Tripp Lite B130-101A-MR Manual de usuario

Owner’s Manual

VGA Over Cat5 Extenders

and Extender/Splitters

Extender Kit Models:

B130-101A-MR and B130-101A-SR

Transmitter Unit Models:

B132-002A-2 and B132-004A-2

Receiver Unit Models:

B132-100A-MR, B132-100A-SR and B132-200A-SR

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

All trademarks are the sole property of their respective owners.

15-04-118-9333BE.indd 1 4/8/2015 10:35:08 AM

Package Contents

B130-101A-MR

B130-101A-SR

B132-002A-2

B132-004A-2

B132-100A-MR

B132-100A-SR

B132-200A-SR

Local Unit (L), Remote Unit (R) or Both (B) B B L L R R R

External Power Supply (P) or Micro USB Cable (U) U U P P U U P

Number of Power Supplies / Micro USB Cables 2 2 1 1 1 1 1

Mounting Hardware Y Y

Screwdriver Y Y Y Y Y

1-ft. VGA + Audio Daisy Chain Cable Y

Table of Contents

Package Contents 2

Product Features 3

All 3

B130-101A-MR 3

B130-101A-SR 3

B132-002A-2 3

B132-004A-2 4

B132-100A-MR 4

B132-100A-SR 5

B132-200A-SR 5

Optional Accessories 5

Mounting Hardware 6

Instructions

Installation 7

EDID Copy 7

Extender Kit Installation 9

Non-Kit Standard Installation 11

Non-Kit Daisy Chain Installation 13

Troubleshooting 16

Warranty and Product 18

Registration

Additional Warnings and 19

Notices

15-04-118-9333BE.indd 2 4/8/2015 10:35:09 AM

Product Features

All

• Transmits both VGA video and mono audio.

• All operating systems supported.

• Plug and play; no software or drivers required.

• HDCP compliant.

B130-101A-MR

• Extends a 1920 x 1080 video signal up to 300 ft. or a 1024 x 768

video signal up to 750 ft.

• Receiver unit features built-in equalization and gain controls to adjust

the video image.

• Power is supplied via the Micro USB ports on the transmitter and

receiver units. No external power supplies required.

• EDID copy feature ensures optimal display compatibility.

B130-101A-SR

• Extends a 1440 x 900 video signal up to 150 ft. or a 1024 x 768 video

signal up to 300 ft.

• Receiver unit features built-in equalization and gain controls to adjust

the video image.

• Power is supplied via the Micro USB ports on the transmitter and

receiver units. No external power supplies required.

• EDID copy feature ensures optimal display compatibility.

B132-002A-2

• Works with the B132-100A-MR, B132-100A-SR and B132-200A-SR

remote units to extend both the VGA video and audio signal.

• Transmits a single VGA video and audio signal to 2 sets of monitors and

speakers.

• Includes mounting hardware that allows unit to be wall-mounted, rack

mounted or pole mounted.

• EDID copy feature ensures optimal display compatibility.

15-04-118-9333BE.indd 3 4/8/2015 10:35:09 AM

B132-004A-2

• Works with the B132-100A-MR, B132-100A-SR and B132-200A-SR

remote units to extend both the VGA video and audio signal.

• Features additional VGA and 3.5 mm ports for connecting a local

monitor and speakers.

• Transmits a single VGA video and audio signal to up to 5 sets

(4 remote, 1 local) of monitors and speakers.

• Expands the number of connected monitors/speakers up to 25

(24 remote, 1 local) by daisy chaining up to 6 local units together.

Note: B132-002A-2 local units cannot be daisy chained.

• Includes mounting hardware that allows unit to be wall-mounted, rack

mounted or pole mounted.

• Up to three local units can be connected to a Tripp Lite B132-004-RB

rackmount bracket and mounted in just 1U of rack space.

• EDID copy feature ensures optimal display compatibility.

B132-100A-MR

• Works with the B132-002A-2 and B132-004A-2 transmitter units to

extend a VGA video and audio signal.

• Extends a 1920 x 1080 video signal up to 300 ft. or a 1024 x 768

video signal up to 750 ft.

• Features built-in equalization and gain controls to adjust the video

image.

• Power is supplied via a Micro USB port. No external power supply

required.

Product Features continued

15-04-118-9333BE.indd 4 4/8/2015 10:35:09 AM

Product Features continued

B132-100A-SR

• Works with the B132-002A-2 and B132-004A-2 transmitter units to

extend a VGA video and audio signal.

• Extends a 1440 x 900 video signal up to 150 ft. or a 1024 x 768 video

signal up to 300 ft.

• Features built-in equalization and gain controls to adjust the video

image.

• Power is supplied via a Micro USB port. No external power supply

required.

B132-200A-SR

• Works with the B132-002A-2 and B132-004A-2 transmitter units to

extend a VGA video and audio signal.

• Features two sets of VGA and audio ports to connect two sets of

monitors and speakers.

• Extends a 1440 x 900 video signal up to 150 ft. or a 1024 x 768 video

signal up to 300 ft.

• Features built-in equalization and gain controls to adjust the video

image.

Optional Accessories

• B132-004-RB 1U Rackmount Bracket

• N022-01K-GY Gray Cat5e Bulk 24 AWG Solid Cable – 1,000 ft.

• N030-010 10-pack of RJ45 Plugs for Solid-wire Cat5e Cable

• N202-Series Cat6 Snagless 24 AWG Solid Patch Cables

• N222-01K-GY Gray Cat6 Bulk 24 AWG Solid Cable – 1,000 ft.

• P312-Series Audio Cables

• P502-Series VGA Monitor Cables with RGB Coax

• P504-Series VGA Monitor + Audio Cables with RGB Coax

• P524-01K Zero-Skew UTP Bulk Cable – 1,000 ft.

15-04-118-9333BE.indd 5 4/8/2015 10:35:09 AM

Mounting Hardware Instructions

The B132-002A-2 and B132-004A-2 units come with mounting

hardware that allows them to be mounted in a variety of ways. The

following images show the different ways the included mounting brackets

can be attached for different mounting methods.

Note: The images below show a B140-101X DVI Extender, but mounting is the

same for the VGA Extenders. The B132-004A-2 can also be mounted to a Tripp Lite

B132-004-RB 1U rackmount bracket. Up to three B132-004A-2 local units can be

connected to a B132-004-RB.

Wall-Mount 1 Wall-Mount 2

19” Rack Mount Pole Mount

15-04-118-9333BE.indd 6 4/8/2015 10:35:10 AM

Installation

EDID Copy

Compatibility issues can occur when EDID information is not properly

communicated between the source and the display. All of the transmitter

units in this manual include an EDID copy feature which stores a

monitor’s EDID information in the transmitter and sends it to the source,

ensuring optimal compatibility.

The transmitter can only store EDID information copied from a single

monitor. You should copy the EDID information of the monitor that

has the lowest maximum supported resolution of all monitors being

connected. This monitor must also support the native video resolutions of

the other monitors.

For example, if you plan to use three monitors that support the

resolutions listed below, you should copy the EDID information from

Monitor A, since the highest resolution it supports is 1440 x 900, which

is lower than the highest supported resolutions of the other two monitors.

Monitor A’s supported resolutions are also supported by Monitors B and C.

A. 1440 x 900, 1024 x 768, 800 x 600

B. 1920 x 1080, 1680 x 1050, 1600 x 1200, 1024 x 768, 800 x 600

C. 1920 x 1080, 1680 x 1050, 1600 x 1200, 1280 x 768, 1152 x 768,

1024 x 768, 800 x 600

If you are not using the EDID copy feature, the transmitter will use a

default set of EDID information.

Note: Receiver units will support EDID copy as long as they are used with a

transmitter unit that supports it.

To use the EDID copy feature, follow the instructions below:

1Determine which monitor to perform EDID copy on, per the example

in the EDID Copy section above.

2If using a B132-002A-2 or B132-004A-2 model, connect the

powered-on monitor to the input port of the transmitter unit. For the

B130-101A-MR and B130-101A-SR, connect the built-in VGA cable

on the transmitter unit to the powered-on monitor.

15-04-118-9333BE.indd 7 4/8/2015 10:35:10 AM

3If using a B132-002A-2 or B132-004A-2 model, connect the

external power supply to the unit and plug it into a Tripp Lite Surge

Protector, Power Distribution Unit (PDU) or Uninterruptible Power

Supply (UPS). For the B130-101A-MR and B130-101A-SR models,

connect the included Micro USB cable to the unit and plug it into the

USB port on a computer or a USB wall outlet. Wait 10 seconds for

the EDID information to be copied, then disconnect the monitor and

proceed per the installation instructions in this manual.

Note: The B130-101A-MR and B130-101A-SR transmitter units feature an internal

EDID LED that blinks to indicate a scan is taking place. The LED will stop blinking

and glow solid when the scan is complete. When a monitor is connected, its EDID

information will be copied and stored on the transmitter unit. If no monitor is

connected, the scan will still take place and the Orange LED will illuminate, but no

EDID information will be copied. The information stored on the transmitter unit will

remain unchanged.

4You can verify that the EDID information was copied from your

computer’s Display Settings screen. If the model name of the monitor

that you copied is shown in the Display ﬁeld, the EDID information

has been copied successfully.

Note: You may need to click on the Detect button.

Installation continued

15-04-118-9333BE.indd 8 4/8/2015 10:35:10 AM

Extender Kit Installation

(B130-101A-MR and B130-101A-SR)

Note:

1. If desired, perform the EDID copy procedure described in this manual prior to

installation.

2. Test to make sure the entire installation works properly before pulling cables

through ceilings/walls.

3. To achieve maximum distance and performance, 24 AWG solid-wire Cat5e/6

cable must be used. The use of stranded wire Cat5e/6 cable, or cable with a

gauge (AWG) size higher than 24 AWG will result in shorter extension distance.

All Tripp Lite N202-Series cables are made with 24 AWG solid-wire cabling.

Tripp Lite N022-01K-GY (Cat5e) and N222-01K-GY (Cat6) are 24 AWG solid-wire

bulk cables. For optimal image quality, use Zero-Skew cable such as Tripp Lite

P524-01K.

1Make sure the VGA and audio source is powered off.

2Connect the built-in VGA cable of the transmitter unit to the

computer’s VGA port.

3Connect a 3.5 mm audio cable from the transmitter unit to the

computer.

4Connect the included Micro USB cable between the transmitter unit

and a USB port on the computer or USB wall outlet.

5Using Cat5e/6 cable, connect the RJ45 OUTPUT port of the

transmitter unit to the RJ45 INPUT port of the receiver unit (see

Product Features section for your model’s max distance information).

6Connect the built-in VGA cable of the receiver unit to the monitor’s

VGA port.

Installation continued

Transmitter Unit Receiver Unit

15-04-118-9333BE.indd 9 4/8/2015 10:35:10 AM

Installation continued

7Connect a 3.5 mm audio cable from the receiver unit to the monitor

or external speakers.

8Use the included Micro USB cable to connect the receiver unit with a

USB port on the monitor or USB wall outlet.

9Turn on the power to the computer, monitor and speakers.

10 If necessary, adjust the equalization and gain controls on the receiver

unit with the included screwdriver to improve the video image.

15-04-118-9333BE.indd 10 4/8/2015 10:35:10 AM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Extensor de Tripp Lite

Tripp Lite

Tripp Lite B136-004 Manual de usuario

Tripp Lite

Tripp Lite B203-101-IND-ER Manual de usuario

Tripp Lite

Tripp Lite B132-004A Manual de usuario

Tripp Lite

Tripp Lite B126-1D10-WHD1 Manual de usuario

Tripp Lite

Tripp Lite B013-HU-4K Manual de usuario

Tripp Lite

Tripp Lite B125-150 Manual de usuario

Tripp Lite

Tripp Lite P142-06N-SC4K Manual de usuario

Tripp Lite

Tripp Lite B127U-111-PHPH Manual de usuario

Tripp Lite

Tripp Lite B127M-101-H Manual de usuario

Tripp Lite

Tripp Lite 0DT23008 Manual de usuario

Tripp Lite

Tripp Lite B140-002-DD Manual de usuario

Tripp Lite

Tripp Lite B127-008-D Manual de usuario

Tripp Lite

Tripp Lite B203-101 Manual de usuario

Tripp Lite

Tripp Lite B164-101-WIR Manual de usuario

Tripp Lite

Tripp Lite B125-101-60-WP Manual de usuario

Tripp Lite

Tripp Lite B130-101S-WP Manual de usuario

Tripp Lite

Tripp Lite B127A-4X1-BH Manual de usuario

Tripp Lite

Tripp Lite B136-101 Manual de usuario

Tripp Lite

Tripp Lite U224-1R4-R Manual de usuario

Tripp Lite

Tripp Lite B013-330 Manual de usuario

Tripp Lite

Tripp Lite B120-000-SL Manual de usuario

Tripp Lite

Tripp Lite B162-100-POE Manual de usuario

Tripp Lite

Tripp Lite B203-101-POC Manual de usuario

Tripp Lite

Tripp Lite B013-000 Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario