Universal Remote Control URC-SR3 Manual de usuario

URC-SR3

Remote Control

Owner’s Manual

Congratulations!

Congratulations on purchasing Universal Remote

Control’s URC-SR3 Pre--Programmed and Learning

remote control. You now have the power to control

your entire home entertainment system with one

easy--to--use remote. The URC-SR3 can be used with

thousands of TV/DVD components because of

the extensive library of codes that have already

been programmed into the remote. So... get ready

to sit back, relax, and simplify your home

entertainment experience.

This Owner’s Manual is designed to assist you in

programming your URC-SR3 remote to work with

your components by guiding you through an easy

step-by-step process. Everything you need to know

about programming the URC-SR3 is contained in

this Manual.

Remote Control, Inc.

This document is protected by the copyright laws of

the United States and internationally by the Berne

Convention. No part of this manual may be

reproduced in any form without the express written

consent of Universal Remote Control, Inc. Although

reasonable care has been taken to assure the

accuracy of the information herein contained,

Universal Remote Control, Inc. is not responsible for

operational, technical or editorial errors or

omissions.

The specifications and information in this manual

may be subject to change without notice.

MacroPower and SimpleSound are trademarks of

Universal Remote Control, Inc. Entertainment Made

Simple is a registered trademark of Universal

Remote Control, Inc. All other brand or product

names are trademarks or registered trademarks of

their respective owners.

500 Mamaroneck Avenue, Harrison, NY 10528

Phone: (914) 835-4484 Fax: (914) 835-4532

Table of Contents

Getting Started - Overview

• Control up to 3 Components........................4

• Component Buttons.....................................4

• Battery Installation ......................................4

• Low Battery Warning ..................................5

• Couch Mode .............................................5

Keypad Layout & Button Functions .........6

Programming URC-SR3 Using

Pre-Programmed Codes ..........................7

• Quick Set-Up Method .................................7

• Three-Digit Code Entry Method ....................8

• Auto-Search Method .................................10

Programming URC-SR3 Using the

Learning Method.....................................12

Special Advanced Features....................14

• Programming Automated Activities .............14

• MacroPower Total System On/Off ..............14

• “My Button” Custom Programmable

Button .....................................................16

• “My Favorites” – Favorite Channels ............17

• More Favorite Channels ............................18

• Simple Sound™ Total System

Volume Control ........................................19

• Channel Control “Punch Through” ..............21

• Transport Control “Punch Through”.............22

• OSD (On-Screen Display) Control

“Punch Through” ......................................23

Erasing Commands-Overview ..............24

• Erasing a Single Learned Command ...........24

• Erasing All Learned Commands from

One Component ......................................25

• Erasing Macro Power & Other Macro

Commands .............................................26

• Erasing Simple Sound & Other

“Punch Through” Commands .....................27

• Factory Reset ...........................................28

Finding a Component’s Set-Up Code

Number ...................................................29

Pre-Programmed Code Tables ...............30

• CABLE/SAT .............................................31

• TV .....................................................32-33

• DVD/DVR/VCR ...................................34-35

Frequently Asked Questions..................36

Limited Warranty....................................36

Specifications ..........................................37

Information To The User .........................38

Warning...................................................38

Page 4

Getting Started - Overview

Control up to 3 Components

The URC-SR3 remote control is designed to control

up to three different TV/DVD components and

operate virtually all brands of TV, DVD/DVR/VCR,

and CABLE/SAT components.

Component Buttons

Once you have programmed the URC-SR3 for all of

your components, all you need to do is press a

component button and all the buttons on the URC-

SR3 will work with that component. For example,

when you press the TV component button, all the

buttons on your URC-SR3 will operate your TV. If you

press the DVD/DVR component button, all the

buttons on the URC-SR3 will operate your DVD/DVR.

Each time you press any of the buttons on the

remote, the LED light in the component button will

light up to indicate which component you are

controlling.

Battery Installation

Press the tab and remove the cover of the battery

compartment located in the back of your remote.

Insert the two AAA batteries (included in the

package) making sure to match the positive (+) and

negative (-) symbols as shown in the diagram.

Place the cover back over the battery compartment.

INSERT BATTERIES

CORRECTLY

TV BUTTON

Page 5

Low Battery Warning

When the batteries are low and need to be

replaced the component LED will quickly blink two

times when you press the [Power] button.

Couch Mode

The URC-SR3 is designed to automatically turn itself

off if a button is pressed for more than 30 seconds.

This prevents battery power from being depleted

should the remote accidentally slip between the

couch cushions.

PLEASE DO NOT RETURN

THIS PRODUCT TO THE STORE

PLEASE CONTACT OUR TECHNICAL

SUPPORT CENTER

IF YOU NEED ASSISTANCE, E-MAIL

techsuppor[email protected]

or dial 1-800-901-0800

(9:00AM-6:00PM EST)

Page 6

Keypad Layout & Button

Functions

Allows you to turn the

selected component

on and off.

POWER

Designed to send Power

On/Off commands for up to

three components with one

button press.

ALL OFF

Used to select the

component you want

to operate and signals

remote control activity.

Displays the

Applications Menu

through the Cable

Set Top Box.

CBL/SAT, TV, DVD

Exits from current

screen through the

Cable Set Top Box.

Use to enter code

numbers for

programming

components and to

enter channel

numbers to tune in

channels. Also used to

make numeric entries

on on-screen menus.

Perform standard

DVD and DVR

functions when in

DVD and DVR

mode, or VOD

(Video-On-

Demand) and

DVR (Digital

Video Recorder)

functions when in

Cable mode.

Custom-

programmable

Button

Displays the

Program Guide

listings through

the Cable Set

Top Box.

Displays

information about

the program

currently playing

or highlighted in

the Program

Guide through the

Cable Set Top Box.

INFO

GUIDE

Used for

programming

steps and on-

screen navigation

and highlighting.

CURSOR

NAVIGATION

PAD

EXIT

Selects highlighted

screen options.

SELECT

Selects the video

source from

available

components.

INPUT

Returns to the

previously tuned

channel through

the Cable Set

Top Box.

LAST

Silences the Sound.

Press to activate.

Press again to

restore sound to

the previous level.

MUTE

NUMBER

PAD

TRANSPORT

CONTROLS

MY BUTTON

VOLUME

Raises or

lowers the

sound volume.

Custom-

programmable

Favorite Channel

Buttons

FAVORITES

Page 7

Programming URC-SR3 using

Pre-Programmed Codes

There are three different ways you can program

your URC-SR3 using the component brand codes

that are pre-programmed into the remote. One of

these will work for you!

• Quick Set-Up Method

• Three-Digit Code Entry Method

• Auto-Search Method

* * *

TRY THIS FIRST!

Quick Set-Up Method

STEP 1: Manually or using your old remote, turn

on the component you want to program—for

example, to program your TV, turn on your TV set.

STEP 2: Point the URC-SR3 toward the component

that you want to program (in this case the TV set)

and press and hold the component button (in this

case the TV button). While holding down the

component button, begin to press numeric

keys, one number at a time, starting from 1,

continuing to 2, 3 ... 0 until component (in this case

the TV) turns off.

STEP 3: Release the component button to save the

code. The component LED light will blink two times

to confirm that the code has been stored.

Repeat the above three steps for other components.

COMPONENT

BUTTONS

NUMBER

PAD

Page 8

IFQUICK SET-UP DID NOT WORK, TRY THIS

Three-Digit Code Set-Up Method

STEP 1: Find the 3-digit code numbers assigned to

your brand from the lists in the back of this manual.

The codes are listed by component category (i.e.,

CBL/SAT, TV, DVD/DVR, etc.), then by brand

name. For instance, if you would like to locate a

code for a Sony television, first locate the TV

category and then look for the Sony brand.

STEP 2: Once you have located the 3-digit codes

for each of the components that you wish to

operate with your URC-SR3, write them ALL down

on a piece of paper. It’s important that you write

down all the codes listed for your brand because

only one code is going to work with your

component.

STEP 3: Manually or using your old remote, turn

on the component you want to program—for

example, to program your TV turn on your TV set.

STEP 4: On the URC-SR3, press the Component

button that you want to program (in this case the

button that says TV) and the SELECT [SEL] button at

the same time. Hold down both buttons for 2

seconds until the TV Component LED light turns on.

This signals that you are in programming mode.

IMPORTANT: You have 30 seconds to perform

the next step while you are in programming mode.

If you do not press a button within 30 seconds,the

component LED light will turn off. The remote will

exit the programming mode and you will have to

start over.

COMPONENT

BUTTONS

SELECT

BUTTON

Page 9

STEP 5: Point the URC-SR3 toward the component

(in this example the TV) and punch in the first 3-digit

code that you wrote down for that specific

component. Use the Number buttons 0–9 on the

remote to punch in the code. The TV LED light will

blink each time a number is pressed.

If the 3-digit code number you just punched in is

the correct number, the component you are trying to

program will turn off. If it did not turn off, enter the

next code number from your list until it does turn off.

STEP 6: Once you’ve entered the code number

and the component has turned off, press the

POWER button on the URC-SR3 remote to turn the

component back on.

Next test the VOLUME and CHANNEL buttons (or

PLAY and STOP buttons for DVD/DVR) to make sure

they all work. For example, perhaps your Sony TV

turned off with code number 147, but the volume

controls did not work properly. In this case, try the

next code number listed for that component. Repeat

Step 5 using the next code number until you find a

perfect match.

STEP 7: Once you’ve entered a correct code you

must save it. Press the component button you just

programmed (in this case TV) one more time to save

the code number. The component LED light will blink

two times to confirm that the code was successfully

stored. Now when you press the TV component

button, all of the buttons will work with your TV.

Program the remaining components by repeating

steps 3 through 7.

IMPORTANT: If you have tried all the set-up codes

in the list and the component still did not turn off after

Step 5, either the Auto-Search Method (page 10) or

the Learning Method (page 12) will help you

program.

NUMBER

PAD

Page 10

If the Three Digit Code did not

work, try this next:

Auto-Search Method

The Auto-Search Method is a way you can scan

through all of the codes in the table to find the right

code for your component.

STEP 1: Manually or using your old remote, turn

on the component you want to program—for

example, to program your TV, turn on your TV set.

STEP 2: On the URC-SR3, press the Component

button that you want to program (in this case the

button that says TV) and the SELECT [SEL] button at

the same time. Hold down both buttons for 2

seconds until the TV Component button light turns

on. This signals that you are in programming

mode.

IMPORTANT: You have 30 seconds to perform

the next step while you are in programming mode.

If you do not press a button within 30 seconds, the

component LED light will turn off. The remote will

exit the programming mode and you will have to

start over.

STEP 3: Point the URC-SR3 remote control toward

the component and press the UP



arrow (or

DOWN



arrow) button once. Each time the



or DOWN



arrow button is pressed, the

code will count up (or down) one code number

and send a Power OFF signal. When the correct

code is sent out, the component will turn off.

DOWN



ARROW



ARROW

Otros manuales para URC-SR3

Tabla de contenidos

Otros manuales de Mando a distancia de Universal Remote Control

Universal Remote Control

Universal Remote Control Easy Clicker UR2-211 Manual de usuario

Universal Remote Control

Universal Remote Control UR3-EXP Manual de usuario

Universal Remote Control

Universal Remote Control osiris Manual de usuario

Universal Remote Control

Universal Remote Control Easy Clicker UR2-211 Manual de usuario

Universal Remote Control

Universal Remote Control AVEX Manual de usuario

Universal Remote Control

Universal Remote Control MX-980 Manual de usuario

Universal Remote Control

Universal Remote Control Easy Clicker UR3L-SR4 Manual de usuario

Universal Remote Control

Universal Remote Control UR4U-MDVR-CHD2 - SPECS SHEET Manual de usuario

Universal Remote Control

Universal Remote Control ONE FOR ALL 8800CMN Manual de usuario

Universal Remote Control

Universal Remote Control PHAZR-5 series Manual de usuario

Universal Remote Control

Universal Remote Control Easy Clicker UR3-SR3 Manual de usuario

Universal Remote Control

Universal Remote Control UR4-DCT Manual de usuario

Universal Remote Control

Universal Remote Control Easy Clicker UR3L-SR4 Manual de usuario

Universal Remote Control

Universal Remote Control CLIKR-5 UR5U-8500 Manual de usuario

Universal Remote Control

Universal Remote Control UR-J22TVE Manual de usuario

Universal Remote Control

Universal Remote Control PHAZR-5 Manual de usuario

Universal Remote Control

Universal Remote Control MASTERCONTROL RF20 Manual de usuario

Universal Remote Control

Universal Remote Control R2-Mini Manual de usuario

Universal Remote Control

Universal Remote Control UR2-DTA Manual de usuario

Universal Remote Control

Universal Remote Control CLIKR-5 UR5U-8780L Manual de usuario

Universal Remote Control

Universal Remote Control TOTAL CONTROL FX-1 Manual de usuario

Universal Remote Control

Universal Remote Control Clikr-5 UR5U-8820L Manual de usuario

Universal Remote Control

Universal Remote Control MX-500TM Manual de usuario

Universal Remote Control

Universal Remote Control TRC-820 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación