 4

Velleman nv hereby certies that the device VM130 meets

the essential requirements and all other relevant stipulations of

directive ETS 300-220

For the complete conformity declaration

check out :

http://www.velleman.be/downloads/doc/ce_vm130.pdf

VM130USER MANUAL

NO COM NC NO COM NC

CH2

CH1

POWER

COM

OFF

9 - 13

AC/DC

Description

1. ‘Setup’ button

2. 9 to 13Vac or 10 to 15Vdc input

3. Channel 1 output

4. Channel 2 output

5. Heating ON/OFF selection jumper

6. Antenna

7. Channel 1 indication

8. Mode / timer indicator CH1

9. Channel 2 indication

10. Conrm / timer indicator CH2

Disconnect relay outputs during setup!

Any type of power can be used, AC or DC,

the maximum current is 130mA.

The polarity is not important.

7 8 910

Do not mount the unit in the proximity of other electronic devices or metal objects.

Straighten the antenna !

VM130USER MANUAL

Specications

• power supply : 9 to 13 Vac or 10 to 15 Vdc / 130 mA max.

• selectable timers per output: 0.5, 5, 30 s / 1, 5, 15, 30, 60 min

• open eld range of up to 30 m

Receiver:

Transmitter:

• 12 V battery type: V23GA, GP23GA...

• CE compliant 433 MHz operation

• over 1.000.000.000 combinations

Features

• two relay contact outputs (5 A resistive load)

• ON/OFF (toggle) or timer-mode (pulse)

• learning unique 32-bit random code

• up to 31 different transmitters can be stored

• code memory can be erased for safety purposes

• internal heating option for cold environment

Transmitter instructions

The transmitter comes with a factory set default code.

Open the enclosure:

SW1

LED

SW2

SW3

SW1 = CHANNEL 1, SW2= CHANNEL 2

VM130USER MANUAL

Each transmitter generates a code that must be “known” by a receiver in order to operate.

Proceed to the next step to store one or more transmitters in the receiver memory.

To learn a remote:

If neccesary repeat steps 2 to 5 to learn the codes for other transmitters.

u 31 transmitters can be stored. If memory is full, ’MODE’ and ’CONFIRM’ will ash simul-

taneously when ‘setup’ button is pressed (see also next page to erase the memory).

The relay outputs can be set to different modes, from a simple on/of contact to a short or

long timer.

Conguration of channel 1 ‘CH1’ and channel 2 ‘CH2’:

( Factory defaults: CH1: 1h timer, CH2: 0.5s pulse)

If necessary, repeat steps 2 to 5 for the remaining channel.

u The unit returns to normal operation when left idle for 10s.

1. Connect the power supply to the receiver unit (see page 2).

2. Push ‘setup’-button repeatedly to select CH1 (left) or CH2 (right) output relay.

3. Conrm with a long push (‘CONFIRM’ ashes 3 times). The selected relay will re-

main ON.

4. Push ‘setup’-button a number of times, depending on the desired mode (see table).

At each press, ‘MODE’ will ash a number of times, indicating the current mode

5. Conrm with a long push (‘CONFIRM’ ashes 3 times).

The selected channel will turn off and the unit is ready for use.

Changing the code:

1. Hold SW1 (left button).

2. Briey press the ‘program’-button (SW3) 3 times. The LED will ash 3 times.

3. Release SW1.

4. Your unique 32-bit code has been generated and stored.

Return to the default code:

1. Hold SW1 (left button).

2. Hold the ‘program’-button (SW3). After +/- 10s the led will ash 5 times.

3. Release both buttons.

4. Your code has been reset to the default code.

Receiver instructions

1. Connect the power supply to the receiver unit (see page 2)

2. Hold ‘setup’ button, ‘MODE’-led (8) turns on after a few seconds.

3. Press any remote control transmitter button.

4. ‘CONFIRM’-led (10) lights when the code has been grabbed.

5. Release ‘setup’ button.

VM130USER MANUAL

Use:

NOTE: Operate the transmitter during at least 2 seconds.

The left remote button controls CH1 relay, the right remote button controls CH2 relay. Each

relay is equipped with a status LED. In ‘0.5s timer’-mode, a relay will remain on for as long

as the remote button is held.

If a timer has been set for a particular channel, the relay will turn on when the button is

pushed. When the preset time has elapsed, the relay will turn off. A timer can be turned off

at any time by pressing the transmitter button again. As long as the timer is running, the cor-

responding led will ash.

In ‘ON-OFF’-mode, the relay will toggle between ON and OFF every time a button is pushed.

IMPORTANT: To minimise the idle current, remove the heating jumper if the unit is used

inside a car.

To remove all learned remotes from memory:

• turn off the power (disconnect power supply)

• hold ‘setup’ button

• turn on power (connect power supply)

• ‘MODE’ and ’CONFIRM’ start ashing

• release ‘setup’ after the LED’s turn off

uThis process takes about 10 seconds.

u If the button is released before the LED’s turn off, the memory will not be cleared.

u The unit will now respond to the default code only. Please also reset the transmitter to the

default code.

WARRANTY

This product is guaranteed against defects in components and construction from the moment it is

purchased and for a period of TWO YEAR starting from the date of sale.

This guarantee is only valid if the unit is submitted together with the original purchase invoice.

VELLEMAN components Ltd limits its responsibility to the reparation of defects or, as VELLEMAN

components Ltd deems necessary, to the replacement or reparation of defective components. Costs and

risks connected to the transport, removal or placement of the product, or any other costs directly or

indirectly connected to the repair, will not be reimbursed by VELLEMAN components Ltd. VELLEMAN

components Ltd will not be held responsible for any damages caused by the malfunctioning of a unit.

Mode

ON/OFF

0.5 s pulse

5 s timer

30 s timer

1 min timer

5 min timer

15 min timer

30 min timer

1 h timer

Flashes

Velleman nv, Legen Heirweg 33 - Gavere (Belgium)

Vellemanprojects.com

/Velleman-nv @Velleman_RnD ORDERCODE: VM130

REVISION: VM130’3

Otros manuales para VM130

Tabla de contenidos

Otros manuales de Mando a distancia de Velleman

Velleman

Velleman VM152 Manual de usuario

Velleman

Velleman VRC801D2 Manual de usuario

Velleman

Velleman VRC801 Manual de usuario

Velleman

Velleman VRC8 Manual de usuario

Velleman

Velleman High-Q Velleman-kit K8023 Manual de usuario

Velleman

Velleman VM130V2SET Instrucciones de instalación

Velleman

Velleman CAMCOLVC19 Manual de usuario

Velleman

Velleman VRC1001 Manual de usuario

Velleman

Velleman HAMGSM133 Manual de usuario

Velleman

Velleman K6501 Manual de usuario

Velleman

Velleman HQ POWER LEDA03RC Manual de usuario

Velleman

Velleman WRP3B Manual de usuario

Velleman

Velleman VRC801D Manual de usuario

Velleman

Velleman HAA80MK Manual de usuario

Velleman

Velleman VM130 Manual de usuario

Velleman

Velleman CTC1000RC Manual de usuario

Velleman

Velleman MK160 Manual de usuario

Velleman

Velleman VM130V2SET Manual de usuario

Velleman

Velleman VMBIRTS Manual de usuario

Velleman

Velleman HIGH-Q Manual de usuario

Velleman

Velleman CTC1000RC Manual de usuario

Velleman

Velleman vm118 Manual de usuario

Velleman

Velleman WRS3B Manual de usuario

Velleman

Velleman luxibel LX302 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación