VarTech Systems VT170W Manual de usuario

VT170 Series

17.0” Flat Panel Series LCD Monitors

VT170W · VT170 WX · VT170P ·

VT170PSS · VT170R · VT170RX

User’s Guide

Read these instructions completely before attempting to operate your new Color Display.

VarTech Systems Inc.

Solutions for Demanding Applications

Industrial CRT and Flat Panel Displays

Table Of Contents

Section 1 Section 5

Introduction Touch screen 5.0

About LCD Monitors 1.0 Touch Screen Introduction 5.1

Product Safety Precautions 1.1 Touch Screen Definition 5.2

Section 2 Touch Screen Serial Interface 5.3

Display Setup 2.0 Setting up the Touch Interface 5.4

Display Features 2.1 Installing Windows NT 4.0 Touch Drivers 5.5

Unpacking The Display 2.2 Installing Windows 95/98 Touch Drivers 5.6

Included Parts 2.2.1 Installing Windows 2000 Touch Drivers 5.7

Connecting Your Display 2.3 Section 6

Signal Connections 2.4 Frequently Asked Questions 6.0

Section 3 Section 7

Getting Started 3.0 Troubleshooting Tips 7.0

Adjusting the Display 3.1 Section 8

Adjustment 3.1.1 Cleaning & Maintenance 8.0

Color Adjustment 3.1.2 Section 9

Setup Adjustment 3.1.3 Display Specifications 9.0

Section 4

Mounting Instructions 4.0

Chassis Mount Procedure 4.1

Chassis Mount Drawing 4.1.1

Panel Mount Procedure 4.2

Panel Mount Drawing 4.2.1

Rack Mount Procedure 4.3

Rack Mount Drawing 4.3.1

LCDs

Introduction

Section

About LCD Monitors

What you gain by using an LCD monitor in your industrial controls

are the future of display technology. CRTs although they have dropped

in cost significantly, do not offer the performance, reliability, and

mounting options available with LCDs. LCD monitors consist

primarily of an LCD, Video Board and a Back Light video. The LCD

determines to a large extent the viewing angle, brightness and contrast. Beyond that it is the function of

the video board which converts the analog RGB (Red, Green, Blue) signals from a standard video card

to a high quality, digital RGB that the LCD can display.

Recently the video card has taken on a new role. It is the responsibility of this device to “scale” a

particular video resolution to the “native” resolution of the LCD. Simply, consider that a computer is

putting out a VGA [640x480] resolution signal, yet the LCD that is connected is an XGA [1024x768]

display. The displayed picture would be in the center 1/3 of the LCD. With the introduction of the

scaling engine. The converter will mathematically recalculate the 640x480 to 1024x768. This may sound

simple but it is in fact a complex algorithm that adjusts for different aspect ratios and pixel alignment,

essentially smoothing text and graphics to produce a picture that is pleasant to the eye.

All Vartech displays from 12.1” (800x600) to 23.1 (1600x1200) incorporate scaling engines in the

converter card.

1.0

Product Safety Precautions

⇒ Ensure that sufficient space is available around the display to provide the circula-

tion necessary for cooling.

⇒ Ensure that the ambient air temperature will not exceed the specified maximum

temperature.

⇒ Do not attempt to service this display yourself. The rear chassis has a seal so that

non qualified personal will not expose themselves to dangerous voltages or other

risks.

⇒ To protect from electrical shock, unplug the display power supply from the wall

before moving.

⇒ Do not expose the display to direct sunlight or heat.

⇒ Do not use this display near water

⇒ Do not place any heavy objects on the power cords. Damage may cause electrical

shock.

⇒ Unplug the power supply from the wall or unit if one of the following conditions

exists.

⇒ Power cord or plug is damaged or frayed

⇒ Liquid is spilled into the display or the display is exposed to rain or

water.

⇒ The display does not operate normally when the operating instruc-

tions are followed.

⇒ The display has been dropped or the enclosure has been damaged.

⇒ The display exhibits a distinct change in performance, indicating a

need for service.

1.1

Section

Display Setup

VT170 Series Display Features

⇒ Capable of displaying unlimited colors in a continuous spectrum. The high contrast LCD enhances

the image with no geometric distortion.

⇒ The VT170 Series directly accepts an analog 5 wire RGB with separate H/V sync or 4 wire RGB

with separate combined sync. (3 wire SOG is available as optional)

⇒ The VT170 Series is auto synchronous adjusting the display to the appropriate input between VGA,

SVGA,XGA, and SXGA.

⇒ The VT170 Series is available in Panel Mount, Rack Mount, Wall Mount or Chassis Mount industrial

packages..

⇒ The VT170 Series is supplied with a Anti-Reflective Screen unless equipped with an optional Touch

System.

⇒ The VT170 Series has an integrated 115/220VAC supply as standard on all models except the

chassis model. The chassis model has a +12V jack. The 115/220VAC supply is optional.

⇒ The V7170RX Extreme Series has V-Bonded Glass.

⇒ The V7170RX Extreme Series has Conformal Coating on all circuit boards.

⇒ The V7170RX Extreme Series has ruggedized Amphenol Connectors.

⇒ The V7170RX Extreme Series has a Thermostat controlled heater installed.

2.1

2.2 Unpacking and setting up your display

Your LCD monitor package will consist of the components listed below. Open shipping container

and lay all components on a flat clean surface.

⇒ VT170R or VT170P, or VT170C or VT170W LCD Monitor

⇒ 5 ft Video Cable

⇒ Chassis model only has a +12V power connection. (115/220VAC Power Supply is optional)

⇒ 10-32 Mounting Hardware. (For use with Panel Mount only)

⇒ 6 ft RS232 Touch Interface Cable (Optional when touch is installed)

⇒ CD ROM with Touch Screen Drivers (Optional when touch is installed)

⇒ Users Manual

1. Connect all cables to the computer first. This would include the VGA cable and the optional

RS 232 serial touch screen connection.

2. After connecting the cables between the LCD monitor and the computer, plug the customer

supplied +12VDC source to the 12V connection on the rear (Chassis model only) . All other

models have a integrated 115/220VAC power supply.

3. Once the +12V or the 115/220VAC connection is made, the display is active.

4. If your computer was off, turn on your computer.

5. Your display should now operate as a normal computer display showing your windows or

whatever video is being sent to the flat panel.

Note: If for any reason the display goes blank and gives an “out of Range” or “No Input Signal”,

your computer or video source is putting out a signal that is out of range of the LCD’s video

board. If this happens, reboot the computer or video source and make sure you are inputting the

correct signal. If the display doesn’t work properly, it may be because:

(a) The resolution is to high or low for the LCD.

(b) The refresh rate is set to high. Refresh on an LCD is different than a CRT. Set the refresh to

60Hz. CRT’s need a high refresh rate to avoid flicker. The refresh rate has no impact on

LCD’s.

(d)The unit is malfunctioning. If you believe this to be true, disconnect the video cable from the

rear of the LCD and connect to a known good computer CRT display. If the computer display is

working satisfactory and the video is within the appropriate range, then contact Vartech

Customer service for a RMA number.

2.2.1 What is included with your display

2.3 Connecting the Display

2.4 Signal Connections

To avoid irregular operation and /or damage to the display, please insure correct video is being

supplied as shown on the following page.

2.4 Signal Connections Cont.

Pin assignments for the HD15 video connector.

Pin 1 Red Video Pin 9 No Connection

Pin 2 Green Video Pin 10 Sync Ground

Pin3 BlueVideo Pin11 NotUsed

Pin 4 Not Used Pin 12 Bi-Directional Data

Pin 5 Return Pin 13 Horizontal Sync

Pin 6 Red Video Ground Pin 14 Vertical Sync

Pin 7 Green Video Ground Pin 15 Data Clock (SCL)

Pin 8 Blue Video Ground

Standard Resolutions Supported

⇒ 640 x 480 (VGA)

⇒ 800 x 600 (SVGA)

⇒ 1024 x 768 (XGA)

⇒ 1280 x 1024 (SXGA)

Pin assignment for 9 Pin Optional Touch Screen Connector.

Pin 1 DCD Data Carrier Detect

Pin 2 RD (Rx) Receive Data

Pin 3 SD (Tx) Transmit Data

Pin 4 DTR Data Terminal Ready

Pin 5 SB Signal Ground

Pin 6 DSR Data Set Ready

Pin 7 RTS Request to Send

Pin 8 CTS Clear to Send

Pin 9 NC No Connection

You can use an HD-15 connector cable or a BNC adapter cable to connect the flat panel monitor

to the host computer. The HD-15 video cable (supplied in the kit) you use with this monitor is

equipped with a conventional HD-15 connector at each end.

Note: The following figure is the view looking into the pin end of the male connector or solder

term end of the female connector.

HD-15 Video Connector

The following table provides the pin numbers and corresponding pin

assignments for the HD-15 video connector.

Optional BNC Adaptor Cable

A 5-BNC-to-HD-15 adapter cable is available. The functions of the cables are described below.

⇒ R, B, and G: Red, Green, and Blue input connectors to establish color.

These are used for RS-343 analog signals.

⇒ HS/CS: Separate horizontal/composite sync signal from the video

source.

⇒ VS: Separate vertical sync signal from the video source.

BNC Adapter Cable

This table describes the signal types you can use with the connectors:

BNC Signal Types

BNC Signal Type Description R G B HS/ VS

Sync-on-Green Use the three video connectors.

(optional) Horizontal and vertical syncs are X X X

supplied on the green video line.

Composite Sync Use the three video connectors plus the X X X X

horizontal sync/composite sync input.

Separate Horizontal Use the three video connectors plus the

and Vertical Sync. horizontal sync/composite sync and X X X X X

vertical sync input.

2.4 Signal Connections Cont.

Vartech Displays, Inc

Menu Select Down Up Source

Getting Started 3

Section

3.1 Adjusting the display

The VT170 Series display has an embedded microprocessor in the converter card. Once you

have the unit displaying the resolution you desire for your application do the following:

In order to navigate to the appropriate adjustments, press Menu and the OSD layout chart will

appear as indicated as shown below.

Definition of OSD (on screen display) Adjustments

There are seven membrane buttons (as shown above) located on the rear of the unit. They will

activate the OSD and allow navigation to all adjustments if your unit requires adjustment.

Press MENU and a major adjustment category will appear. Press DOWN or UP and you will

see the remaining adjustment categories. The actual adjustment categories are listed under each

major category (bold) as shown below.

ADJUSTMENT

Brightness, Contrast, Clock, Phase, H Position, V Position, Auto

COLOR ADJUSTMENT

User, 6500, 9300

SETUP

Language, Image Size, OSD H Position, OSD V Position, Transparency, Zoom

PIP (Not available on this model)

On/Off, PIP Source, PIP Size, PIP H Position, PIP V Position, PIP Image

AUDIO (Not available on this model)

Volume, Bass, Treble, Mute, Sound

Adjustment

NOTE: The following adjustments are all under the ADJUSTMENT category. The outlined

procedure covers the sequential adjustments under this category. If you desire to move to an-

other category, press MENU and the UP or DOWN button and proceed to the desired

category.

All adjustments are graphically illustrated in yellow along with a digital value.

Brightness

Press MENU.Press the UP or DOWN button until you reach the ADJUSTMENT