VDO MC 2.0 WR Manual de usuario

ITNLPL FRES ENG DE

MC 2.0 WR

DE Bedienungsanleitung

ENG Instruction Manual

FR Manuel d‘ Installation et d‘ Utilisation

IT Manuale d‘ Installazione e Funzionamento

ES Instalacion y operación manual

NL Handleiding

PL Instrukcja obslugi licznika

MC 2.0

MC 2.0 WR VDO CYCLECOMPUTING

DE ENG FR ESIT NL PL

Introduction

Congratulations

In choosing a VDO computer, you have opted for high-quality device with the latest technology. In order to fully beneﬁt from the potential of the

computer, we recommend that you carefully read this manual. It contains the full operating instructions and many useful tips.

We hope you enjoy cycling with your VDO bike computer.

Cycle Parts GmbH

Pack contents

First, please ensure that the contents of this pack are complete:

 VDO computer  universal handlebar bracket

with cable and sensor

Accessories:

 spoke magnet

(clip magnet)

Cable ties

for attaching the bracket

and the sensor

 rubber pad

for sensor

 battery  V-

for computer

ITNLPL FRES ENG DE

www.vdocyclecomputing.com MC 2.0 WR 

Table of contents

1. Display 36

2. Operation 38

3. Functions 40

3.1 Information functions, BIKE 40

3.2 Information functions, ALTI 41

3.3 Information on P-button 42

3.4 Selecting Bike 1 or Bike 2 43

3.5 Display backlight 44

3.6 Selecting the start altitude /

recalibrating the current altitude 44

3.7 Auto-start/stop of the computer 45

3.8 Start/stop of the stopwatch 45

4. Reset 46

4.1 Resetting the trip data 46

4.2 Resetting the stopwatch 46

4.3 Resetting the NAVIGATOR 47

4.4 Resetting to factory settings 47

5. Installation 48

5.1 Fitting the sensor, magnet and handlebar bracket 48

5.2 Installing the battery in the computer 49

5.3 Inserting the computer into the handlebar bracket 49

6. Basic settings 50

6.1 Selecting the language 50

6.2 Setting the units (kmh/mph, Meter/feet,

Celsius/Fahrenheit) 50

6.3 Setting the tyre size (wheel-circumference) 51

6.4 Setting the clock 53

6.5 Setting the odometer 54

6.6 Setting the navigator 55

6.7 Setting the ride time 56

6.8 Setting the start altitude/home altitude 57

6.9 Setting the current altitude/actual altitude 58

6.10 Automatic altitude adjustment during bike transport 59

6.11 Setting the altitude gain uphill 59

6.12 Setting the altitude loss downhill 60

7. Sleep mode 61

8. Terms of guarantee 62

9. Troubleshooting 63

10. Technical speciﬁcations 64

>>> P02 references at the start of a section refer to the pictures in the

picture book!

MC 2.0 WR VDO CYCLECOMPUTING

DE ENG FR ESIT NL PL

1. Display

The display can be divided

into six areas:

Area 

Temperature,

current altitude

Area 

current uphill/

downhill gradient

Area 

Current speed

Area 

Data for the selected function

Area 

Top line (info line) shows the name

of the selected function. Second

line (menu line) displays,

Bwhether there is more

information “MORE”.

Bwhether there is another

selection option “SELECT”.

Area 

Indicator elements.

The descriptionoftheindividual

indicators can be found on

the right-hand side.

!Your VDO computer comes without battery built in. Before you start, please insert battery.

See also section 5.2.

ITNLPL FRES ENG DE

www.vdocyclecomputing.com MC 2.0 WR 

Stopwatch indicator

Shows that the stopwatch is still running whilst other information is

provided on the display.

Indicator bike /bike 

The computer can use two different settings for two bikes.

The indicator shows which of the two bikes you have chosen to use.

The total distance is measured and stored separately for bike 1 and

bike 2.

Measurement unit (KMH or MPH)

The computer can display both KMH and MPH. Distances are

correspondingly displayed in kilometers or miles. The indicator

shows the selected measurement unit.

Display backlight

The LIGHT ICON indicates if the backlight-mode has been switched on.

Difference indicator – speed (current) to speed (average)

The computer compares the current speed with the average speed.

The indicator shows whether the current speed is

Bgreater than the average speed (+1 km/h)

Bless than the average speed (-1 km/h)

Bor the same as the average speed (tolerance +/- 1 km/h)

Menu prompt indicator

When a submenu has been accessed, these indicators ﬂash and show

that there are other selection options or that the computer is waiting

for an entry (setting mode).

Downhill-Indicator, shows declination

Uphill-Indicator, shows inclination

MC 2.0 WR VDO CYCLECOMPUTING

DE ENG FR ESIT NL PL

C = CLEAR

A = ALTI

M = MENU

P = STOP-

WATCH

BIKE

FUNCTION 

FUNCTION 

FUNCTION 

FUNCTION 

C= CLEAR

In function mode:

BJump back a menu level from the submenu.

BPress and hold Cfor three seconds:

B Reset trip data to zero.

B Reset stopwatch to zero.

B Reset navigator to zero.

In setting mode:

BPress and hold Cfor three seconds:

Exit the settings menu,

return to function mode.

BCorrect an entry.

BJump back a digit.

M= MENU

In function mode:

BAccess available submenu.

You can recognise a submenu by

the ﬂashing menu indicators.

BConﬁrm selection.

BStart/stop the stopwatch.

BPress and hold Mfor three seconds:

B Open the settings menu.

In setting mode:

BSelect a setting.

BConﬁrm a setting.

BConﬁrm a selection made.

A= ALTI

In function mode:

BAltitude information is displayed.

In setting mode:

BScroll backwards in the menu.

BDecrease the number to be set.

P= STOPWATCH

In function mode:

BDisplay of stopwatch and clock

In setting mode:

BScroll forwards in the menu.

BIncrease the number to be set.

= BIKE

In function mode:

BBike functions

Menu indicators on the display ﬂash to show that there are other

selection options. In function mode, the computer is operated using

ﬁve buttons. In setting mode, the computer is operated using four

buttons.

2. Operation

To make your computer easy to use, we have developed the EMC =

Easy Menu Control system. The EMC makes your computer easier to

operate by means of full-text menu guidance, as is used on most

mobile phones.

ITNLPL FRES ENG DE

www.vdocyclecomputing.com MC 2.0 WR 

A= ALTI

In function mode:

BAltitude information is displayed.

BIf the submenu is open:

Scroll down in the submenu.

BPress and hold ALTI for three seconds:

Opens the menu for recalibrating the current altitude.

In setting mode:

BScroll down within the setting modes.

BDecrease a digit.

P= STOPWATCH

In function mode:

BDisplay of stopwatch and clock

In setting mode:

BScroll up within the setting modes.

BIncrease a digit.

= BIKE

BDisplays the bike functions, e.g. trip distance, average speed etc.

A+ P= ALTI+P

BPress the buttons ALTI+P to start/stop the stopwatch.

BThe stopwatch immediately appears on the display and

is started or stopped.

+ C= BIKE+CLEAR

BPress the buttons BIKE+CLEAR to activate the display backlight.

BWhen the display backlight is activated, the LIGHT icon is

displayed.

BWhen the display backlight is activated, the display is lit for a few

seconds every time a button is pressed.

ATTENTION: press the buttons BIKE + CLEAR again to switch off the

display backlight during the day.

This SAVES BATTERY POWER.

MC 2.0 WR VDO CYCLECOMPUTING

DE ENG FR ESIT NL PL

3. Functions

3.1 Information functions, BIKE

CURRENT SPEED

Permanently shown on the display.

Accuracy: 0,2 KMH/MPH

TRIP DISTANCE

Shows the distance of the current trip since the last reset.

Maximum value 999.99 km or miles. If the maximum value is exceeded,

the odometer starts again at zero.

TRIP DISTANCE/MORE

MORE indicates that there is a submenu

for the main menu TRIP DISTANCE.

Open the submenu by pressing M.

In the submenu you will ﬁnd (scroll by pressing ALTI Aor P):

BTotal distance BIKE 1 up to max. 99,999 km or miles

BTotal distance BIKE 2 up to max. 99,999 km or miles

BTotal distance for bike 1 + bike 2 up to max. 199,999 km or miles

Exit the submenu by pressing C.

RIDE TIME

Shows the ride time for the current trip distance since the last reset.

Maximum 99:59:59 HH:MM:SS.

If the maximum value is exceeded, the ride time measurement starts

again at zero.

RIDE TIME/MORE

MORE indicates that there is a submenu for the

main menu RIDE TIME. Open the submenu by

pressing M.

In the submenu you will ﬁnd (scroll by pressing ALTI Aor P):

BTotal ride time bike 1 up to max. 999:59 HHH:MM

BTotal ride time bike 2 up to max. 999:59 HHH:MM

BTotal ride time bike 1 + bike 2 up to max. 1999:59 HHHH:MM

Exit the submenu by pressing C.

AVG SPEED

Shows the average speed since the last reset.

Accuracy: 2 decimal places.

MAX SPEED

Shows the maximum speed on the current trip

since the last reset. Accuracy: 2 decimal places.

ITNLPL FRES ENG DE

www.vdocyclecomputing.com MC 2.0 WR 

NAVIGATOR

The navigator is a second trip distance counter. The NAVIGATOR:

Bis independent of the trip distance counter.

Bcan be reset to zero as often as you want.

Bcan be set to a starting value.

Bcan count forwards or backwards from this starting value.

These special options make it easier to follow instructions from

a touring book or road book.

NAVIGATOR/SET

SET indicates that there is a submenu for the

main menu NAVIGATOR. Open the submenu by

pressing M.

You can set a start value here and decide whether the NAVIGATOR

counts forwards or backwards from this start value.

3.2 Information functions, ALTI

ALTI UP

Shows the altitude gain uphill on the current trip since the last reset.

ALTI UP--MORE--

MORE indicates that there is a submenu for the

main menu ALTI UP. Open the submenu by

pressing M.

In the submenu, you will ﬁnd (scroll by pressing ALTI Aor P):

BAltitude gain uphill for bike 

BAltitude gain uphill for bike 

BTotal altitude gain uphill for bikes  + 

Exit the submenu by pressing C.

ALTI MAX

Shows the maximum altitude (highest point) reached on the

current trip.

ALTI MAX--MORE--

MORE indicates that there is a submenu for the

main menu ALTI MAX. Open the submenu by

pressing M.

In the submenu, you will ﬁnd (scroll by pressing ALTI Aor P):

ALTI MAX for BIKE :

highest point of all previous trips with bike 1.

ALTI MAX for BIKE :

highest point of all previous trips with bike 2.

MC 2.0 WR VDO CYCLECOMPUTING

DE ENG FR ESIT NL PL

AVG CLIMB: average uphill gradient (in percent) on

the current trip.

MAX CLIMB: maximum uphill gradient

(in percent) on the current trip.

ALTI DOWN

Shows the altitude loss downhill on the current trip since the last

reset.

ALTI DOWN--MORE--

MORE indicates that there is a submenu for the

main menu ALTI DOWN. Open the submenu

by pressing M.

In the submenu, you will ﬁnd (scroll by pressing ALTI Aor PULSE P):

BAltitude loss downhill for bike 

BAltitude loss downhill for bike 

BTotal altitude loss downhill for bikes  + 

Exit the submenu by pressing C.

AVG DOWN: shows the average downhill

gradient of the current trip (in percent).

MAX DOWN: shows the maximum downhill

gradient of the current trip (in percent).

CLOCK

shows the current time.

12 hour AM/PM or 24 hour-mode possible

3.3 Information on P-button

STOPWATCH

independent stopwatch for

measuring times/intervals.

Otros manuales para MC 2.0 WR

Tabla de contenidos

Manuales populares de Accesorios para bicicletas de otras marcas

Sigma

Sigma BC 16.16 Manual de usuario

Playcore

Playcore Dero Setbacks Manual de usuario

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manual de usuario

Cateye

Cateye RAPID X2 Manual de usuario

buratti meccanica

buratti meccanica Clorofilla Trail Manual de usuario

Shimano

Shimano SG-8R20 Instrucciones de funcionamiento

BOB

BOB YAK Manual de usuario

APLIC

APLIC 303303/20190717TW012 Manual de usuario

SRAM

SRAM AXS BlipBox Manual de usuario

Garmin

Garmin EDGE 500 Manual de usuario

Shimano

Shimano FD-RX810 Manual de usuario

Cateye

Cateye V2C - Manual de instrucciones

KMART

KMART 43115907 Manual de usuario

SIGMA SPORT

SIGMA SPORT Buster 2000 Manual de usuario

NVO Components

NVO Components STEM Manual de usuario

DAXYS

DAXYS BP188 Manual de usuario

XLC

XLC BV-W17 Manual de usuario

Deda Elementi

Deda Elementi SUPERBOX Manual de usuario