Trust START-LINE ACM-2300-HC Manual de usuario

USER MANUAL

MULTI LANGUAGE

BUILD-IN SWITCH

Item 71229 Version 1.0

Always read the instructions

before using this product

START-LINE

RECEIVER ACM-2300-HC SWITCH-IN

ACM-2300-HC BUILD-IN SWITCH

5mm

ACM-2300-HC BUILD-IN SWITCH

6c6b

Wall switch

N N S L

Wall switch

N N S L

(

)

N N S LL

(

)

N N S LL

(

)

(

)

(

)

ACM-2300-HC BUILD-IN SWITCH

8c8b

8a7

N N S LL

1 sec

N N S LL

Live

Neutral

Live wire = Brown

Switch wire = Black

Neutral wire = Blue

Switch

ACM-2300-HC BUILD-IN SWITCH

11 12

109

N N S LL

LED

N N S LL

ON - OFF

ACM-2300-HC BUILD-IN SWITCH

N N S LL

A B C

1 sec

OFF

N N S LL

LED

N N S LL

8 sec Shortly

N N S LL

LED

ACM-2300-HC BUILD-IN SWITCH

EN ACM-2300-HC BUILD-IN SWITCH

1. Disable mains power

Always turn OFF the mains power (In the fuse box) before you begin the installation or removal of

this product. The ACM-2300-HC can be used for either two wall switches connected with one lamp

(stairwell/hotel circuit) or for one single wall switch connected to one lamp.

2. Loosen ceiling lights

Remove the existing lighting from the ceiling, leaving the wires connected to the lighting.

Lighting may not exceed the maximum wattage. If there is no live wire (brown) present, it must be

installed. Wire colors may vary per country. Consult an electrician if in doubt about wire colours.

3. Warning for stripping wires

3A. Make sure the wires are stripped for 5mm.

3B. When connecting the wires to the ACM-2300-HC make sure the stripped wires are pressed ﬁrmly

in the module, no exposed wires are visible and the wires cannot touch each other. This can cause

a short circuit.

4. Disconnect the switch wire and neutral wire

To install the ACM-2300-HC disconnect the switch wire (black) and neutral wire (blue) of the lamp

(Disconnect from terminal block or cut the wires if necessary)

5. Connect the live wire to a terminal block

Connect the live wire (brown) from the ceiling box to a terminal block. Connect the other end of the

live wire (brown) also back into the same terminal block.

6A. Connect the wires to the module

• Connect the neutral wire (blue) from the ceiling box to the outer [N] contact of the module

• Connect the switch wire (black) from the ceiling box to the [S] contact.

• Connect the neutral wire (blue) from the lamp to the middle [N] contact.

• Connect the switch wire (black) from the lamp to the [ LL] contact.

• Connect one new live wire (brown) from the live wire (brown) terminal block to the [L] contact.

• Tighten the terminal screws ﬁrmly.

ACM-2300-HC BUILD-IN SWITCH

6B. This is the technical installation schematic of the ACM-2300-HC with two wall-switches (hotel/

stairwell circuit).

6C. This is the technical installation schematic of the ACM-2300-HC with one wall-switch.

7. Installation behind an existing wall switch

Take note how the existing wires are connected and disconnect the wall switch.

• Connect the switch wire (black) from the wall box to the [ LL] terminal.

• Connect the live wire (brown) to a terminal block.

• Connect a new live wire (brown) from the terminal block to the Lcontact.

• Connect a new live wire (brown) from the terminal block to the wall switch (in the place where the

live wire (brown) was previously placed)

• Connect a (blue) neutral wire to the left [N] contact. If there is no neutral wire present, it must be

pulled. Consult an electrician if in doubt.

• Connect a new black switch wire to the S contact and connect it to the wall switch (in the place

where the black switch wire was previously placed)

8A Enable mains power

Switch the mains power ON before proceeding with the installation.

Make sure no stripped parts of wires are touched after this step.

The LED indicator on the receiver will light up for a few seconds when voltage is applied.

8B. Activate pairing mode

Press for about 1 second (with a pointed object) on the Connect button to activate the pairing mode.

The pairing mode will be active for 12 seconds and the LED indicator on the receiver will ﬂash slowly.

8C. Send an ON signal

While the LED indicator ﬂashes, press the ON button on a Trust Smart Home transmitter to pair the

transmitter to the ACM-2300-HC. (Or activate a Trust Smart Home sensor).

9. Pairing conﬁrmation

EN ACM-2300-HC BUILD-IN SWITCH

The LED on the module will blink fast in order to conﬁrm that the code is stored. The receiver can

store up to 32 dierent transmitter codes in its memory. The memory is retained when the receiver is

installed elsewhere or when there is a power failure.

10. Wireless control

Send with the transmitter an ON signal to turn the light on wirelessly.

Send with the transmitter an OFF signal to turn the light o wirelessly.

The existing wall switches which are used to control the connected lighting can still be used.

11. Set the desired switch-o time

Set the switch-o time to the desired position with a ﬂathead screwdriver. The switch-o time can

also be changed after the switch is paired to a Trust Smart Home transmitter.

0m: No OFF signal is sent automatically.

1m, 10m, 1h and 4h: An OFF signal is automatically sent after 1 minute, 10 minutes, 1 hour or 4 hours.

12. Placing the receiver

Place the receiver in the ceiling box. Mount the lights back in place.

Make sure that you can always reach the receiver, for example, to reset it, or to register a new

transmitter.

Make sure no stripped parts of wires touch each other.

Otros manuales para START-LINE ACM-2300-HC

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Cambiar de Trust

Trust

Trust 15919 Manual de usuario

Trust

Trust START-LINE ACC-2300 Manual de usuario

Trust

Trust SMART Home START-LINE RECEIVER ACM-3500-3 Manual de instrucciones

Trust

Trust START-LINE AWMR-230 Manual de usuario

Trust

Trust 411F Manual de usuario

Trust

Trust START-LINE ACM-2000 Manual de usuario

Trust

Trust ACM-3000H2 Manual de usuario

Trust

Trust 73258 Manual de usuario

Trust

Trust Start Series Manual de usuario

Trust

Trust ASUN-650 Manual de usuario

Trust

Trust START-LINE AMU-500 Manual de usuario

Trust

Trust START-LINE AWST-8802 Manual de usuario

Trust

Trust 11670 Manual de usuario

Trust

Trust 300SB Manual de usuario

Trust

Trust HU-3340p Manual de usuario

Trust

Trust 12276 Manual de usuario

Trust

Trust START-LINE AWST-9000Z Manual de usuario

Trust

Trust 12914 Manual de usuario

Trust

Trust 17080 Actualización de firmware

Trust

Trust 12634 Manual de usuario

Trust

Trust HU-4445p Manual de usuario

Trust

Trust ZCC-3500 Manual de usuario

Trust

Trust SMART Home Security Plus-Line AGST-8802 Manual de usuario

Trust

Trust 71075 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario