Upper Bounce UBES Series Manual de usuario
®
Upper Bounce Inc. 2 Mill St. Cornwall NY 12518, 1-888-965-3331, www.upperbounce.com
Assembly, Installation, Care , Maintenance and Use Instructions.
Enclosure Set &
Enclosure Net
USER MANUAL
Manual Version #05
UPPER
BOUNCE
®
Models begins with UBES: Models begins with UBESOS:
for Outside type Enclosure Sets
Models begins with UBNET:
for Enclosure Nets Only
for Inside type Enclosure Sets
Models begins with UBESFG:
for OS net, FG net for Flex On
Top Models
This Instructions manual is for Upper Bounce Enclosure Sets and
Enclosure Nets which is designed to fit most model Trampolines.
020-3150-0484
Simply follow the assembly and safety instructions in this manual and you will soon be starting your
®
UPPER BOUNCE exercise program and be on your way to a happier, healthier lifestyle.
MONDAY - THURSDAY
9:30 A.M. - 5:00 P.M.
Eastern Time.
FRIDAY
9:00 A.M. - 12:00 P.M.
Eastern Time.
®
THANK YOU FOR PURCHASING THE UPPER BOUNCE TRAMPOLINE PART
Email us
www.upperbounce.com
Call us
Check out our website
support@upperbounce .com
1-888-965-3331
USA UK
support@upperbounce.co .uk
TABLE OF CONTENTS
Page
Measuring Tips For Enclosure Set 3
Measuring Tips For Enclosure Net 4
Enclosure Set Parts List 5
Pole Assembly 6-7
Inside type Enclosure Net Assembly 8
Outside type Enclosure Net Assembly 9-10
Arch type Net Enclosure Net Assembly 11
Ring on top Enclosure Net Assembly 12-13
Replacement Parts List 14-15
UPPER
BOUNCE
®
Before you are ready to start installing your new Enclosure Set, please verify that the enclosure set
you are going to install matches the trampoline size you have.
Thank you for choosing Upper Bounce for your trampoline and trampoline replacement needs!
When you select Upper Bounce®, you are choosing high quality trampolines, or replacement parts
and accessories.At Upper Bounce® we think about "fun and safety" for the whole family!
3
These are the steps to make sure you purchased the right Enclosure Set:
Measuring Tips For Enclosure Set
1
2
3 4
5
6
78
1
2
3
4
1
2
3
4
1
2
3
4
Fig. 1
Count the legs. The amount of W shaped
legs you have that's the amount of poles
you will need.
or connect 2 poles to each leg as shown in
figure 2.
Fig. 2
FRAME SIZE
STEP 1
POLE AMOUNT
STEP 2
STEP- 1
STEP- 2
1FT
1FT 2FT 3FT 4FT 5FT 6FT 7FT 8FT 9FT 10FT 11FT 12FT 13FT
14
FT
14 FT
14FT
Measure your frame from one
outside
edge vertically and
horizontally to the other outside
edge so you get the correct
measurements.
Measure the diameter of your trampoline leg to make sure that the pole connecting tool
fits your trampoline. If the leg measures up to 1.75" you will need a 1.75" connector.
57.1
STEP 3POLE CONNECTOR
Determine if you bought the correct Enclosure Set
1) Frame Size 2) Leg Amount 3) Leg Diameter
Based on the
If you purchased an enclosure net only
1. Make Sure the Net size matches the frame size (see above how to measure the frame size).
2. Make sure the poles/arch amount of the product matches the amount of your trampoline.
3. Make sure the height of the product is matching to the height of your existing poles or arches.
7.5 ft
8 ft
9 ft
10 ft
12 ft and +
65"
65"
65"
64"
71"
Height chart of all type of nets
Measuring Tips For Enclosure Net
4
STEP- 3
5
ENCLOSURE SET PARTS LIST
ITEM
PART IMAGE
E-1
UBES104
UBES124
UBES144
UBESOS124
UBES86
UBES126
UBES146
UBES156
UBES106
UBES136
UBES166
UBESOS7.56
UBESOS126
UBESOS136
UBESOS146
UBESOS156
UBES128
UBES148
UBES158
UBES138
UBESOS138
UBESOS148
UBESOS158
UBESFG158
UBESFG178
4
4 0
0 0
0
0
0
0 0
00
0
4
6
6
6 8
8
A
A-1
Upper Pole
B
4 6 8
Lower Pole
C
812 16
Clamp
Tool Set
D
1 1 1
Tool
Pole Cap
F
1 1 1
Enclosure
Net
NAME
QUANTITY
MODELS
For Inside
Type
For Outside
Type
For FG Type
E-2
E-3
G
Big Rope 1 1 1
T
4 6 8
PVC Sleeve
(Do not use
these sleeves
if you have
an outside net)
8
4
40 0 0
000
6
6 8
8
For FG Type
For ES/OS Type
UBESFG86
UBESFG116
UBESFG126
UBESFG136
UBESFG146
UBESFG156
UBESFG144
UBESFG124
UBESFG155
5
5
16
1
1
1
5
0
5
6
18 inches
1. First, place all parts to be used in the process of
installation in front of you.
For straight poles - For the lower poles use the
ones that are tapered.
For curved poles - Use the curved pole as the
upper pole.
2. Take the clamp and clasp the lower enclosure
pole into the rounded end of the clamp. Make
sure that the black rubber cap of the lower pole
faces down.
a) If the pole fits too loosely, insert the green
rounded piece before clasping the pole so clamp
will tightly clasp the pole.
b) If the pole is too thick and does not fit into the
hole, remove the green rounded piece to create
more space for the pole. You should then be able
to clasp the trampoline pole into the clamp.
c) Once the pole is securely inserted into the
clamp, you should now insert the plastic bracket
until you reach the pole.
3. Be aware that the mark on the lower pole needs
to align with the trampoline frame. If there is no
line on the pole then please have it attached 18”
below the frame.
2 adults in good physical condition are required for the following assembly.
Wear proper shoes and maintain balance to prevent a fall. Failure to follow all
instructions and warnings may result in serious injury.
Warning :
Pole Installation Instructions
Curved Poles UBHWD-CPS4 UBHWD-CPS6 UBHWD-CPS8
(a) (b)
(c)
Straight Poles UBHWD-PS4 UBHWD-PS6 UBHWD-PS8
This Page also to be used for these Models
7
4. The set comes with 2 clamps per pole.
One being attached 2” below frame,
while the other being attached 2” above
the end of the lower pole.
5. Insert the plastic bracket, then clasp the
trampoline leg into the clamp. Secure
tightly with steel brackets and nuts.
6. Now you can have the upper part of the
pole inserted into the lower part that is
already attached to the leg.
7. Repeat the steps above to have all your
enclosure poles connected securely to
your trampoline legs.
Cover all the poles with the PVC Sleeve
(Item T).
8. After connecting all enclosure poles insert the pole caps, if you have an inside type net use
part number E1 and for outside type Net use E2. If you are using the curved poles, use the pole
caps provided.
For inside type net E-1 For outside type net E-2
After you installed the poles you should install the enclosure net. For instructions how to install the
enclosure net see next page for the inside type model and the outside type. Choose the one applies to
your purchase.
2 inches
2 inches
For curved poles
E1 E1
E1
E1 E1
E1
E1
E1 E2
E2
E2
E2
E2
E2
E2
E2
Step Step
Hold the clip piece with the ridges on the
outer bar facing you.
Holding the fabric tie with your other hand,
silde it through the left slot on the clip.
12
Step Step
Turn the tie back and thread the end back
through the clip through the right slot this
time.
,
Adjust to the appropriate length and pull
the tie horizontally until it is taut and
tightens in place.
Front
Back
34
68
INSIDE TYPE MODELS
UBES86
UBES104
UBES124
UBES144
UBES126
UBES128
UBES146
UBES148
UBES156
UBES158
UBES106
UBES136
UBES138
UBES166
UBNET-12-6-IS
UBNET-13-6-IS
UBNET-13-8-IS
UBNET-14-4-IS
UBNET-14-6-IS
UBNET-14-8-IS
UBNET-15-6-IS
UBNET-15-8-IS
UBNET-16-6-IS
Enclosure Nets Enclosure Sets
UBNET-7.5-6-IS
UBNET-8-6-IS
UBNET-8-4-IS
UBNET-9-6-IS-Y
UBNET-10-4-IS
UBNET-10-6-IS
UBNET-10-8-IS
UBNET-12-8-IS
UBNET-12-4-IS
UBNETO-1614
Oval Net UBNETO-1715
Net Installation Instructions
Steps to install the clips
9
STEP 1
STEP 2SECURING THE BOTTOM OF THE NET
NOTE: If you purchased a ring on top enclosure set continue to page 12.
If you purchased a straight
pole Enclosure Set use this step
Note:When installing the net make sure that the Upper Bounce logo is placed on the outside of the trampoline.
STEP- 1
STEP- 2
1. Connect the net to the V-rings of the
trampoline mat using the attached clips, securing
at regular intervals. This holds the net in place for
you to complete the attachment with rope.
2. Secure one end of the rope by knotting it to
the V-ring closest on one side to the trampoline
entrance zipper.
3. Weave the rope through the net and every
second v-ring successively, moving around the
trampoline in the direction away from the
entrance zipper.
4. When you complete the weaving and reach
the other side of the entrance zipper, secure the
other end of the rope also by knotting it to the
V-ring closest to the entrance on that side.
Your trampoline safety net is now fully secured.
Follow the safety checks in the ‘Testing the
Trampoline’ section before using the trampoline net.
SECURING THE TOP OF THE NET
OUTSIDE TYPE MODELS
Net Installation Instructions
STEP 1
UBESOS138
UBESOS146
UBESOS148
UBESOS156
UBESOS158
Enclosure Sets Enclosure Nets
UBESOS7.56
UBESOS108
UBESOS124
UBESOS126
UBESOS136
Start installing the Net to the poles by
inserting thebegining of the Sleeve
on the Poles Until it reaches 2 ft.
and continue doing the same to
all poles as figure 1.
Pull down each sleeve, a few inches
at a time till all sleeves reac the bottom
of enclosure frame asshown in figure 2.
Fig. 1
Fig. 2
UBNET-7.5-6-OS
UBNET-10-8-OS
UBNET-12-4-OS
UBNET-12-6-OS
UBNET-13-6-OS
UBNET-13-8-OS
UBNET-14-6-OS
UBNET-14-8-OS
UBNET-15-6-OS
UBNET-15-8-OS
10
STEP- 1SECURING THE TOP OF THE NET
Este manual sirve para los siguientes modelos
43
Tabla de contenidos
