Vega VEGABAR 55 Manual de usuario

Operating Instructions

VEGABAR 55

4…20 mA

Document ID:

36733

Process pressure/

Hydrostatic

Contents

1About this document

1.1Function.................................. 4

1.2Target group .............................. 4

1.3Symbolism used............................ 4

2For your safety

2.1Authorised personnel ........................ 5

2.2Appropriate use ............................ 5

2.3Warning about misuse ....................... 5

2.4General safety instructions . . . . . . . . . . . . . . . . . . . . 5

2.5Safety label on the instrument . . . . . . . . . . . . . . . . . . 6

2.6CE conformity ............................. 6

2.7Fulﬁllment of NAMUR recommendations . . . . . . . . . . 6

2.8Safety instructions for Ex areas . . . . . . . . . . . . . . . . . 6

2.9Environmental instructions..................... 6

3Product description

3.1Conﬁguration .............................. 7

3.2Principle of operation ........................ 8

3.3Operation................................. 8

3.4Packaging,transport and storage ............... 9

3.5Accessory and replacement parts ............... 9

4Mounting

4.1General instructions ......................... 11

4.2Mounting steps............................. 13

4.3Mounting steps external housing . . . . . . . . . . . . . . . . 14

5Connecting to power supply

5.1Preparing the connection ..................... 15

5.2Connection procedure........................ 16

5.3Wiring plan,single chamber housing . . . . . . . . . . . . . 19

5.4Wiring plan -version IP 66/IP 68,1bar . . . . . . . . . . . 20

5.5Wiring plan,external housing with version IP 68 . . . . . 20

5.6Switch on phase............................ 22

6Set up with the indicating and adjustment module PLICSCOM

6.1Short description ........................... 24

6.2Insert indicating and adjustment module. . . . . . . . . . . 24

6.3Adjustment system .......................... 26

6.4Setup procedure............................ 27

6.5Menu schematic............................ 37

6.6Saving the parameter adjustment data . . . . . . . . . . . . 40

7Maintenance and fault rectiﬁcation

7.1Maintain.................................. 41

7.2Remove interferences........................ 41

2VEGABAR 55 •4…20 mA

Contents

36733-EN-091008

7.3Calculation of total deviation (similar to DIN 16086) . . 43

7.4Exchanging the electronics module . . . . . . . . . . . . . . 44

7.5Software update ............................ 44

7.6Instrument repair ........................... 45

8Dismount

8.1Dismounting steps .......................... 46

8.2Disposal ................................. 46

9Supplement

9.1Technical data ............................. 47

9.2Dimensions ............................... 57

Supplementary documentation

Information:

Supplementary documents appropriate to the ordered version come

with the delivery.You can ﬁnd them listed in chapter "Product

description".

VEGABAR 55 •4…20 mA3

Contents

36733-EN-091008

1About this document

1.1Function

This operating instructions manual provides all the information you

need for mounting,connection and setup as well as important

instructions for maintenance and fault rectiﬁcation.Please read this

information before putting the instrument into operation and keep this

manual accessible in the immediate vicinity of the device.

1.2Target group

This operating instructions manual is directed to trained qualiﬁed

personnel.The contents of this manual should be made available to

these personnel and put into practice by them.

1.3Symbolism used

Information,tip,note

This symbol indicates helpful additional information.

Caution:If this warning is ignored,faults or malfunctions can

result.

Warning:If this warning is ignored,injury to persons and/or serious

damage to the instrument can result.

Danger:If this warning is ignored,serious injury to persons and/or

destruction of the instrument can result.

Ex applications

This symbol indicates special instructions for Ex applications.

lList

The dot set in front indicates a list with no implied sequence.

àAction

This arrow indicates a single action.

1Sequence

Numbers set in front indicate successive steps in a procedure.

4VEGABAR 55 •4…20 mA

1About this document

36733-EN-091008

2For your safety

2.1Authorised personnel

All operations described in this operating instructions manual must be

carried out only by trained specialist personnel authorised by the plant

operator.

During work on and with the device the required personal protective

equipment must always be worn.

2.2Appropriate use

VEGABAR 55 is a pressure transmitter for measurement of gauge

pressure,absolute pressure and vacuum.

You can ﬁnd detailed information on the application range in chapter

"Product description".

Operational reliability is ensured only if the instrument is properly used

according to the speciﬁcations in the operating instructions manual as

well as possible supplementary instructions.

For safety and warranty reasons,any invasive work on the device

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer.Arbitrary

conversions or modiﬁcations are explicitly forbidden.

2.3Warning about misuse

Inappropriate or incorrect use of the instrument can give rise to

application-speciﬁc hazards,e.g.vessel overﬁll or damage to system

components through incorrect mounting or adjustment.

2.4General safety instructions

This is a high-tech instrument requiring the strict observance of

standard regulations and guidelines.The user must take note of the

safety instructions in this operating instructions manual,the country-

speciﬁc installation standards as well as all prevailing safety

regulations and accident prevention rules.

The instrument must only be operated in a technically ﬂawless and

reliable condition.The operator is responsible for trouble-free

operation of the instrument.

During the entire duration of use,the user is obliged to determine the

compliance of the required occupational safety measures with the

current valid rules and regulations and also take note of new

regulations.

VEGABAR 55 •4…20 mA5

2For your safety

36733-EN-091008

2.5Safety label on the instrument

The safety approval markings and safety tips on the device must be

observed.

2.6CE conformity

This device fulﬁlls the legal requirements of the applicable EC

guidelines.By attaching the CE mark,VEGA provides a conﬁrmation

of successful testing.You can ﬁnd the CE conformity declaration in the

download area of www.vega.com.

2.7Fulﬁllment of NAMUR recommendations

With respect to compatibility,the NAMUR recommendation NE 53 is

fulﬁlled.This applies also to the corresponding indicating and

adjustment components.VEGA instruments are generally upward and

downward compatible.

lSensor software to DTM VEGABAR 55

lDTM VEGABAR 55 for adjustment software PACTware

lIndicating and adjustment module for sensor software

The parameter adjustment of the basic sensor functions is independ-

ent of the software version.The range of available functions depends

on the respective software version of the individual components.

2.8Safety instructions for Ex areas

Please note the Ex-speciﬁc safety information for installation and

operation in Ex areas.These safety instructions are part of the

operating instructions manual and come with the Ex-approved

instruments.

2.9Environmental instructions

Protection of the environment is one of our most important duties.That

is why we have introduced an environment management system with

the goal of continuously improving company environmental protection.

The environment management system is certiﬁed according to DIN

EN ISO 14001.

Please help us fulﬁl this obligation by observing the environmental

instructions in this manual:

lChapter "Packaging,transport and storage"

lChapter "Disposal"

6VEGABAR 55 •4…20 mA

2For your safety

36733-EN-091008

3Product description

3.1Conﬁguration

The scope of delivery encompasses:

lVEGABAR 55 pressure transmitter

lDocumentation

-this operating instructions manual

-Test certiﬁcate for pressure transmitters

-Operating instructions manual 27835 "Indicating and adjust-

ment module PLICSCOM"(optional)

-Supplementary instructions manual 31708 "Heating for in-

dicating and adjustment module"(optional)

-Supplementary instructions manual "Plug connector for con-

tinuously measuring sensors"(optional)

-Ex-speciﬁc"Safety instructions"(with Ex-versions)

-if necessary,further certiﬁcates

VEGABAR 55 consists of the components:

lProcess ﬁtting with measuring cell

lHousing with electronics,optionally available with plug connector

lHousing cover,optionally available with indicating and adjustment

module PLICSCOM

The components are available in diﬀerent versions.

Fig.1:Example of a VEGABAR 55 with process ﬁtting G1½Aand plastic

housing

1Housing cover with integrated PLICSCOM (optional)

2Housing with electronics

3Process ﬁtting with measuring cell

The type label contains the most important data for identiﬁcation and

use of the instrument:

lInstrument type

lArticle and serial number device

Scope of delivery

Components

Type label

VEGABAR 55 •4…20 mA7

3Product description

36733-EN-091008

lTechnical data:Measuring range,process pressure,process

temperature,signal output,voltage supply,protection,protection

class

lOrder number

lArticle numbers,documentation

lSIL identiﬁcation (with SIL rating ex works)

The serial number allows you to access the delivery data of the

instrument via www.vega.com,"VEGA Tools"and "serial number

search".In addition to the type label outside,you can also ﬁnd the

serial number on the inside of the instrument.

3.2Principle of operation

VEGABAR 55 is a pressure transmitter for use in the chemical,food

processing and pharmaceutical industries.Depending on the version,

it is used for level,gauge,absolute pressure or vacuum measurement.

Measured products are gases,vapours and liquids,also those with

higher temperatures.

The METEC

measuring cell is the measuring unit.It consists of the

ceramic-capacitive CERTEC

measuring cell and a special,temper-

ature-compensating isolating system.

The hydrostatic pressure of the product or the process pressure

causes a capacitance change in the measuring cell via the metal

process diaphragm and the isolating liquid.This change is converted

into a corresponding output signal.

Two-wire electronics 4…20 mAfor power supply and measured

value transmission over the same cable.

The supply voltage range can diﬀer depending on the instrument

version.The exact range is stated in chapter "Technical data".

The background lighting of the indicating and adjustment module is

for this.You can ﬁnd the exact voltage speciﬁcations in chapter

"Technical data".

The optional heating requires its own operating voltage.You can ﬁnd

details in the supplementary instructions manual "Heating for indicat-

ing and adjustment module".

This function is generally not available for approved instruments.

3.3Operation

VEGABAR 55 can be adjusted with diﬀerent adjustment media:

lwith indicating and adjustment module

lwith the suitable VEGA DTM in conjunction with an adjustment

software according to the FDT/DTM standard,e.g.PACTware and

Application area

Functional principle

Power supply

8VEGABAR 55 •4…20 mA

3Product description

36733-EN-091008

3.4Packaging,transport and storage

Your instrument was protected by packaging during transport.Its

capacity to handle normal loads during transport is assured by a test

according to DIN EN 24180.

The packaging of standard instruments consists of environment-

friendly,recyclable cardboard.For special versions,PE foam or PE foil

is also used.Dispose of the packaging material via specialised

recycling companies.

Transport must be carried out under consideration of the notes on the

transport packaging.Nonobservance of these instructions can cause

damage to the device.

The delivery must be checked for completeness and possible transit

damage immediately at receipt.Ascertained transit damage or

concealed defects must be appropriately dealt with.

Up to the time of installation,the packages must be left closed and

stored according to the orientation and storage markings on the

outside.

Unless otherwise indicated,the packages must be stored only under

the following conditions:

lNot in the open

lDry and dust free

lNot exposed to corrosive media

lProtected against solar radiation

lAvoiding mechanical shock and vibration

lStorage and transport temperature see chapter "Supplement -

Technical data -Ambient conditions"

lRelative humidity 20 …85 %

3.5Accessory and replacement parts

The indicating and adjustment module PLICSCOM is used for

measured value indication,adjustment and diagnosis.It can be

inserted into the sensor and removed at any time.

You ﬁnd further information in the operating instructions "Indicating and

adjustment module PLICSCOM"(Document-ID 27835).

Flanges are available in diﬀerent versions according to the following

standards:DIN 2501,EN 1092-1,ANSI B 16.5,JIS B 2210-1984,

GOST 12821-80.

You will ﬁnd additional information in the supplementary instructions

manual "Flanges according to DIN-EN-ASME-JIS"(Document-ID

31088).

Packaging

Transport

Transport inspection

Storage

Storage and transport

temperature

Indicating and adjust-

ment module

Flanges

VEGABAR 55 •4…20 mA9

3Product description

36733-EN-091008

The protective cover protects the sensor housing against soiling and

intense heat from solar radiation.

You will ﬁnd additional information in the supplementary instructions

manual "Protective cover"(Document-ID 34296).

The electronics module is a replacement part for pressure transmitter

VEGABAR.One version is available for each type of signal output.

You ﬁnd further information in the operating instructions "Electronics

module VEGABAR series 50 and 60 "(Document-ID 30175).

Protective cover

Electronics module

10 VEGABAR 55 •4…20 mA

3Product description

36733-EN-091008

Tabla de contenidos

Otros manuales de Transmisor de Vega

Vega

Vega VEGABAR S 14 Manual de usuario

Vega

Vega VEGABAR 86 Manual de usuario

Vega

Vega VEGABAR 87 Manual de usuario

Vega

Vega VEGABAR 81 Manual de usuario

Vega

Vega VEGADIF 65 Manual de usuario

Vega

Vega VEGABAR 67 Manual de usuario

Vega

Vega VEGABAR 83 Manual de usuario

Vega

Vega VEGABAR 81 Manual de usuario

Vega

Vega VEGABAR 87 Manual de usuario

Vega

Vega VEGADIF 65 Manual de usuario

Vega

Vega VEGADIF 65 Manual de usuario

Vega

Vega VEGABAR 81 Manual de usuario

Vega

Vega VEGABAR 83 Manual de usuario

Vega

Vega VEGABAR 86 Manual de usuario

Vega

Vega VEGABAR 81 Manual de usuario

Vega

Vega VEGABAR 82 Manual de usuario

Vega

Vega VEGABAR 87 Manual de usuario

Vega

Vega VEGABAR 83 Manual de usuario

Vega

Vega VEGAWELL 52 Manual de usuario

Vega

Vega VEGABAR 81 Manual de usuario

Vega

Vega VEGABAR 64 Manual de usuario

Vega

Vega VEGABAR 81 Manual de usuario

Vega

Vega VEGABAR 81 Manual de usuario

Vega

Vega VEGABAR 29 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario