Velleman-Kit K8090 Manual de usuario

Total solder points: 363

Difficulty level: beginner 1 2 3 4 5 ⌧advanced

8 CHANNEL USB RELAY CARD

ILLUSTRATED ASSEMBLY MANUAL H8090IP-1

UseyourcomputerUSBporttoconnecttotheoutside

world.

K8090

Features & specifications

Eight relay channels controlled by your computer!

Use your computer USB port to connect to the outside world. Connect up to 16A

to each of the high power relays. Board space for extra VDR noise suppressors is

provided and on board push buttons can be used to test/operate all the relays.

Features

 USB-controlled relay card

 manual operation for toggle, momentary or timer operation (selectable through

software)

 timer settings up to 18 hours (DLL function)

 optional open collector connectivity (push button simulation)

 event-driven and open protocol

 two way PC communication (USB Event return)

 LED indication for power and relay action

Optional VDR (type VDR300) transient suppression for use with inductive loads

minimum system requirements:

 PC running USB compatible Windows version

 USB1.1 and USB2.0 full speed compatible

 internet connection for software download

 optional DIN rail enclosure: B8006 (Note: cut-out the USB connector)*

Specifications

• power supply for relays: 9-10Vac or 12 to 14Vdc (500mA)

• 8 high-power relays: 16A each (resistive load)

• dimensions: 160 x 107 x 30mm / 6.3 x 4.2 x 1.2

Adllforownsoftware

developmentcanbedownloaded

fromourwebsite.Testsoftware

completesthepackage.

*If voltages > 30V are connected, then an enclosure must be used !

Assembly hints

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project

successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a

small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to

the tip, to give it a wet look. This is called ‘thinning’ and will protect the tip,

and enables you to make good connections. When solder rolls off

the tip, it needs cleaning.

• Thin raisin-core solder. Do not use any flux or grease.

• A diagonal cutter to trim excess wires. To avoid injury when cutting

excess leads, hold the lead so they cannot fly towards the eyes.

• Needle nose pliers, for bending leads, or to hold

components in place.

• Small blade and Phillips screwdrivers. A basic range

is fine.

For some projects, a basic multi-meter is required, or might

be handy

1.2 Assembly Hints :

⇒Make sure the skill level matches your experience, to avoid disappointments.

⇒Follow the instructions carefully. Read and understand the entire step before

you perform each operation.

⇒Perform the assembly in the correct order as stated in this manual

⇒Position all parts on the PCB (Printed Circuit Board) as shown on the

drawings.

⇒Values on the circuit diagram are subject to changes.

⇒Values in this assembly guide are correct*

⇒Use the check-boxes to mark your progress.

⇒Please read the included information on safety and customer service

0.000

* Typographical inaccuracies excluded. Always look for possible last minute man-

ual updates, indicated as ‘NOTE’ on a separate leaflet.

1.3 Soldering Hints :

1- Mount the component against the PCB

surface and carefully solder the leads

2- Make sure the solder joints are cone-shaped

and shiny

3- Trim excess leads as close as possible to the

solder joint

REMOVE THEM FROM THE TAPE ONE AT A TIME !

Assembly hints

DO NOT BLINDLY FOLLOW THE ORDER OF

THE COMPONENTS ONTO THE TAPE.

ALWAYS CHECK THEIR VALUE ON THE

PARTS LIST!

Construction

 R1 ... R21 : 1K (1 - 0 - 2 - B)

 R22 : 4.7 (4 - 7 - B - B)

 R23 ... R36 : 100K (1 - 0 - 0 - 3 - 1)

 R37 ... R46 : 200K (2 - 0 - 0 - 3 - 1)

2. Resistors.

R...

 D1 ... D10 : 1N4148

 D11 ... D14 : 1N4007

1. Diodes (check the polarity)

CATHODE

D...

 IC1 : 20p

3. IC socket. Watch the position of

the notch!

 LD1 ... LD11 : 3mm RED

LD1 … LD8 : Output indication

LD9 : USB DATA

LD10 : USB power indication

LD11 : Relay power indication

6. LEDs. Watch the polarity!

LD1

CATHODE

 T1

 T2

 T3

 T4

 T5 BC547B

 T6

 T7

 T8

7. Transistors

 SK10 : B - female

8. USB connector

 C1, C2 : 22pF (22)

 C3 : 10nF (103)

 C4 ... C6 : 100nF (104)

 C7 : 470nF (474)

4. Capacitors

c...

3pins:

 JP1 : event

Set event jumper default to Off.

9. Pinheader

 SW1 ... SW8

(channel 1 to 8)

5. Push button

Construction

 SK1 : 2p power supply



SK2 ... SK9 : 2p (channels 1 ... 8)

10. Terminal blocks

 C8, C9: 4,7µF

11. Electrolytic capacitors.

Watch the polarity !

C...

 X1 : 12MHz

12. Quartz crystal

X...

 VR1 : UA7805

 Check the

orientation !

13. Voltage regulator

VR...

 C10 : 1000µF

14. Electrolytic capacitor.

Watch the polarity !

C...

15. Relays

IC1 : VK8090

programmed

PIC18F14K50-I/P or eq.

16. IC. Watch the position of the

notch!

17. Rubber feet

Mount the rubber feet on

the solder side of the

PCB if you do

not mount the

kit into an DIN

rail enclosure.

18. Open collector input (optional)

Connection diagram for use with an

open-collector system.

1 2 3 54 6 7 8

 RY1  RY5

 RY2  RY6

 RY3  RY7

 RY4  RY8

 Important : Put an extra layer of

solder on all pre-thinned PCB tracks,

to improve their current handling

capabilities.

The card uses a separate supply for the relays and one for the board microcon-

troller.

Test 1:

• Connect a power supply of 9 to 10Vac or 12 to 14Vdc (minimum 500mA).

• The power LED should turn on.

• The USB power LED will also turn on (indicating that the microprocessor power

is ON).

• Push the buttons and the relays should activate.

Test 2:

• Disconnect the power supply.

• Connect the USB port to the PC.

• The USB power LED should turn on.

• Pressing the buttons will make the output indicator LEDs turn on, but the relays

will not activate.

Now the card can be used with all connections.

It is possible to power the card through USB only, but the relays will not activate.

The relay indicator LEDs will work fine.

This mode can be used for software testing.

Check our web site to download more program examples.

19. Test and connection

Test & connection

PCB

Schematic diagram

Ti tl e

Nu mb er R evis ionSize

1N 41 48

LE D3RL

LD1

10 0K

R23

VDR300

VDR1

SK2

1N 41 48

VDR300

VDR2

SK3

1N41 48

VD R3 00

VDR3

SK4

1N 41 48

VDR300

VDR4

SK5

1N41 48

VD R3 00

VD R5

SK6

1N 41 48

VDR300

VDR6

SK7

1N 41 48

VDR300

VDR7

SK8

1N41 48

VD R3 00

VDR8

SK9

SK1

GND

1N 40 07

D1 3

1N 40 07

D1 4

1N 40 07

D11

1N 40 07

D12

GND

10 00 µ /2 5V

C10

LE D3RL

LD11

+12V +12V +12V +12V +12V +12V +12V +12V +12V

GND

10 0n F

BC54 7

GND

OUT1

OU T2

OUT3

OU T6

OUT5

OU T4

OUT7

OU T8

SW1

GND

8 channel USB rel ay card

P8090-2 01

Mode

JP1

LE D3RL

LD1 0

R10

4R7

R22

RB5/ AN1 1/RX /DT

RB6/SCK/SCL

RB7/TX/CK

VU SB 17

RB4/AN10/SDI/SDA

RA3/MCLR/VPP

RC0/AN4/C12IN+/INT0/VREF+ 16

RC1/AN5/C12IN1-/INT1/VREF- 15

RC 2/ AN6 /P 1 D/C 1 2IN2- / CVR EF /INT2 14

RC3/ AN7 /P1C/C12IN3-/PGM 7

RC4/P1B/C12OUT/SRQ 6

RC5/CCP1/P1A/T 0CKI 5

RC6/AN8/SS/T13CK1/T1OSI 8

R C7/ AN 9 /S DO /T1 OS C O 9

RA4/AN3/OSC2/CLKO

RA5/OSC1/CLKI

VDD 1

VSS

D+ / PG D 19

D-/PGC 18

PIC18F14K50-I/P

IC1

VBUS

US B_ D -

US B_ D +

GND

USB CON CC089

SK10

GND

GND GND GND GND

GND

22P

10n

47 0n F

12MHz

4µ7

SW2 SW3 SW8SW7SW6SW5SW4

GND

R13

USB

LD9

200K

R38

200K

R39

20 0K

R40

20 0K

R41

20 0K

R43

20 0K

R44

200K

R45

200K

R46

100K

R31

20 0K

R37

200K

R42

100K

R32

100K

R33

10 0K

R34

10 0K

R35

10 0K

R36

LE D3RL

LD2

100K

R24

BC547

GND

OUT2

LE D3RL

LD3

10 0K

R25

BC547

GND

OUT3

LED3RL

LD4

100K

R26

BC547

GND

OU T4

LE D3RL

LD5

10 0K

R27

BC547

GND

OUT5

LE D3RL

LD6

10 0K

R28

BC54 7

GND

OUT6

LED3RL

LD7

100K

R29

BC547

GND

OU T7

LE D3RL

LD8

10 0K

R30

BC547

GND

OUT8

R11

+5V

R12

100nF

GND GND GND

4.7µ/16-25V

GND

+12V

1N 41 48

D1 0

1N41 48

VPP 1

VDD 2

GND 3

PGD 4

PGC 5

ICSP CONNECTOR

IC S P

GND

CON BTWM10SK11

GND

I O

GND

UA7805

VR1

GND GND

R21

R20

R19

R14

R15

R16

R18

R17

RY1 RY2 RY3 RY4 RY5 RY6 RY7 RY8

Schematic diagram

Otros manuales de Hardware de computadora de Velleman-Kit

Velleman-Kit

Velleman-Kit K5201 Manual de usuario

Velleman-Kit

Velleman-Kit K8016 Manual de usuario

Velleman-Kit

Velleman-Kit K6000 Manual de usuario

Velleman-Kit

Velleman-Kit EDU 05 Guía de instalación y uso

Velleman-Kit

Velleman-Kit K8055 Manual de usuario

Velleman-Kit

Velleman-Kit K8000 Manual de usuario

Velleman-Kit

Velleman-Kit K2655 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario