Universal Remote Control Easy Clicker UR3-SR3 Manual de usuario

Universal Remote Control, Inc.

www.universalremote.com

UR3-SR3

Operating Manual

For Easy Clicker

This remote control is designed to operate

most Digital and Analog Cable Boxes, as well

as TVs, and a DVD player.

Introduction

Install two

AAA alkaline batteries

as shown here

Before you program or operate the remote

control, you must install two new AAA alkaline

batteries.

STEP1 Remove the battery compartment cover

from the back of your remote control.

STEP2 Check battery polarity carefully, and

install the batteries as shown in the

illustration below.

STEP3 Replace the battery compartment cover.

Replacing Batteries

A. Quick Set-Up Method

STEP1

Turn on the component you want to

program. To program your TV, turn on the TV.

Button Functions

Programming the Remote Control.

*Note : In this section, when you are instructed to

press a [DEVICE] button, that means you

should press either the CBL, TV, or DVD

button, depending on which device you are

programming the remote to operate.

STEP2

Press and hold the [DEVICE] key for 5

seconds until the Device LED will blink

once and stays on. Continue to hold the

[DEVICE] key and press the number key

assigned to your brand in the Quick Set-

up Code Table and release both [DEVICE]

key and the number key to save the

code. The Device LED will blink twice to

confirm that the code is stored.

STEP3

Point the remote control at the

component.

STEP4

Press the [DEVICE] button. If it turns off,

it is programmed for your component. If it

does not turn off, use the Pre-

Programmed 3-Digit code Method or

Scanning Method.

Repeat the steps above for all components (CBL,

TV, DVD).

B. Quick Set-up Code Tables

Quick Number Manufacturer/Brand

CBL

0 PACE DTA

1 SA/CISCO, SAMSUNG, PACE DIGITAL

2 MOTOROLA DIGITAL

3 MOTOROLA DTA

4 EVOLUTION DTA

5 CISCO IPTV

6 ADB IPTV

7 TECHNICOLOR

8 AMINO 140/540 IPTV

9 MOTOROLA IPTV

C. Manual Programming

The remote control can be programmed by entering

a three-digit code number that corresponds to

particular brands and models of equipment. The

three-digit code numbers are listed in the code

tables sections of this instruction manual.

STEP1 Turn on the equipment that you want the

remote control to operate Cable Box, TV

and DVD.

STEP2 Press the [DEVICE] button and the

DVD

0 HITACHI

1 SONY

2 PHILIPS

3 SAMSUNG

4 PHILIPS MAGNAVOX

5 PANASONIC

6LG

7JVC

8 DENON

9 PIONEER

Quick Number Manufacturer/Brand

0 SANYO

1 SONY

2 SAMSUNG

3LG

4 TOSHIBA

5 PANASONIC

6 PHILIPS

7 HITACHI

8SHARP

9 VIZIO

[OK/SEL] button simultaneously for three

seconds. The corresponding device LED

will turn on indicating that it is ready to be

programmed. The LED will remain on for

20 seconds. The next step must be

entered while the LED is on.

STEP3 Point the remote control toward the

equipment and enter the three-digit code

number assigned to your brand from the

code tables. If there are more than one

three-digit number listed for your brand,

try one code number at a time until your

equipment turns off.

*Note : You can verify that you have selected the

correct code by pressing the [MUTE]

button. The equipment should turn on or

off.

STEP4 Store the three-digit code by pressing the

same [DEVICE] button once again. The

device LED will blink twice to confirm that

the code has been stored.

*Note : Try all the functions on the remote

control. If any of the functions do not

operate as they should, repeat the

instructions from Step 2 using the next

three-digit code number from the same

brand list.

D. Auto Search Method

If none of the three digit code numbers assigned to

your brand of equipment works, or the code table

does not list your brand, you can use the Auto

Search Method to find the correct three-digit code

number for your equipment by following steps:

STEP1 Turn on the equipment that you want the

remote control to operate (Cable Box, TV,

or DVD).

STEP2 Press the [DEVICE] button and the

[OK/SEL] button simultaneously for three

seconds. The device LED will turn on

indicating that it is ready to be

programmed. The LED will remain on for

20 seconds. The next step must be

entered while the LED is on.

STEP3

Press the [CH5] or [CH6] button one at a

time or keep it pressed. The remote will

emit a series of Power ON/OFF code

signals. Release the [CH5] or [CH6]

button as soon as the equipment turns off.

*Note : You can verify that you selected the

correct code by pressing the [MUTE]

button. The equipment should turn On or

Off.

STEP4 Press the same [DEVICE] button to store

the code. The Device LED will blink twice

to confirm that the code has been stored.

E. To find the Three-Digit Code that Was

To find the Three-Digit Code that Was

Programmed using the Auto Search Method

STEP1 Press the appropriate [DEVICE] button

and the [OK/SEL] button simultaneously

for three seconds. The device LED will

turn on for 20 seconds. The next step

must be performed while the LED is on.

STEP2 Press the [INFO] button. The device LED

will blink a number of times indicating the

number of each digit for the code. Each

digit is separated by a one second

interval of the LED being off.

Example : One blink, then three blinks, then eight

blinks indicates the code number 138.

*Note : Ten blinks indicates the number 0.

Programming a Second TV to the DVD Button

STEP1 Press the [DVD] button and the [OK/SEL]

button simultaneously for 3 seconds. The

DVD LED will turn on for 20 seconds. The

next step must be performed while the

LED is on.

STEP2 Press the [TV] button.

STEP3 Point the remote control toward the TV and

enter the three-digit code for your TV from

the TV codes table.

STEP4 Store the three-digit code by pressing the

[DVD] button. The device LED will blink

twice to confirm that the code has been

stored.

G. Programming for Advanced Functions.

In the CABLE device mode, the A,B,C,D and blank

macro buttons can be programmed to act as a

'Macro' or Favorite Channel button. This allows

you to program up to five 2-digit channels, four 3-

digit channels or three 4-digit channels that can

be accessed with ONE button press.

*Note : The A,B,C and D buttons are not

programmable if you have a Digital

Cable Box made by Pace, Pioneer or

Scientific-Atlanta.

STEP1 Press the [CBL] button to select the CBL

mode.

STEP2 Press the [MACRO] button and [OK/SEL]

button simultaneously for 3 seconds. The

[CBL] button will turn on for 20 seconds.

STEP3 Enter the 2, 3 or 4-digit code for the

channel you want programmed first (for

example, 007) using the Number Pad,

then press the [STOP] button. Then enter

the code for the next channel (for

example, 050), then press the [STOP]

button. Repeat this process for the third

channel. The [CBL] button will blink once

for each channel entered.

STEP4 Press the [CH

] button to store the

channels that were selected. The [CBL]

button will blink twice to confirm the

storage of commands.

To access the programmed channels, press

the [MACRO] button once. This will bring up

the first channel. Press once again and it

will bring up the second channel. Press

again and it will bring up the third channel.

To erase the Macro programming and return to

the original function:

STEP1 Press the [CBL] button to select the

CABLE mode.

STEP2 Press a [MACRO] button and the

[OK/SEL] button simultaneously for 3

seconds. The CBL device LED will turn on

for 20 seconds. The next step must be

performed while the LED is on.

STEP3 Press the [CH

] button to erase the

functions stored in the button. The CBL

Otros manuales para Easy Clicker UR3-SR3

Tabla de contenidos

Otros manuales de Mando a distancia de Universal Remote Control

Universal Remote Control

Universal Remote Control UR4U-MDVR2 Manual de usuario

Universal Remote Control

Universal Remote Control Complete Control MX-900i Manual de usuario

Universal Remote Control

Universal Remote Control CLIKR-5 UR5U-8500 Manual de usuario

Universal Remote Control

Universal Remote Control Complete Control MRF-260 Manual de usuario

Universal Remote Control

Universal Remote Control Total Control TRC-1280 Manual de usuario

Universal Remote Control

Universal Remote Control COMPLETE CONTROL MXW-920 Manual de usuario

Universal Remote Control

Universal Remote Control CLIKR-5 UR5U-8500 Manual de usuario

Universal Remote Control

Universal Remote Control Easy Clicker UR2-211 Manual de usuario

Universal Remote Control

Universal Remote Control CLIKR-5 UR5U-8500 Manual de usuario

Universal Remote Control

Universal Remote Control PHAZR-5 UR5U-9000 Manual de usuario

Universal Remote Control

Universal Remote Control MX-5000 Network Wand Manual de usuario

Universal Remote Control

Universal Remote Control UR4-DCT Manual de usuario

Universal Remote Control

Universal Remote Control UR2-DTA Manual de usuario

Universal Remote Control

Universal Remote Control UR2-DTA Manual de usuario

Universal Remote Control

Universal Remote Control URC-A6 Manual de usuario

Universal Remote Control

Universal Remote Control MX-980 Manual de usuario

Universal Remote Control

Universal Remote Control UR3-SR3-DTA Manual de usuario

Universal Remote Control

Universal Remote Control PHAZR-5 UR5U-9000L Manual de usuario

Universal Remote Control

Universal Remote Control MX-500TM Manual de usuario

Universal Remote Control

Universal Remote Control UR-P95TVE Manual de usuario

Universal Remote Control

Universal Remote Control R2-Mini Manual de usuario

Universal Remote Control

Universal Remote Control TeLeCOMMANDE UNIVERSELLE RC 8 Manual de usuario

Universal Remote Control

Universal Remote Control UR-J2000TVE Manual de usuario

Universal Remote Control

Universal Remote Control CLIKR-5 UR5U-8500 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación