ULTIMATE SPEED ULSP 2 A1 Manual de usuario

PAINT THICKNESS GAUGE ULSP 2 A1

IAN 91055

PAINT THICKNESS GAUGE

Operating instructions

TESTER STRATURI DE

VOPSEA

Instrucţiuni de utilizare

LACKSCHICHTENPRÜFGERÄT

Bedienungsanleitung

PRÍSTROJ NA MERANIE

HRÚBKY LAKU

Návod na obsluhu

CV_91055_ULSP2A1_SK_RO_OS.indd 2CV_91055_ULSP2A1_SK_RO_OS.indd 2 19.07.13 13:2519.07.13 13:25

GB Operating instructions Page 1

SK Návod na obsluhu Strana 11

RO Instrucţiuni de utilizare Pagina 21

DE Bedienungsanleitung Seite 31

Before reading, unfold the page containing the illustrations and

familiarise yourself with all functions of the device.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte

so všetkými funkciami prístroja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate

funcţiile aparatului.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und

machen Sie sich anschließend mit allen Funktionen des Gerätes

vertraut.

CV_91055_ULSP2A1_SK_RO_OS.indd 3CV_91055_ULSP2A1_SK_RO_OS.indd 3 19.07.13 13:2519.07.13 13:25

CV_91055_ULSP2A1_SK_RO_OS.indd 4CV_91055_ULSP2A1_SK_RO_OS.indd 4 19.07.13 13:2519.07.13 13:25

ULSP 2 A1

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Information concerning these operating instructions . . . . 2

Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Technical details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Information on using batteries . . . . . . . . . . . . . . . . . . . . . 4

Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Initial operation. . . . . . . . . . . . . . . . . . . . . . . . . .5

Inserting/replacing the battery. . . . . . . . . . . . . . . . . . . . . 5

Switching the device on and oﬀ. . . . . . . . . . . . . . . . . . . . 5

Measuring procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Disposal of the device . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Disposing of the batteries. . . . . . . . . . . . . . . . . . . . . . . . . 9

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Importer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

IB_91055_ULSP2A1_SK_RO_OS.indb 1IB_91055_ULSP2A1_SK_RO_OS.indb 1 22.07.13 11:5322.07.13 11:53

2ULSP 2 A1

Introduction

Information concerning these operating

instructions

Congratulations on the purchase of your new device.

You have selected a high-quality product. The operating

instructions are part of this product. They contain important

information on safety, use and disposal. Before using the

product, familiarise yourself with all operating and safety

instructions. Use this product only as described and only for

the speciﬁed areas of application. Retain these instructions

for future reference. Please also pass these operating instruc-

tions on to any future owner(s).

Intended use

This device is exclusively intended for the determination

of paint layer thicknesses on steel surfaces such as cars.

This product is not intended for commercial or industrial use.

The warranty does not provide compensation for damage

caused by improper use of the device!

Package contents

▯ Paint thickness gauge

▯ CR2032 button cell

▯ This operating manual

IB_91055_ULSP2A1_SK_RO_OS.indb 2IB_91055_ULSP2A1_SK_RO_OS.indb 2 22.07.13 11:5322.07.13 11:53

ULSP 2 A1

Technical details

Operating voltage 1 x 3 V battery, type CR2032

Operating temperature 0°C–40°C,

< 80% relative humidity

Dimensions (W x H x D) approx. 4.2 x 6.8 x 1.7 cm

Weight approx. 25 g

Safety instructions

■ Before use, check the device for visible external damage.

Do not use a device that has been damaged or dropped.

■ This device is not intended for use by persons (including

children) with limited physical, physiological or intellectual

abilities or lack of experience and/or knowledge unless

they are supervised by a person who is responsible for

their safety, or receive instructions from this person on

how to use the device.

■ Children should be supervised to ensure that they do not

play with the device.

■ Do not make any unauthorised modiﬁcations or alterations

to the device.

■ Repairs to the device during the warranty period may only

be carried out by a customer service department author-

ised by the manufacturer. Otherwise no additional war-

ranty claims can be considered for subsequent damage.

■ Protect the device from moisture and liquid penetration.

■ The device may not be used in potentially explosive

environments, on surfaces carrying live current or on hot

surfaces (> 70°C).

IB_91055_ULSP2A1_SK_RO_OS.indb 3IB_91055_ULSP2A1_SK_RO_OS.indb 3 22.07.13 11:5322.07.13 11:53

4ULSP 2 A1

Information on using batteries

CAUTION

► Do not throw the batteries into a ﬁre.

► Do not short-circuit the batteries.

► Do not attempt to recharge the batteries.

► Regularly check the condition of the batteries.

Leaking battery acid can cause permanent damage

to the device.

► Special care should be taken when handling a damaged

or leaking battery. Risk of acid burns! Wear protective

gloves.

► Store batteries out of reach of children. If a battery

should be swallowed, seek medical attention

IMMEDIATELY.

► If you do not intend to use the device for a long time,

remove the batteries.

Device description

Protective cap

Measurement sensor

LED display

TEST button

IB_91055_ULSP2A1_SK_RO_OS.indb 4IB_91055_ULSP2A1_SK_RO_OS.indb 4 22.07.13 11:5322.07.13 11:53

ULSP 2 A1

Initial operation

Inserting/replacing the battery

♦ Remove the protective cap and undo the four screws

on the rear of the device.

♦ Remove the rear part of the housing.

♦ Insert a battery of type CR2032 in the battery holder.

Ensure that the polarity is correct: the battery’s positive

terminal should face upwards.

♦ Replace the rear of the housing again using the screws

you previously removed.

NOTE

► When all three LEDs start ﬂashing, the battery needs to

be replaced.

Switching the device on and oﬀ

♦ Remove the protective cap and press the TEST button

for around 3 seconds. The LEDs ﬂash brieﬂy in

succession (RED >> YELLOW >> GREEN). When only the

red LED is ﬂashing, the device is in standby mode.

♦ If no measurement takes place within 20 seconds, the

device switches itself oﬀ automatically. The LEDs

simultaneously ﬂash three times.

♦ Alternatively, you can press the TEST button for

around 3 seconds to switch the device oﬀ manually.

IB_91055_ULSP2A1_SK_RO_OS.indb 5IB_91055_ULSP2A1_SK_RO_OS.indb 5 22.07.13 11:5322.07.13 11:53

6ULSP 2 A1

Measuring procedure

Normal measuring mode

CAUTION

► Place the device carefully on the surface to be meas-

ured, and do not move it during measuring. Remove

the device carefully from the surface after measuring,

otherwise you could cause scratches on the paintwork.

♦ Remove the protective cap and switch the device on

(standby mode).

♦ Keep the device away from any surfaces and then press

the TEST button . The red LED will illuminate perma-

nently and the device is now in normal measuring mode.

♦ Place the measuring sensor at right angles to the

surface to be measured. The measured paint thickness

will be signalised by one of the three LEDs illuminating

(see table).

LED colour Paint thickness

Red > approx. 1.8 mm

Yellow approx. 1.0–1.8 mm

Green < approx. 1.0 mm

♦ Press the TEST button again to return to standby mode.

The red LED ﬂashes.

IB_91055_ULSP2A1_SK_RO_OS.indb 6IB_91055_ULSP2A1_SK_RO_OS.indb 6 22.07.13 11:5322.07.13 11:53

ULSP 2 A1

Reference measuring mode

In this mode, you can compare the paint thicknesses on

various surfaces: for example, on one particular vehicle.

This is useful for determining diﬀerences in paint thicknesses.

For example, you can quickly ﬁnd out whether a surface has

been repainted or ﬁlled.

♦ When the device is in normal measuring mode, place the

measuring sensor at right angles to the surface to be

measured.

NOTE

► The best place to start is the roof of a car, which nor-

mally will not have been repainted or ﬁlled. The paint

coat to be measured must be thinner than 1.8 mm. The

reference measuring mode only works if the yellow or

the green LED is illuminated.

♦ Press the TEST button during the measuring process.

The measured paint thickness is now used as a reference

value. The red and green LEDs will ﬂash alternately.

♦ As soon as you remove the measuring sensor from the

reference surface, the red and the yellow LEDs will ﬂash

alternately.

♦ Now place the measuring sensor on the surface to

be compared: for example, the wing. The LEDs will now

ﬂash in two possible combinations:

IB_91055_ULSP2A1_SK_RO_OS.indb 7IB_91055_ULSP2A1_SK_RO_OS.indb 7 22.07.13 11:5322.07.13 11:53

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios para automóviles de ULTIMATE SPEED

ULTIMATE SPEED

ULTIMATE SPEED 340578 1910 Instrucciones de instalación y funcionamiento

ULTIMATE SPEED

ULTIMATE SPEED 303565 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED 113032 Instrucciones de instalación y funcionamiento

ULTIMATE SPEED

ULTIMATE SPEED 285690 Instrucciones de instalación y funcionamiento

ULTIMATE SPEED

ULTIMATE SPEED UAMM 12 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED RACIN Instrucciones de instalación y funcionamiento

ULTIMATE SPEED

ULTIMATE SPEED UAMM 12 B2 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED USSW 300 B2 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED 322271 Instrucciones de instalación y funcionamiento

ULTIMATE SPEED

ULTIMATE SPEED CLIX I Instrucciones de instalación y funcionamiento

ULTIMATE SPEED

ULTIMATE SPEED RACING Instrucciones de instalación y funcionamiento

ULTIMATE SPEED

ULTIMATE SPEED ULGD 3.8 B1 Manual del propietario

ULTIMATE SPEED

ULTIMATE SPEED UAMM 12 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED UAV 12 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED UAMM 12 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED 316942 Instrucciones de instalación y funcionamiento

ULTIMATE SPEED

ULTIMATE SPEED 1188 1525 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED 279619 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED 91449 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED 340578 1910 Instrucciones de instalación y funcionamiento

ULTIMATE SPEED

ULTIMATE SPEED USWB 22 A2 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULG 3.8 A1 BATTERY CHARGER Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED 340578 1910 Instrucciones de instalación y funcionamiento

ULTIMATE SPEED

ULTIMATE SPEED 292911 Instrucciones de instalación y funcionamiento

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario