Trust POWERCAM 922Z Manual de usuario

L I F E I S M O R E ! T R U S T U S T R U S T . C O M

922Z POWERC@M OPTICAL ZOOM

User’s manual

L I F E I S M O R E ! T R U S T U S T R U S T . C O M

922Z POWERC@M OPTICAL ZOOM

Thank you for your purchase. Register your product via our Internet site at

www.trust.com/register, so that you will be eligible for optimal guarantee and service support.

You will also be automatically informed of the development of your and other Trust products.

922Z POWERC@M OPTICAL ZOOM

L I F E I S M O R E ! T R U S T U S T R U S T . C O M

Fig. 1 Fig. 2

Fig. 3 Fig. 4

Fig. 5 Fig. 6 Fig. 7

Fig. 8 Fig. 9

TRUST 922Z POWERC@M OPTICAL ZOOM

1 Introduction

This instruction manual is for users of the TRUST 922Z POWERC@M OPTICAL

ZOOM. This product can be used for (1) making still photo; (2) making macro photo;

(3) making video clip. UK

The built-in memory storage of this camera is 16MB and can be easily expanded by

using a SD (Secure Disk) or MMC (Multi-Media Card) card.

Equipped with a 4cm TFT LCD display, you can see what you just took immediately

or change your camera settings in a minute.

Smart power management combined with a rechargeable Li-Ion battery gives you

extra working hours to record the wonderful moments in your life.

Hold TRUST 922Z POWERC@M, you hold a new world!

2 Safety

Carefully read the following instructions before use.

- The camera does not require any special maintenance. Use a slightly damp,

soft cloth to clean the cover when it gets dusty.

- Keep the glass of the lens clean. Use a cotton bud to clean the lens. If

necessary, use special cleaning liquid for camera lenses. Do not use a

different type of cleaning product. Camera cleaning liquid can be purchased

from photography shops.

- Do not use aggressive substances, such as white spirit, to clean the device.

These may harm the material.

- Do not submerge the device in liquid. This may be dangerous and will

damage the device. Do not use this device near water.

- Do not repair this device yourself nor open this device yourself.

- The camera lens is rather precise component and may be broken by dropping

off, please be careful while handling.

- Do not aim the camera at sun for a long period of time, which may cause

damage to the sensor.

- Exposing the LCD screen to direct sunlight for a long period of time may

cause faults.

- Use only specified battery or AC power adapter (5VDC, 2A) for this camera;

otherwise it can cause fire.

- Fully charge the battery before using. To improve battery performance,

remove the battery from the camera while not using and keep it away from

heat.

- Battery should be inserted in the battery compartment with ‘+’ and ‘-‘ sides

facing correctly.

- Never throw the battery into an open fire. The battery may explode.

TRUST 922Z POWERC@M OPTICAL ZOOM

3 Approval

- This device meets the essential requirements and other relevant conditions of

the applicable European directives. The Declaration of Conformity (DoC) is

available at www.trust.com/13788/ce.

4 Parts and Explanation

Refer on Fig. 1,

Item Description Function

1 Hand strap hook Hook for fixing the hand strap to the

camera.

2 Flash The built-in flash provides more light for

the subject to be photographed.

3 Viewfinder The viewfinder is used to determine the

size and the position of the object of

photograph.

4 Auto Focus LED Used for internal auto focus function.

Turn on ‘RED’ when shoot in dark.

5 Self Timer LED The LED will blink when the 10 seconds

timer is counting down.

6 Zoom Lens Capture the object to be taken.

7 Microphone Used to record the sound.

Table 2: Functions on the front of the camera

Refer on Fig. 2,

Item Description Function

1 Camera power LED (top)

Focus LED (bottom)

- Green when the camera is on.

- Steady green: ready to shot.

Flicker green: auto focusing.

Red: auto focusing failed, adjust

settings

from the object.

2 Display button Change the display mode of the LCD

screen.

3 Zoom button Zoom out of the photograph. (This can be

used to make the photograph look further

away.)

Zoom in on the photograph. (This can be

used to make the photograph look

closer.)

4 5-Way OK Button When you enter the menu mode, use this

shift-stick to select the function from the

menu you want.

Press down OK to confirm your selection.

5 Menu selection button O

en/Close the menu when the camera

TRUST 922Z POWERC@M OPTICAL ZOOM

Item Description Function

is in Capture mode or Playback mode.

6 DC-in & USB connector DC-in, for purchased optional adapter

(5V, 2A). This only supplies power, no

battery charge function.

USB, for making connection to a PC with

supplied USB cable.

7 LCD screen To view the photographs or videos.

To be used as a viewfinder.

To view camera settings, menus.

8 Viewfinder The viewfinder is used to determine the

size and the position of the photograph

being taken.

Table 3: Functions at the rear of the camera

Refer on Fig. 3,

Item Description Function

1 Power button Turn the camera on or off.

2 Shutter button Press this button to take a photograph.

This button is also used to start and stop

recording a video clip.

3 Mode dial Dial for camera operation mode selection.

- Video Mode ( )

- Capture Mode ( )

- Playback Mode ( )

- Macro Mode ( )

- DSC setup Mode ( )

4 Speaker Play sound from the video.

Table 4: Functions on the top of the camera

Refer on Fig. 4,

Item Description Function

1 Docking connection Docking connection for optional cradle.

2 Battery & SD card

compartment

Where you insert the battery or memory

card.

Table 5: Functions at the rear of the camera

Note: The actual photograph is recorded by the lens but not by the

viewfinder. The image may be different from what you see in

viewfinder when the digital zoom is used.

Refer on Fig. 7,

TRUST 922Z POWERC@M OPTICAL ZOOM

Ite

Description Function

1 Protect image In playback mode, to protect

images/videos from being deleted (shift

OK button top).

2 Self timer To take photograph automatically by self-

timer (shift OK button right once!).

3 Continuous shot To take continuous photographs by

pushing shutter button once (shift OK

button right twice!).

4 Delete image In playback mode, to delete stored

images or videos (shift OK button down).

5 Flash settings When taking photograph, to enable or

disable flash (shift OK button left).

Table 6: Meaning of icons around OK button

5 Install battery

5.1 To charge the battery

1. Take out the battery from the camera (or the first time from the box).

2. Place the battery onto the supplied charger.

3. Plug the AC power onto the charger so it starts to charge the battery.

Note: It’s recommended to charge new battery for over 8 hours.

Note: If you plug power without placing battery in the charger, the LED on

the charger turns ‘green’.

Note: If you plug power and place battery into the charger, The LED on the

charger may either turn ‘green’ when battery is fully charged or turn

‘red’ when it’s charging.

Caution: If LED on the charger flickers in red and green after placing battery into

charger, it means the battery is fully charged. Please stop charging.

Caution: The charger or battery is indicated as defective one, if no LED light

turns on while AC power is well connected.

Caution: If battery is not new and has been charged for over 4 hours, but the

LED remains ‘red’. Please stop charging; it indicates the battery is

malfunction.

5.2 Insert battery

See quick install guide point 2 or Fig 5.

Note: Make sure the camera is turned off.

The battery indicator will be displayed at the bottom of the LCD screen when the

camera is turned on.

TRUST 922Z POWERC@M OPTICAL ZOOM

Battery full.

Battery half full.

Battery almost empty.

Battery empty. Recharge the

battery.

Table 1: Battery status on the LCD screen

Note: The battery should be removed if the camera is not going to be used

for some time. This will save the battery power.

Note: It is normal for the camera casing to become warm when using the

camera.

Note: After inserting/replacing the battery, you will have to reset the date and

the time.

6 Taking photograph & video

6.1 Taking photograph

See Quick Install guide point 3.

Note: This camera has smart power management, when you don’t use the

camera for few minutes, it may automatically switch off.

Note: The camera power LED (1, Fig. 2) will turn green when it’s on, and turn

off when camera is off.

6.2 Zoom in/out

This camera has 3x optical zoom plus 4x digital zoom. The zoom bar can be found on

the left side of the LCD display, indicating the zoom status while the zoom in or out

button is pressed; there would be 5 levels of optical zoom magnifications (f0 ~ f6),

from W (wide) to T (Tele) of zoom bar. The zoom lens can automatically protrude and

retract. Then if you keep pressing the zoom button, there would be an additional 8

levels of digital zoom magnification (0.5x/each), from T (Tele) to 4x (4x Digital zoom)

of zoom bar.

1. Once you’ve aligned your subject in the LCD display, press the zoom in or

out button to set your preferred distance.

2. The photograph can be zoomed in up to 12 times the original size.

Hereunder is a table indicating the digital zoom you can use when you take

photograph in certain resolution:

Resolution Digital Zoom

5.5M (2720 x 2040) X 1

3.0M (2048 x 1536) X 4

1.3M (1280 x 960) X 4

VGA (640 x 480) X 4

Table 7: Digital zoom & Resolution

TRUST 922Z POWERC@M OPTICAL ZOOM

Note: 4 x digital zoom are all supported in playback mode!

Note: You are able to see the zoom effect in viewfinder only when using

optical zoom!

6.3 Flash setting

1. Set the camera in either capture or macro mode.

2. Shift the 5-way OK button (4, Fig. 2) to the left to select the desired flash

setting. There are four types of flash settings, as shown in table below

and you can find the icon on left-top corner of LCD display:

Flash off – never flash.

Automatic flash + Red-Eye reduction.

The flash will work automatically when there is insufficient

light and red-eye reduction will also be activated

automatically.

Flash always on.

Night (Slow) – the camera extends the mechanical shutter

action, and allow flash delay.

Table 8: Flash settings

6.4 Taking video clip

First, turn the mode dial to ( ). In this mode, you can use your camera as a

camcorder, or set self-timer for self-recording purpose.

Note: The length of the movie is based on the capacity of your SD card and

the internal memory.

Note: You can still zoom in and out while searching for a subject, but when

the actual recording starts, zooming in and out is not possible any

more.

To record a movie clip, follow steps bellow:

1. Make sure the mode dial is at Video Mode ( ).

2. Point the camera to where you would like to record the movie.

3. Press the shutter button to start the recording.

4. Press the shutter button again to stop the recording.

To set self-timer for automatic self-recording, follow steps below:

1. Make sure the mode dial is at Video Mode ( ).

2. Point the camera to where you would like to record the movie.

3. Shift OK button right once so the self-timer is activated.

4. Press the shutter button to start the recording and the 10 seconds

count down will be displayed in the center of the LCD screen. After 10

seconds, the actual self-recording will start.

5. Press the shutter button again to stop the recording.

TRUST 922Z POWERC@M OPTICAL ZOOM

7 Viewing photograph & video on camera

Note: Do not judge the picture quality on the LCD screen- it is not

precise.

1. Make sure the mode dial is at Playback mode ( ).

2. Press the display button (2, Fig. 2) twice to display the images in

thumbnails in set of nine.

3. Use 5-way OK button to select the image you want.

4. Press down the OK button to confirm the selection and magnify the

image to standard size on LCD screen.

5. Shift the OK button to left or right to view other images.

Note: During the viewing of the images, if you want to do something, press

the menu button (5, Fig. 2) and select the function (see table 13) you

want to do.

Note: The camera has 4x digital zoom that allows you to zoom in the image

up to 4 times its original size in 5 levels. Simply press the Zoom in

button while viewing the image and use 5-way OK button to adjust the

part of the image where you want to magnify on LCD screen.

8 Delete photograph or video on camera

1. Make sure the mode dial is at Playback mode ( ).

2. Press the menu button (5, Fig. 2).

3. Shift the OK button till ‘ ’.

4. Select either to delete Current or All recordings.

9 Install camera driver in Windows 98/98SE

Note: Make sure all other programs are closed during the installation.

Note: In the example, ‘D:\’ is used to indicate the CD-ROM drive. This may be

different for your computer.

Note: Use the language alter box on the top-right corner of Trust installer to

select the language you want to use for installation.

1. Insert the CD-ROM into your computer’s CD-ROM drive. The installation

program will start automatically. If it does not start automatically, carry out

the following:

a) Select 'Run' from the Windows Start menu.

b) Type [D:\SETUP.EXE] and click on 'OK' to start the Trust Software

Installer.

2. The Trust Software Installer will appear (see Fig. 9).

3. Click on “Install driver”.

4. Follow the on-screen instructions to complete the installation.

10 Connecting camera to computer

1. Turn on the computer.

2. Set the camera to Playback mode.

3. Connect the camera to the PC by the USB cable.

4. Turn on the camera.

Tabla de contenidos

Otros manuales de Cámara digital de Trust

Trust

Trust 962Z POWERC@M Manual de usuario

Trust

Trust PowerCam Zoom 920 Manual de usuario

Trust

Trust POWERCAM OPTICAL ZOOM 910Z Manual de usuario

Trust

Trust FlexCam Manual de usuario

Trust

Trust POWERCAM CCD 960 Manual de usuario

Trust

Trust PowerCam Mini DC-3500 Manual de usuario

Trust

Trust 820 LCD POWERC@M ZOOM Manual de usuario

Trust

Trust POWERCAM VIDEO DV-2400V Manual de usuario

Trust

Trust DC-4700 POWERCAM OPTICAL ZOOM Manual de usuario

Trust

Trust 1220S POWERC@M Manual de usuario

Trust

Trust 500F SPYC@M FLASH Manual de usuario

Trust

Trust 782AV Manual de usuario

Trust

Trust FAMILYCAM 510FX Manual de usuario

Trust

Trust 1210K POWERCAM OPTICAL Manual de usuario

Trust

Trust PowerCam Optical Zoom 970Z Manual de usuario

Trust

Trust 740C POWERC@M ZOOM Manual de usuario

Trust

Trust PHOTOCAM LCD 2300 Instrucciones de funcionamiento y mantenimiento

Trust

Trust 1490Z Manual de usuario

Trust

Trust 735 Powercam Zoom Manual de usuario

Trust

Trust 735 POWERC@M ZOOM Manual de usuario

Trust

Trust FAMILYC@M 500 FLASH Manual

Trust

Trust 1290Z Manual de usuario

Trust

Trust 750 LCD POWERC@M ZOOM Manual de usuario

Trust

Trust FAMILYCAM 300 Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario