VarTech Systems VT29B-M Manual de usuario

VT29B-M

29” Auto Sync Color Display

User’s Guide

Read these instructions completely before attempting to operate your new Color Display.

VarTech Systems Inc.

Solutions for Demanding Applications

Industrial CRT and Flat Panel Displays

This equipment has been tested and found to comply with the limits for a

ClassAdigital device, pursuant to Part 15 of the FCC Rules. These limits

aredesignedtoprovidereasonableprotection against harmfulinterference

when the equipment is operated in a commercial environment. This

equipmentgenerates, uses, andcan radiateradio frequency energyand if

not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own

expense.

WARNING: To reduce the risk of fire or electric shock, do not expose

this appliance to rain or moisture.

CAUTION: To reduce the risk of electric shock, do not remove cover,

there are no user serviceable parts inside. Refer servicing

to qualified service personnel.

The lightning bolt symbol, within an equilateral triangle,

isintendedtoalerttheusertothepresenceofuninsulated

“dangerousvoltage”withintheproductenclosure thatmay

be of sufficient magnitude to constitute a risk of electric

shock.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions.

CAUTION/ATTENTION *TOPREVENTELECTRICSHOCK,DONOTUSE

THIS(POLARIZED) PLUG WITHANEXTENSION CORD,

RECEPTACLE OR OTHER OUTLET UNLESS THE

BLADES CAN BE COMPLETELY INSERTED TO

PREVENT BLADE EXPOSURE.

FCC Information

CAUTION!

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Table of Contents

WarningandCaution..............................................................................2

ImportantSafetyInstruction....................................................................3-4

ConnectingtheMonitor ..........................................................................5

PDSeriesMonitor Operation..................................................................6-7

ColorMonitorHandHeldRemoteOperation ...........................................8

Power ManagementFunction .................................................................9

TroubleShooting....................................................................................10

CRTSpecifications.................................................................................11

Specifications.................................................................................................12-13

Appendix:TimingCharts..............................................................................14

Warning and Caution

Warning

1. To prevent fire or shock hazard, do not expose this monitor to rain or

moisture.

2. High voltage exists on the cathode-ray tube anode lead of this monitor.

Beforeservicing, determine the presence ofhigh voltagebyconnecting

a H.V. meter between the anode of CRT cap and chassis.

Caution

1. Keepmonitor away from excessive dust, high temperature, moisture or

direct sunlight.

2. Use in a well-ventilated area and do not cover ventilation openings.

3. Unauthorizedmodificationsofthisequipment,substitutionorattachment

of un-shielded connecting cables may cause excessive interference.

4. If the monitor is not in use for an extended time, turn off the power.

Important Safety Instructions

Before operating this equipment, please ensure that you have carefully

followed all the procedures outlined in the user’s manual.

1. Read all instructions

2. Save these instructions for later use

3. Follow all warnings and instructions marked on the product

4. Unplug this product from the wall outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning

5. Do not use this product near water

6. Donotplacethisproductonanunstablecart, standortable.Theproduct

may fall, causing serious damage to the product and personnel

7. Slotsandopeningson the cabinet areprovidedforventilation.Toensure

reliable operation for the product and to protect it from overheating,

these openings must not be blocked or covered. The openings should

never be blocked by placing the product on a bed, sofa, rug, or any

similar surface. This product should never be placed near or over a

radiator or heat register. This product should not be placed in a built-in

installation unless proper ventilation is provided.

8. Thisproductshouldbeoperatedfromthetypeofpowersourceindicated

onthemarkinglabel. Ifyouarenotsureofthetypeofthepoweravailable

consult your dealer or power company.

9. Thisproductisequippedwitha3-wiregroundingtypeplug, a plughaving

athird(grounding)pin. This plug willonlyfit into agroundingtypepower

outlet. This is a safety feature. If you are unable to insert the plug into

the outlet, contact your electrician to replace your obsolete outlet. Do

not defeat the purpose of the grounding -type-plug.

10. Do not allow anything to rest on the power cord. Do not place this

product where persons will trip on the cord.

11. If an extension cord is used with product, make sure the amperage

rating of the extension cord matches the rating of the product. Also,

make sure the total of all products plugged into the wall outlet does

not exceed 15 amperes.

12. Neverpush objects of any kind into this productthrough cabinetslots

as they may touch dangerous voltage points or short out parts that

could result in a risk of fire or electric shock. Never spill liquid of any

kind on the product.

13. Do notattempttoservicethisproductyourself,as openingorremoving

thecover may exposeyou todangerous voltagepointsor otherrisks.

Refer all servicing to a service technician.

14. Unplug this product from the wall outlet and refer servicing to a

qualified service technician under the following conditions:

A. When the power cord or plug is damaged or frayed

B. If liquid has been spilled into the product

C. If the product has been exposed to rain or water

D. If the product does not operate normally when the operating

instructions are followed. Adjust only those controls that are

coveredby theoperating instructionssince improper adjustment

of other controls may result in damage and will often require

extensive work by a qualified technician to restore the product to

normal operation

E. Iftheproducthasbeendroppedor the cabinet has been damaged

F. Iftheproductexhibitsa distinct changeinperformance,indicating

a need for service

Important Safety Instructions

Connecting the Monitor

1. Be sure the monitor and the system unit are switched off.

2. Connect the power cord into theAC INPUT of the monitor.

3. Connect the 15-pin connector of the signal cable to the video control-

ler of the PC, or your signal source.

4. Connectthesignalcableto the monitor.Themonitor supportstwotype

of signal cable: HD-15 or BNC. The monitor will automatically detect

which input is used, however only one type can be connected at

a time.

5. The monitor supports separate sync, composite sync, and sync on

green. When using signal with composite sync, the composite sync

should be connected to the H/H+V connector of the BNC connectors,

or pin 14 of the HD-15 connector.

Terminal Plate Diagram

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Selects OSD function on menu to adjust the

display settings of monitor. The OSD will auto-

maticallydisappear after10 seconds of inactivity.

+ - Increasesanddecreases value ofselected

OSDfunction.

OSDOperation Depressany of four adjustment buttons located

on front of monitor to activate OSD. Once

displayed,choose icon corresponding to

adjustmentrequired. Center of OSDmenu

displaysimage resolution andfrequency.

User’s Controls

Power Switch Push the Power Switch to turn the monitor on and

off. The Power LED near the OSD adjustment

switches will light when the power is on. The LED

will display Green when a valid signal is present,

Amberif themonitor is in power saving mode (sig-

nal is interrupted from computer source). The im-

agewill berestored whenthe signalis receivedby

themonitor.

On Screen Display

 

MONITOROPERATION

POWER

VOL

CH.

REVIEW

MUTE

Color Monitor Hand Held Remote Operation

1234

ON DIP

1234

ON DIP

1234

ON DIP

1234

ON DIP

1234

ON DIP

1234

ON DIP

1234

ON DIP

1234

ON DIP

=3 =4

1234

ON DIP

ON DIP ON DIP

ON DIP

1234

1.Set “Address Setting”on dip switches at rear of monitor:

Set Binary Code on both rows of switches

SW1CONTROLS FIRSTNUMBER, SW 2CONTROLS SECONDNUMBER

1 = 1, 2 = 2, 3 = 4, 4 = 8;ADD VALUES TOACHEIVE DESIRED NUMBER

After setting Binary Code, Monitor Power must be cycled to activate.

2. Depress two digit number on remote to correspond to address setting.

3. Depress “REVIEW”button to activate On Screen Display (OSD).

4. Depress “CH ”or “CH ”button to select adjustment function.

5. Depress “- “or “+ “button to adjust monitor.

6. Depress “POWER”button to save adjustments, and disable remote.

NOTE: The “POWER”button must be depressed when the adjustments are

finished and the OSD is off. This can be confirmed by depressing the “REVIEW”

button again, if the OSD returns, the monitor has not been deselected. Depress

“POWER”button again to deselect monitor.

SW1

SW2

ON = 1

OFF = 0

ON = 1

OFF = 0

Tabla de contenidos

Otros manuales de Monitor de VarTech Systems

VarTech Systems

VarTech Systems VT121XA4 Manual de usuario

VarTech Systems

VarTech Systems DiamondVue VT201C Manual de usuario

VarTech Systems

VarTech Systems VT150CHB Manual de usuario

VarTech Systems

VarTech Systems VT520 Manual de usuario

VarTech Systems

VarTech Systems VT121CC Manual de usuario

VarTech Systems

VarTech Systems VT084XHB Manual de usuario

VarTech Systems

VarTech Systems VTPC2100VS Manual de usuario

VarTech Systems

VarTech Systems VT084XA4 Manual de usuario

VarTech Systems

VarTech Systems VT14B-C1 Manual de usuario

VarTech Systems

VarTech Systems VT190PVS Manual de usuario

VarTech Systems

VarTech Systems VT19B-PW Manual de usuario

VarTech Systems

VarTech Systems vt550 series Manual de usuario

VarTech Systems

VarTech Systems VT170W Manual de usuario

VarTech Systems

VarTech Systems VT420D Manual de usuario

VarTech Systems

VarTech Systems DiamondVue VT190C Manual de usuario

VarTech Systems

VarTech Systems VT420W Manual de usuario

VarTech Systems

VarTech Systems VTPC150XPE Manual de usuario

VarTech Systems

VarTech Systems VT181CH Manual de usuario

VarTech Systems

VarTech Systems ColorVue VT190PC Manual de usuario

VarTech Systems

VarTech Systems VT064C Manual de usuario

VarTech Systems

VarTech Systems GDM-5001PT Manual de usuario

VarTech Systems

VarTech Systems VT420 Series Manual de usuario

VarTech Systems

VarTech Systems VT121 DiamondVue Series Manual de usuario

VarTech Systems

VarTech Systems DiamondVue VT150P Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación