VADDIO CLEARVIEW HD-18 Manual de usuario
Partner: Vaddio
Model: ClearVIEW HD-18
Device Type: Camera
GENERAL INFORMATION
SIMPLWINDOWS NAME: Vaddio ClearVIEW HD-18 Camera Control v1.0
CATEGORY: Camera
VERSION: v1.0
SUMMARY: This module will control the Vaddio ClearVIEW HD-18 via RS232.
GENERAL NOTES:
This module provides control, real-time feedback from camera, and will also set
various advanced settings. It can have up to 16 presets. Press and hold preset x
input for 2 seconds and the position of camera will save onto that preset number.
There is also a reset mode that when toggled on will erase any preset number when
pressed afterwards.
If multiple units are daisy-chained then it will be necessary to pulse the
Set_Addresses input. This will set the address of each camera.
CRESTRON HARDWARE REQUIRED: C2I-COM, ST-COM, C2-COM-*
SETUP OF CRESTRON HARDWARE:
RS232
Baud:9600
Parity: None
Data Bits: 8
Stop Bits: 1
VENDOR FIRMWARE: Unknown
VENDOR SETUP: DIP switch 4 should be up for the baud rate of 9600.
CABLE DIAGRAM: A DB-9 to RJ-45 adapter is supplied with the camera for RS-232.
CONTROL:
Send_Address_Set D Pulse to set the addresses of the camera.
Power_<On/Off> D Pulse to turn the camera on or off.
Pan_Tilt_* D Press and hold to pan and tilt the camera.
Tilt_Speed A Analog signal to allow the tilt speed to be adjusted. Valid range is 0d to 14d.
Tilt_Speed_<Up/Down> D Pulse to adjust the tilt speed.
Tilt_Speed_Default D Pulse to set the tilt speed to the default value of 7d.
Partner: Vaddio
Model: ClearVIEW HD-18
Device Type: Camera
Pan_Speed A Analog signal to allow the pan speed to be adjusted. Valid range is 0d to 18d.
Pan_Speed_<Up/Down> D Pulse to adjust the pan speed.
Pan_Speed_Default D Pulse to set the pan speed to the default value of 9d.
Zoom_Speed A Analog signal to allow the zoom speed to be adjusted. Valid range is 0d to 7d.
Zoom_<In/Out> D Press and hold to zoom in or out.
Zoom_Speed_<Up/Down> D Pulse to adjust the zoom speed.
Zoom_Speed_Default D Pulse to set the zoom speed to the default value of 4d.
Focus_Speed A Analog signal to allow the focus speed to be adjusted. Valid range is 0d to 7d.
Auto_Focus_<On/Off/Toggle> D Pulse to turn the auto focus on and off.
Focus_<Near/Far> D Press and hold to adjust the focus.
Focus_Speed_<Up/Down> D Pulse to adjust the focus speed.
Focus_Speed_Default D Pulse to set the focus speed to the default value of 4d.
Preset_<1…16> D Pules to recall the preset. Press and hold for 2 seconds to store the current camera
position in the desired preset.
Reset_Mode D Pulse to put the module into preset reset mode. When the Reset_Mode_Is_On
output is high, pulsing a Preset_* input will clear the stored values for that preset.
Auto_White_Balance_<On/Off> D Pulse to turn the auto white balance on and off.
Backlight_<On/Off> D Pulse to turn the backlight on and off.
IR_Recieve_<On/Off/Toggle> D Pulse to turn the IR receiver on and off.
Tally_Light_<On/Off> D Pulse to turn the tally light on and off.
ICR_Cut_Filter_<On/Off> D Pulse to turn the ICR cut filter on and off.
Auto_Exposure_*_Mode D Pulse to set the desired auto exposure mode.
Shutter_<Up/Down> D Pulse to adjust the shutter. Auto Exposure mode must be set to either manual or
shutter priority.
Shutter_Reset D Pulse to set the shutter back to the default setting. Auto Exposure mode must be
set to either manual or shutter priority.
Partner: Vaddio
Model: ClearVIEW HD-18
Device Type: Camera
Aperture_<Up/Down> D Pulse to adjust the aperture.
Aperture_Reset D Pulse to set the aperture back to the default setting.
Gain_<Up/Down> D Pulse to adjust the gain.
Gain_Reset D Pulse to set the gain back to the default setting.
Red_Gain_<Up/Down> D Pulse to adjust the red gain.
Red_Gain_Reset D Pulse to set the red gain back to the default setting.
Blue_Gain_<Up/Down> D Pulse to adjust the blue gain.
Blue_Gain_Reset D Pulse to set the blue gain back to the default setting.
Iris_<Up/Down> D Pulse to adjust the iris.
Iris_Reset D Pulse to set the iris back to the default setting.
Exposure_Compensation_<On/Off> D Pulse to turn exposure compensation on and off.
Exposure_Compensation_<Up/Down> D Pulse to adjust the exposure compensation.
Exposure_Compensation_Reset D Pulse to set the exposure compensation back to the default setting.
IR_Receive_Return_Enable D Pulse to enable. Will send replies what command received from IR commander.
From_Device S Serial data signal to be routed from a 2 way com port.
FEEDBACK:
Power_Is_<On/Off> D High to indicate the current power state.
<Tilt/Pan/Zoom/Focus>_Speed_Gauge A
Analog value indicating the current tilt/pan/zoom/focus speed. To be displayed on a
gauge on a touch panel.
Auto_Focus_Is_<On/Off> D High to indicate the current auto focus state.
Reset_Mode_Is_On D High to indicate that the reset mode is on. Pulsing one of the Preset_<1…16>
while
this is high will reset the values stored for that preset.
Preset_Saved D Will pulse high for two seconds to indicate that the current camera position has
been stored.
Auto_White_Balance_Is_<On/Off> D High to indicate the current auto white balance state.
Partner: Vaddio
Model: ClearVIEW HD-18
Device Type: Camera
Backlight_Is_<On/Off> D High to indicate the current backlight state.
IR_Receive_Is_<On/Off> D High to indicate the current IR receive state.
Tally_Light_Is_<On/Off> D High to indicate the current tally light state.
ICR_Cut_Filter_Is_<On/Off> D High to indicate the current state of the ICR cut filter.
Auto_Exposure_Mode_Is_* D High to indicate the current auto exposure mode.
Exposure_Compensation_Is_<On/Off> D High to indicate the current exposure compensation state.
Error D High to indicate an error was received from the camera.
To_Device S Serial data signal to be routed to a 2 way com port.
TESTING:
OPS USED FOR TESTING: v4.003.0015
SIMPL WINDOWS USED FOR TESTING: 3.01.37
DEVICE DB USED FOR TESTING: 34.00.012.00
CRES DB USED FOR TESTING: 26.00.008.00
SYMBOL LIBRARY USED FOR TESTING: 724
SAMPLE PROGRAM: Vaddio ClearVIEW HD-18 Camera Control v1.0 Demo
REVISION HISTORY: v1.0 – Initial Release
Otros manuales para CLEARVIEW HD-18
2
Otros manuales de Cámara de seguridad de VADDIO
VADDIO
VADDIO PowerVIEW HD-22 Manual de usuario
VADDIO
VADDIO WideSHOT WallVIEW USB Manual de usuario
VADDIO
VADDIO Wallview CCU HD-20 HD-SD Manual de usuario
VADDIO
VADDIO CLEARVIEW HD-18 Manual de usuario
VADDIO
VADDIO WallVIEW CCU HD-19 Manual de usuario
VADDIO
VADDIO ZOOMSHOT 20 Manual de usuario
VADDIO
VADDIO RoboSHOT 12E HDBT Manual de usuario
VADDIO
VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario
VADDIO
VADDIO RoboSHOT Manual de usuario
VADDIO
VADDIO WallVIEW HD-USB PRO System Manual de usuario
VADDIO
VADDIO WALLVIEW PRO H700 Manual de usuario
VADDIO
VADDIO ZOOMSHOT 20 Manual de usuario
VADDIO
VADDIO WIDESHOT WALLVIEW MINI 999-6911-100 Manual de usuario
VADDIO
VADDIO RoboSHOT 12 USB Manual de usuario
VADDIO
VADDIO CeilingVIEW 70 PTZ Manual de usuario
VADDIO
VADDIO CLEARVIEW HD-20SE Manual de usuario
VADDIO
VADDIO CLEARVIEW HD-20SE Manual de usuario
VADDIO
VADDIO RoboSHOT 20 UHD Manual de usuario
VADDIO
VADDIO ZOOMSHOT 20 Manual de usuario
VADDIO
VADDIO RoboSHOT 12 Series Manual de usuario
