Trumpf TruTool S 114 Manual de usuario

Operating manual

english

TruTool S 114 (1A1)

2 Table of Contents E582EN_02.DOC

Table of Contents

1. Safety ..................................................................................3

1.1 General safety information...................................................3

1.2 Specific safety information...................................................4

2. Description .........................................................................5

2.1 Intended use ........................................................................5

2.2 Technical specifications.......................................................6

3. Setting work .......................................................................6

4. Operation............................................................................7

4.1 Operating the TruTool S 114 ...............................................8

4.2 Cutting tubes........................................................................9

4.3 Trimming sheets ................................................................10

4.4 Cutting profiles...................................................................11

5. Maintenance .....................................................................12

5.1 Turning or replacing tools ..................................................13

5.2 Replacing carbon brushes.................................................14

6. Original accessories and wearing parts........................15

Guarantee

Replacement parts list

Addresses

E582EN_02.DOC Safety 3

1. Safety

1.1 General safety information

¾Read the operating manual and the safety information

(material no. 1239438, red document) completely before putt-

ing the machine into service. Follow the instructions strictly.

¾Read the operating manual and the safety information

(material number 125699, red document) completely before

putting the machine into service. Follow the instructions strictly.

¾Comply with the safety regulations in accordance with DIN

VDE, CEE, AFNOR as well as any other regulations that apply

in the individual countries.

Danger

Risk of fatal injury from electric shock!

¾Pull the plug from plug socket before undertaking any

maintenance work at the machine.

¾Check the plug, cable and machine for damage each time

before using the machine.

¾Keep the machine dry and do not operate it in damp rooms.

¾Connect the earth leakage (EL) circuit breaker with a

maximum release current of 30 mA when using the electric

tool outside.

Warning

Danger of injury due to improper handling!

¾Wear safety glasses, hearing protection, protective gloves

and work shoes when working at the machine.

¾Do not insert the plug unless the machine is switched off.

After use, pull out the power plug.

USA/CAN

Other countries

4 Safety E582EN_02.DOC

1.2 Specific safety information

Warning

Risk of injury to hands!

¾Do not reach into the processing line with your hands.

¾Do not reach into the space between the oscillating lever and

the abrasive cutting head with your hands or fingers.

Caution

Damage to property due to improper handling!

Machine will be damaged or destroyed.

¾Do not use the power cable to carry the machine.

¾Always position the cable leading away from the machine, at

back of the machine. Do not pull the cable over sharp edges.

¾Have servicing and inspections of hand-held electric tools

carried out by a qualified specialist. Only use original

accessories provided by TRUMPF.

E582EN_02.DOC Description 5

2. Description

1 On/Off switch

2 Oscillating lever

3 Cylindrical pin

4 Fixing screw

5 Blade

6 Cutting head

Trimming shears TruTool S 114

2.1 Intended use

Warning

Danger of injury!

¾Only use the machine for work and materials as described

under "Intended use".

The TRUMPF TruTool S 114 trimming shear is an electrical, hand-

held device used for the following applications:

•Cutting plate-shaped workpieces made of steel, aluminum,

plastic, etc.

•Cutting plate-shaped workpieces made of steel, aluminum,

plastic, etc.

Fig. 46781

6 Setting work E582EN_02.DOC

2.2 Technical specifications

Other countries USA

Values Values Values Values

Voltage 230 V 120 V 110 V 120 V

Frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz

Working speed 4-6 m/min 4-6 m/min 4-6 m/min 13-20 ft/min

Nominal take-up

power 350 W 350 W 350 W 350 W

Idle stroke rate 5800/min 6600/min 6200/min 6600/min

Min. curve

radius 60 mm 60 mm 60 mm 2.36 in

Max. trimming

width 30 mm 30 mm 30 mm 1.18 in

Weight 1.9 kg 1.9 kg 1.9 kg 4.2 lbs

Protective

insulation Class II Class II Class II Class II

Technical data

Permissible material thickness

Steel up to

400 N/mm²

Steel up to

600 N/mm²

Aluminum

250 N/mm²

Standard blade 1.6 mm (0.063 in) 1.0 mm (0.039 in) 2.0 mm (0.079 in)

Noise and vibration Measured values according to

EN 60745

A-class sound pressure level Typically 79 dB (A)

A-class acoustic power level Typically 85 dB (A)

Hand-arm vibration Typically less than or equal to

2.5 m/s²

Measured noise and vibration values

Note

The measured values specified above may be exceeded while

working.

3. Setting work

No settings on the machine are necessary.

Table 1

Table 2

Table 3

E582EN_02.DOC Operation 7

4. Operation

Caution

Damage to property due to high power-supply voltage!

Motor damage.

¾Check the power supply voltage. The power-supply voltage

must correspond to the information on the nameplate of the

machine.

Warning

Risk of injury to hands!

¾Do not reach into the processing line with your hands.

¾Do not reach into the space between the oscillating lever and

the abrasive cutting head with your hands or fingers.

Warning

Danger of injury due to improper handling!

¾Make sure the machine is in a stable position when operating it.

¾Never touch the tool while the machine is running.

¾Always operate the machine away from your body.

¾When working with the machine, wear safety glasses,

protective gloves and work shoes.

Note

Waste metal may arise when machining tubes, profiles and sheets,

which may then become entangled on the abrasive cutting head.

Therefore one should cut tubes in stages and trim sheets in

stages.

8 Operation E582EN_02.DOC

4.1 Operating the TruTool S 114

Note

Do not subject the machine heavy loads to such an extent that it

stops.

To protect the machine and for a good cutting performance:

•Ensure that blades are sharp.

•Replace the blades in due time.

¾Shift the On/Off switch forwards.

1 Opening

Lateral view

¾Shift the On/Off switch to the rear.

Switching on the machine

Fig. 46785

Fig. 46857

Switching off the machine

E582EN_02.DOC Operation 9

4.2 Cutting tubes

1. Place the machine opening around the tube material.

2. Lead the machine diagonally across the tube/sheet.

Fig. 46787

Fig. 46784

10 Operation E582EN_02.DOC

3. Straighten the machine by means of a swiveling motion.

4. For a slightly tapered end to the pipe, lean the machine slightly

towards the center of the tube.

Note

Inclination of the machine prevents the oscillating lever

damaging the walls.

4.3 Trimming sheets

¾Similar procedure as when cutting tubes.

Fig. 46786

Otros manuales para TruTool S 114

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Trumpf

Trumpf

Trumpf TruTool ID 1861 Manual de usuario

Trumpf

Trumpf TKA 300-0 Manual de usuario

Trumpf

Trumpf N 200-5 Manual de usuario

Trumpf

Trumpf TruTool TKA 300 Manual de usuario

Trumpf

Trumpf TruTool N 700 Manual de usuario

Trumpf

Trumpf TruTool TKF 700 Manual de usuario

Trumpf

Trumpf TKA 500-0 Manual de usuario

Trumpf

Trumpf TruTool N 350 Manual de usuario

Trumpf

Trumpf TruTool S 114 Manual de usuario

Trumpf

Trumpf TruTool N 1000 Manual de usuario

Trumpf

Trumpf TruTool C 250 (1B1) Manual de usuario

Trumpf

Trumpf TruTool PN 130 Manual de usuario

Trumpf

Trumpf TruBend 2000 Series Manual de usuario

Trumpf

Trumpf TruTool TF 350 Manual de usuario

Trumpf

Trumpf S 420-0 Manual de usuario

Trumpf

Trumpf TruTool F 125 Manual de usuario

Trumpf

Trumpf TruTool N 700 Manual de usuario

Trumpf

Trumpf N 700-2 Manual de usuario

Trumpf

Trumpf TruTool F 125 Manual de usuario

Trumpf

Trumpf TruTool TF 350 3A5 Manual de usuario

Trumpf

Trumpf TruTool C 250 Manual de usuario

Trumpf

Trumpf TruTool N 160 E Manual de usuario

Trumpf

Trumpf TruTool N 200 Manual de usuario

Trumpf

Trumpf TruTool S 160 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual