Tyco Electronics PRO-CRIMPER III Manual de usuario

Instruction Sheet

PRO-CRIMPER* III Hand

Crimping Tool Ass mbly 58558-1 408-4091

L C B

of 5

2009 Tyco Electronics Corporation, Harrisburg, PA

All International Rights Reserved

TE logo and Tyco Electronics are trademarks.

*Trademark. ther products, logos, and company names used are the property of their respective owners.

T LING ASSISTANCE CENTER 1-800-722-1111

PR DUCT INF RMATI N1-800-522-6752 This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at

www.tyco l ctronics.com

08 MAY 09 Rev B

with Di Ass mbly 58558-2

PROPER USE GUIDELINES

CumulativeTraumaDisorderscanresultfromtheprolongeduseofmanuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume

applications. A wide selection of powered application equipment for extended-use, production operations is available.

The PR -CRIMPER III Hand Crimping Tool is a Commercial" grade tool and

is designed primarily for field installation, repair, maintenance work, or

prototyping in industrial, commercial, or institutional applications. Product

crimped with this tool will meet the crimp height requirement for hand tools in

the appropriate 114 application specification, but may not comply with other

feature parameters of the specification. Tyco Electronics offers a variety of

tools to satisfy your performance requirements. For additional information,

contact the Technical Assistance Center at 1-800-722-1111.

Ratchet

Adjustment

Wheel

PR -CRIMPER III Hand

Crimping Tool Assembly

Frame 354940-1 (408-9930)

Stationary

Handle

Moving

Handle

Stationary

Jaw

Die Assembly

58558-2

Moving

Jaw

Figure 1

Back of Tool

(Wire Side)

Locator and

Straightener

Assembly

1. INTRODUCTION

PRO–CRIMPER III Hand Crimping Tool Assembly

58558–1 consists of Die Assembly 58558–2 and

PRO–CRIMPER III Hand Crimping Tool Frame

354940–1. The hand tool assembly is used to crimp

Consumer RF Series BNC Plug Connectors onto

various sizes of RG/U cable.

For additional information on the hand tool frame,

refer to 408–9930.

Read these instructions thoroughly before using the

hand tool assembly.

Dimensions on this sheet are in millimeters

[with inches in brackets]. Figures are not drawn

to scale.

Reasons for reissue are provided in Section 9,

REVISION SUMMARY.

2. DESCRIPTION

(Figures 1 and 2)

The hand tool assembly features a tool frame with a

stationary jaw and handle, a moving jaw, a moving

handle, and an adjustable ratchet that ensures full

contact crimping. The tool frame holds a die assembly

with four crimping chambers. The die assembly

features an indenter die and an anvil die.

Attached to the outside of the frame is a locator and

straightener assembly, which properly positions and

holds the connector center contact during crimping.

Die retaining pins and die retaining screws are used

to position and secure the dies in the tool frame. A

nut is used on the upper die retaining screw to hold

the locator and straightener assembly in place.

NOTE

408-4091

PRO-CRIMPER III Hand Crimping Tool Assem ly 58558-1

Rev

of 5 Tyco Elect onics Co po ation

Figure 2

Die Retaining

Sc ews

Die Retaining

Pins

Nut

St aightene

Indente

Die

Anvil

Die

Sp ing

Locato

Sp ing

Retaine

Adjustment

Sc ew

3. NSTALLATION AND REMOVAL OF DIE ASSEMBLY

AND LOCATOR AND STRAIGHTENER ASSEMBLY

(Figu e 2)

1. Close the tool handles until the ratchet releases,

then allow the handles to open fully.

2. Remove the two die retaining screws from the

tool jaws.

3. Install the anvil die in the movable jaw of the tool

frame. Insert the short die retaining screw through

the retaining hole in the jaw and through the anvil

die. Tighten the screw just enough to hold the die

in place. Do

not

tighten the screw completely at

this time.

4. Install the indenter die in the stationary jaw of

the tool frame. Insert the long die retaining screw

through the retaining hole in the jaw and through

the indenter die. Tighten the screw just enough to

hold the die in place. Do

not

tighten the screw

completely at this time.

5. Carefully close the tool handles, making sure

that the dies align properly. Continue closing the

tool handles until the ratchet in the tool frame has

engaged sufficiently to hold the dies in place, then

tighten both die retaining screws.

The ratchet has detents that create audible clicks

as the tool handles are closed.

6. Attach the straightener onto the spring retainer

with the adjustment screw. Insert the spring into

the spring retainer and place the locator over the

spring.

7. While holding the locator against the spring

retainer, place the screw hole in the spring retainer

over the end of the long die retaining screw. The

locator should be against the side of the tool jaw.

8. Place the nut onto the end of the long die

retaining screw and tighten the nut enough to hold

the locator and straightener assembly in place, but

still allowing the locator to slide up and down.

9. To disassemble, close the tool handles until the

ratchet releases. Remove the nut, the locator and

straightener assembly, and the two die retaining

screws. Slide the anvil and indenter out of the tool

jaws.

NOTE

408-4091

PRO-CRIMPER III Hand Crimping Tool Ass mbly 58558-1

of 5Rev

Tyco Electronic Corporation

4. CRIMPING PROCEDURE

Th s tool s prov ded w th a center contact support

adjustment and a connector retent on force

forceadjustment feature. In t ally, the center

contact support and the retent on force should be

ver f ed as spec f ed n Sect on 5, CENTER

CONTACT SUPPORT ADJUSTMENT, and

Sect on 6, RETENTION FORCE ADJUSTMENT,

before us ng the tool to cr mp des red connectors.

For detailed information on cable strip lengths and

proper assembly of the connector, refer to the

instructions packaged with the connector. Make sure

that the connector ferrule has been placed onto the

cable, and that the cable braided shield is flared away

from the cable. Then proceed as described in 4.1,

and 4.2.

4.1. Crimping th C nt r Contact

(Figure 3)

1. Holding the center contact by the mating end,

insert the contact through the front of the tool and

into the appropriate crimping chamber of the

anvil die.

2. Close the tool handles so that the dies partially

close. Position the contact so that the locator drops

into the contact wire stop slot and the end of the

contact is inside the groove in the straightener. See

cross–sectional view in Figure 3.

3. Hold the contact in place and squeeze the tool

handles together until the ratchet engages just

enough to hold the contact in place. Do not deform

the contact wire barrel.

4. Insert stripped cable into contact wire barrel until

it is butted against the locator. See cross–sectional

view in Figure 3.

Make sure that both s des of the w re barrel are

started evenly nto the cr mpng chamber. Do

NOT attempt to cr mp an mproperly pos t oned

center contact.

5. Holding the cable in position, close the tool

handles until the ratchet releases. Allow the tool

handles to open fully and remove the crimped

center contact from the dies.

The cr mped center contact may st ck n the

cr mp ng area, but the contact can be eas ly

removed by push ng downward on the top of the

locator (see F gure 3).

4.2. Crimping th F rrul

(Figure 4)

1. Insert the crimped center contact into the

connector body until the cable dielectric butts

against the dielectric inside the connector body or

until the center contact is securely positioned

within the connector. Make sure that the braided

shield is over the support sleeve of the connector

body and that no strands from the shield enter the

connector body.

2. Slide the ferrule up over the braided shield and

onto the connector until the ferrule butts against

the shoulder on the connector body.

3. Place the ferrule in the appropriate crimping

chamber of the anvil die so that the shoulder on

the connector body butts against the edge of

the die.

Figure 3

Cross-Sectional ViewCenter Contact

Crimp

Locator Po itioned

in Contact Wire

Stop Slot

End of Contact

Po itioned in

Straightener

Top of

Locator

Stripped

Cable

Anvil

Die

Center

Contact

Locator

Straightener

Contact

Wire Stop

Slot

Anvil

Die

NOTE

CAUTION

NOTE

408-4091

PRO-CRIMPER III Hand Cr mp ng Tool Assembly 58558-1

Rev

of 5 Tyco Elect onics Co po ation

Figure 4

Ferrule

Crimp

Shoulde on

Connecto Body

Butts Against

Edge of Die

Fe ule in

C imping Chambe

on Anvil Die

Refer to the instruction sheet packaged with the

connector to determine the appropriate crimping

chamber for the ferrule.

4. While holding the assembly together, begin to

close the tool handles. Keep holding the assembly

until the dies have closed enough to hold the

assembly in place.

5. Carefully close the tool handles until the ratchet

releases.

6. Allow the tool handles to open fully and remove

the crimped connector from the dies.

5. CENTER CONTACT SUPPORT ADJUSTMENT

Make a sample crimp and determine if the center

contact is bending upward, bending downward, or

bending from side to side. If the contact is bent,

adjustment is required.

1. Loosen the adjustment screw.

2. Place a center contact with cable into the proper

crimping chamber and close the tool handles until

the locator and straightener assembly is holding

the contact in position.

3. Move the straightener up or down, as required,

to eliminate the bending of the center contact.

4. Tighten the adjustment screw and close the

handles until the ratchet releases.

5. Remove and inspect the center contact.

6. Make another sample crimp. If the contact is still

being bent during crimping, repeat the adjustment

procedure.

6. RATCHET ADJUSTMENT

(Figu e 5)

The frame assembly ratchet mechanism features an

adjustment wheel with numbered settings. If the crimp

height or retention force is not acceptable, adjust the

ratchet as follows:

Refer to the appropriate application specification

(114-series dcument) for the required retention

force for the connector.

1. Remove the lockscrew from the ratchet

adjustment wheel.

2. With a screwdriver, adjust the ratchet wheel

from the opposite side of the frame.

3. Observe the ratchet adjustment wheel. If a

tighter crimp is required, rotate the adjustment

wheel COUNTERCLOCKWISE to a

higher–numbered setting. If a looser crimp is

required, rotate the adjustment wheel

CLOCKWISE to a lower–numbered setting.

4. Replace the lockscrew.

5. Make a sample crimp and measure the crimp

height. If the crimp height is acceptable, secure the

lockscrew. If the dimension is unacceptable,

remove lockscrew and continue to adjust the

ratchet, and again measure a sample crimp.

Figure 5

Sc ewd ive

Ratchet

Adjustment

Wheel

Locksc ew

(Typ)

NOTE

408-4091

PRO-CRIMPER III Hand Crimping Tool Assembly 58558-1

of 5Rev

Tyco Elec ronics Corpora ion

7. MAINTENANCE AND INSPECTION

7.1. Maintenance

1. Remove dust, moisture, and other contaminants

with a clean, soft brush, or a clean, soft, lint–free

cloth. Do NOT use any objects that could damage

the dies or tool.

2. Make sure that the proper die retaining screws

are properly secured.

3. When the dies are not in use, mate and store

them in a clean, dry area.

4. Store the tool with the tool handles closed to

prevent objects from becoming lodged within the

jaws.

7.2. Inspection

1. Remove all lubrication and accumulated film

from the dies by immersing the dies in a suitable

commercial degreaser.

2. Make certain that all die retaining screws and

die components are properly secured.

3. Inspect the crimping surfaces for flattened,

chipped, worn, or cracked areas. If damage is

evident, the dies must be replaced. Refer to

Section 8, DIE REPLACEMENT.

7.3. Measuring the Die Opening

The die assembly will perform correctly as long as:

(1) the product specified is correct for the application,

(2) the specific die assembly is used, (3) the die

assembly has been measured to ensure that the

openings are correct, and (4) the tool has been

adjusted correctly. Figure 6 provides information on

die opening sizes.

8. REPLACEMENT

Customer–replaceable parts are shown in Figure 1.

Available separately, PRO–CRIMPER III Hand

Crimping Tool Repair Kit 679221–1 includes a

replacement nut and a variety of pins, rings, screws,

and springs.

If the dies are damaged or worn excessively, they

must be replaced. Order the repair kit and

replaceable parts through your Tyco Electronics

representative, or call 1–800–526–5142, or send a

facsimile of your purchase order to 1–717–986–7605,

or write to:

CUSTOMER SERVICE (38–35)

TYCO ELECTRONICS

PO BOX 3608

HARRISBURG PA 17105–3608

Note:

No o Scale

DIE CLOSURE DIMENSIONS (+0.10 (+.004])

A B C D

0.89 [.035] 0.79 [.031] 5.28 [.208] 6.10 [.240]

Figure 6

9. RE ISION SUMMARY

Since the previous of this instruction sheet, the

following changes were made:

PRO–CRIMPER II Hand Tool was changed to

PRO–CRIMPER III Hand Tool,

The TE logo was applied, and

The format was updated to the current

corporate requirements.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

TE Connectivity:

58558-1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de Tyco Electronics

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

Tyco Electronics

Tyco Electronics AUTOPRESS C120 Nota de versión

Tyco Electronics

Tyco Electronics PIDG STRATO-THERM 1-576778-0 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

Tyco Electronics

Tyco Electronics ERGOCRIMP 3-1579001-5 Manual de usuario

Tyco Electronics

Tyco Electronics PRO CRIMPER III Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

Tyco Electronics

Tyco Electronics SDE PEW-12 Manual de usuario

Tyco Electronics

Tyco Electronics PRO CRIMPER III Manual de usuario

Tyco Electronics

Tyco Electronics SDE-SA 2063526 Series Manual de usuario

Tyco Electronics

Tyco Electronics 46073 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

Tyco Electronics

Tyco Electronics 58425 Series Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP II Manual de usuario

Tyco Electronics

Tyco Electronics 1213850-1 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

Tyco Electronics

Tyco Electronics AMP SDE PEW 12 Manual de usuario

Tyco Electronics

Tyco Electronics 603995 Series Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

Tyco Electronics

Tyco Electronics 3-1579002-1 Manual de usuario

Tyco Electronics

Tyco Electronics STRATO-THERM 1-46673-0 Manual de usuario

Tyco Electronics

Tyco Electronics 58605-1 Manual de usuario

Tyco Electronics

Tyco Electronics 1490748-1 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

molex

molex 63811-5100 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

molex

molex 63825-3000 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Emerson

Emerson Klauke ES 105CFB Manual de usuario

TE Connectivity

TE Connectivity 539 726-2 Manual de usuario