Unit UT71B Manual de usuario

Model UT71A/B/C/D/E: OPERATING MANUAL

Unpacking Inspection

Open the package case and take out the Meter. Check the items shown on Table 1-1 carefully to see any missing

or damaged part:

Table 1-1. Unpacking Inspection

Item Description Qty

In the event you find any missing or damage, please contact your dealer immediately.

English Operating Manual

Test Lead

K-Type (nickel chromium ~ nickel silicon) Point Contact Temperature Probe (It is

only suitable for measuring temperature under 230 oC

Alligator Clip

Test Clip

USB interface cable

CD-ROM (Installation Guide & Computer Interface Software)

Carrying Bag

Power Adaptor (UT71E only)

9V Battery (NEDA 1604, 6F22, 006P)

1 piece

1 pair

1 piece

1 pair

1 piece

Model UT71A/B/C/D/E: OPERATING MANUAL

Safety Information

This Meter complies with the standards IEC61010 safety

measurement requirement: in pollution degree 2,

overvoltage category (CAT. III 1000V, CAT.IV 600V)

and double insulation.

CAT. III: Distribution level, fixed installation, with smaller

transient overvoltage than CAT. IV

CAT.IV: Primary supply level, overhead lines, cable

systems etc.

Use the Meter only as specified in this operating manual,

otherwise the protection provided by the Meter may be

impaired.

In this manual, a Warning identifies conditions and

actions that may pose hazards to the user, or may

damage the Meter or the equipment under test.

A Note identifies the information that user should pay

attention to.

International electrical symbols used on the Meter and

in this Operating Manual are explained on page 9.

Rules For Safe Operation

Warning

To avoid possible electric shock or personal injury,

and to avoid possible damage to the Meter or to the

equipment under test, adhere to the following rules:

Before using the Meter inspect the case. Do not

use the Meter if it is damaged or the case (or part

of the case) is removed. Look for cracks or missing

plastic. Pay attention to the insulation around the

connectors.

Inspect the test leads for damaged insulation or

exposed metal. Check the test leads for continuity.

Replace damaged test leads with identical model

number or electrical specifications before using the

Meter.

Do not apply more than the rated voltage, as marked

on the Meter, between the terminals or between any

terminal and grounding.

The rotary switch should be placed in the right

position and no any changeover of range shall be

made during measurement is conducted to prevent

damage of the Meter.

Model UT71A/B/C/D/E: OPERATING MANUAL

When the Meter working at an effective voltage over

60V in DC or 30V rms in AC, special care should be

taken for there is danger of electric shock.

Use the proper terminals, function, and range for

your measurements.

If the value to be measured is unknown, use the

maximum measurement position.

Do not use or store the Meter in an environment of

high temperature, humidity, explosive, inflammable

and strong magnetic field. The performance of the

Meter may deteriorate after dampened.

When using the test leads, keep your fingers behind

the finger guards.

Disconnect circuit power and discharge all high-

voltage capacitors before testing resistance,

continuity, diodes.

Before measuring current, check the Meter's fuses

and turn off power to the circuit before connecting

the Meter to the circuit.

Replace the battery as soon as the battery indicator

appears. With a low battery, the Meter might

produce false readings that can lead to electric

shock and personal injury.

When servicing the Meter, use only the same model

number or identical electrical specifications

replacement parts.

The internal circuit of the Meter shall not be altered

at will to avoid damage of the Meter and any accident.

Soft cloth and mild detergent should be used to

clean the surface of the Meter when servicing. No

abrasive and solvent should be used to prevent the

surface of the Meter from corrosion, damage and

accident.

The Meter is suitable for indoor use.

Turn the Meter off when it is not in use and take out

the battery when not using for a long time.

Constantly check the battery as it may leak when it

has been using for some time, replace the battery

as soon as leaking appears. A leaking battery will

damage the Meter.

Model UT71A/B/C/D/E: OPERATING MANUAL

International Electrical Symbols

Symbols used on the Meter and in this manual are explained in Table1-2.

Table 1-2. International Electrical Symbols

AC or DC

DC Measurement

AC Measurement

Grounding

Double Insulated

Warning. Refer to the Operating Manual

Deficiency of Built-In Battery

Conforms to Standards of European Union

Model UT71A/B/C/D/E: OPERATING MANUAL

Chapter 2

Getting Acquainted

Turning the Meter On

To turn the Meter on, turn the rotary switch from OFF

to any switch setting.

Battery Considerations

The Meter uses one 9V Battery (NEDA 1604, 6F22,

006P). The following paragraphs describe several

techniques used to conserve battery power.

Automatic Power Off

The display blanks and the Meter goes into a "sleep"

mode if you have not changed the rotary switch position

or pressed a button for a set period. While in Sleep

mode, pressing the blue button or turning the rotary

switch could turn the Meter on. The Meter then returns

to the display for the function selected with the rotary

switch; all previously activated button features are

discarded.

Automatic Backlight Off

Press LIGHT button to turn the backlight on and press

LIGHT again to turn it off. Press EXIT to exit the feature.

Press LIGHT to select the backlight level (low or high).

In Setup menu (see Chapter 5), you could specify a

time to automatically turn off the backlight (10 seconds,

20 seconds, 30 seconds or OFF). If the period is set

to OFF, the backlight feature is disabled.

The automatic power off is preset to 10 minutes. From

the Setup menu (see Chapter 5), you could specify a

time (10 minutes, 20 minutes, 30 minutes or OFF). If

you set to OFF, the Meter retains on until you turn the

rotary switch to OFF or the battery becomes too weak.

Model UT71A/B/C/D/E: OPERATING MANUAL

Low Battery Indication

A constant battery icon ( ) in the upper left corner of

the display notifies you that the batteries are low and

should be replaced.

Warning

To avoid false readings, which could lead to possible

electric shock or personal injury, replace the battery as

soon as the battery icon ( ) appears.

The Meter Structure

The Figure 2-1 shows the Meter structure.

1. LCD Display

2. Functional Buttons

3. Rotary Switch

4. Input Terminals

Figure 2-1. Meter Structure

Model UT71A/B/C/D/E: OPERATING MANUAL

Rotary Switch

Turn the Meter on by selecting any measurement function. The Meter presents a standard display for that function.

The display may also be influenced by some of the choices made in Setup.

Use the blue button to select any rotary switch alternate function (labeled in blue letters).

When you turn the rotary switch from one function to another, a display for the new function appears. Button choices

made in one function do not carry over into another function.

The Table 2-1 described each rotary switch position

Model UT71A/B/C/D/E: OPERATING MANUAL

Table 2-1. Rotary Switch Selections

Rotary

Switch Position Rotary Switch Function Blue Key Function

Turn the Meter off

DC voltage measurement

AC voltage measurement

AC or DC voltage measurement

DC millivoltage measurement

Resistance measurement

Power measurement

Capacitance measurement

Centigrade temperature measurement

None

Toggle betweenAC or DC voltage measurement

Frequency measurement

Frequency signal duty cycle measurement

None

Diode test

Continuity test

None

Fahrenheit temperature measurement

OFF

Hz % mV

ºC ºF

(UT71B/C/D)

W (UT71E only)

(UT71B/C/D )

(UT71A/B/C/D )

(UT71E only)

(UT71A/E)

Model UT71A/B/C/D/E: OPERATING MANUAL

Rotary

Switch Position Rotary Switch Function Blue Key Function

Centigrade temperature measurement

AC or DC current measurement (400µA,4000µA)

AC or DC current measurement (40mA,400mA)

AC or DC current measurement (10A)

Fahrenheit temperature measurement

Frequency measurement

Frequency signal duty cycle measurement

Toggle between AC or DC current

4~20mA loop current as % reading

Toggle between AC or DC current

µA

(4~20mA)

(UT71E only)

∫C ∫F

Hz %

Model UT71A/B/C/D/E: OPERATING MANUAL

Functional Buttons

The buttons activate features that augment the function selected with the rotary switch. The buttons are shown

in Table 2-2.

STORE

RECALL

Press the button once to access the main feature (e.g. STORE).

To access the first additional feature of the button (e.g. RECALL), press and hold the button for over 1 second to

access this additional feature. This additional feature appears right above or on the left hand side of the appropriate

keys.

To access the second additional feature of the button (e.g. ), press once the button again while the Meter has

already entered the first additional feature (e.g. RECALL). The second additional feature appears on the right hand

side above the appropriate keys.

The RANGE and EXIT buttons has only one additional feature.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Multímetro de otras marcas

Agilent Technologies

Agilent Technologies 34420A Manual de usuario

Fluke

Fluke 83 Manual de usuario

Hameg

Hameg HM 8012 Manual de usuario

Mastech

Mastech MY70 Manual de usuario

Steren

Steren MUL-300 Manual de usuario

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manual de usuario

PeakTech

PeakTech 4000 Manual de uso y cuidado

YOKOGAWA

YOKOGAWA 90050B Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manual de usuario

Fluke

Fluke 8846A Manual de operación y mantenimiento

Tempo Communications

Tempo Communications MM200 Manual de usuario

Elenco Electronics

Elenco Electronics CM-1555 Manual de usuario

Mastech

Mastech MS8238C Manual de usuario

SDAR

SDAR 830A, 830B, 830D, 830C Manual de usuario

RS PRO

RS PRO RS-9519BT Manual de usuario

BGS technic

BGS technic 8890 Manual de usuario

Amprobe

Amprobe Hexagon 60 Manual de usuario