Vanco Evolution EVEX2005 Manual de usuario

HDMI

Transmitter

Connect Power Supply

QUICK INSTALL GUIDE

Factory Setting EDID & EQ Dial - From Factory Settings are as Follows:

1. Transmitter Factory Default Setting is Set at EDID = “0” Supporting: HD (1080p@60) (1080p@30) (1080p@24)

(1080i@60)(720p@60) - 24bit 2D video & 7.1ch audio

2. Receiver E.Q. Dial Setting = “4” Supporting: 20M-25Meters (66 ft to 82 ft)

3. Proceed to Connect & Operate with Normal Installation (see reverse side). If there is no handshake or signal, Adjust EQ

Gain Control according to your CAT5e/CAT6 Cabling: from Minimum Dial Setting “0” to Maximum Setting “7”

Manual EDID Learning Mode

1. Set Learning (Copy) EDID Mode on the Transmitter (TX) unit = “7”

2. (SEE DRAWING) FIRST: Connect Transmitter (TX) unit directly to the Flat Panel Display using a HDMI cable. SECOND:

Connect the 5VDC Power Adapter. The “yellow” Status LED light must blink once for Learning (Copy) EDID to be

Successful. Now you can disconnect Transmitter (TX) from Flat Panel Display.

Note - Do not connect Receiver ( RX) unit during Learning (Copy) EDID Mode

If experiencing No Picture, Picture Flashing, or Drop-Signal then proceed to Manual Learning EDID Mode

NOTE - Recommended EDID setting for most cable and satellite set top boxes is

EDID “4” or “5”. If no signal is displayed after manual EDID learning mode, adjust

to another EDID setting by doing the following:

1. Unplug the 5VDC power supply and HDMI cable from the Transmitter (TX)

2. Adjust EDID to desired setting

3. Reconnect HDMI cable from the source into the Transmitter (TX)

4. Reconnect 5VDC power supply to the Transmitter (TX)

3. Change Transmitter back to Factory Default Setting EDID = “0”

4. Proceed to Connect & Operate with Normal Installation (see reverse side). Wait for Sync

Lights (on Transmitter & Receiver) to Stop Flashing

5. If no Picture or Signal is on the Flat Panel Display then Power OFF (both Units) & Power

ON (both Units). Simply remove the 5VDC Power supplies & reconnect

BluRay® Player

HDTV

HDMI HDMI

IR Transmitter IR Receiver

IR Transmitter

Receiver

HDMI over Cat5e/6

Transmitter Receiver

Back

Front

Back

Front

1. Connect a source such as a Blu-Ray Player, game

console, A/V Receiver, Cable or Satellite Receiver, etc.

to the HDMI input on the Transmitting unit.

2. Connect a display such as an HDTV or HD Projector to

the HDMI output on the Receiving unit.

3. Connect a single Category 5e/6 up to 131ft/40m to

the output of the Transmitting unit, and the other end to

the input of the Receiving unit.

4. For power, plug both the Transmitting unit and Receiving

unit with the included power supplies.

CONNECT AND OPERATE

0 - EDID Full-HD (1080p@60) (1080p@30) (1080p@24)

(1080i@60 (720p@60) - 24bit 2D video & 7.1ch audio

1 - EDID Full-HD(1080p@60) - 24bit 2D video & 2ch audio

2 - EDID Full-HD(1080p@60) - 24bit 3D video & 7.1ch audio

3 - EDID Full-HD(1080p@60) - 24bit 3D video & 2ch audio

4 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video

& 7.1ch audio

5 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video

& 2ch audio

6 - EDID Full-HD(1080p@60) - 36bit 2D video & 7.1ch audio

7 - Auto EDID learning/ Manual EDID learning mode

EQ ROTARY DIAL

If you see ickering or blinking image on the display, adjust the EQ rotary

switch to improve the cable skew. MAX stands for the strongest HDMI

signal level for the longest possible transmission length while MIN stands

for the weakest HDMI signal level for short transmission length. Adjust the

signal level from MIN to MAX until desired video quality is displayed.

Recommended EQ settings

LENGTH

Position Cable Length

0 (MIN)-2 under 15m (49.5ft)

3-5 15-30m (49.5 ft - 99ft)

6-7 (MAX) 30-40m (99ft - 132ft)

EDID SETTINGS

Otros manuales para Evolution EVEX2005

Tabla de contenidos

Otros manuales de Extensor de Vanco

Vanco

Vanco EVOLUTION EV4K2004 Manual de instrucciones

Vanco

Vanco Evolution EV4KWHDMI Manual de usuario

Vanco

Vanco 280723 (164ft) Manual de usuario

Vanco

Vanco Evolution HDBASET EVEX2002 Manual de usuario

Vanco

Vanco EVEX2004 Manual de usuario

Vanco

Vanco EVEXHDARC Manual de usuario

Vanco

Vanco 280591 Manual de usuario

Vanco

Vanco EVEXFBRK1 Manual de usuario

Vanco

Vanco Evolution EV4K2006 Manual de usuario

Vanco

Vanco HDWIRKIT Manual de usuario

Vanco

Vanco Evolution EVEXHDB3 Manual de usuario

Vanco

Vanco Evolution EVEXKVM1 Manual de usuario

Vanco

Vanco EVEXVGAHD Manual de usuario

Vanco

Vanco 280544 Manual de usuario

Vanco

Vanco EVOLUTION EVWP3000 Manual de usuario

Vanco

Vanco Evolution EVEXWHDMI Manual de usuario

Vanco

Vanco Evolution EVEX2005 Manual de usuario

Vanco

Vanco VPW-280577 Manual de usuario

Vanco

Vanco HDEX60 Manual de usuario

Vanco

Vanco Evalution EV4K2006 Manual de usuario

Vanco

Vanco VPW-280572 Manual de usuario

Vanco

Vanco Evolution EVEX4K70 Manual de usuario

Vanco

Vanco 280332 Manual de usuario

Vanco

Vanco EVEX2006 Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario