Triplett RHT45 Manual de usuario

User Manual

RHT45

Digital Psychrometer

Introduction

Congratulations on your purchase of the Triplett RHT45 Digital

Psychrometer. This meter serves as a very valuable HVAC diagnostic tool.

It measures wet bulb (WB), dry bulb (DB), percent relative humidity (RH%),

and dew point (DP) which allows for quick and easy diagnostic of airflow

problems. Specialized modes include NORMAL Psychrometer Mode,

Target Superheat Mode (TSH) and Target Evaporator Exit Temperature

Mode (TEET) .

Safety

Do not operate the meter in environments where the following are

present: explosive gases (or materials), combustible gases (or

materials), steam, or dust.

Please replace the battery immediately when the low battery symbol

appears on the LCD.

Do not touch the meter’s circuit board for any reason; static

electricity or contamination could damage the sensitive

components.

This instrument was designed for pollution

degree 2. Operation Altitude: Up to 2000m

(7000’).

Description

1. Type K Thermocouple Input

2.NTC Sensor

3.MODE Button

4.Enter Button

5.OUTPUT Button

6.°F/°C Button

7.Sensor Button

8.MAX/MIN/HOLD Button

9.ON/OFF Button

10.LCD Display

11..Air Humidity and Temp Sensor

12..Battery Cover

Display

1. Low Battery Indicator

2. RH/DP/WB/DB Indicator

3. °F/°C Indicator

4. Indoor/Outdoor Indicator

5. Upper Display –Displays Measurement Value

6. MAX/MIN Indicator

7. Humidity Indicator

8. Hold Mode Indicator

9. T/C or NTC Indicator

10. Mode Select Indicator

11. APO Indiicator

12. Lower Display –Displays Target Superheat and Target Evaporator

Exit Temp

13. °F/°C Indicator

How it Works:

This meter has three sensors. One for RH% and two for temperature.

Depending on where you place these sensors and how you set up the meter.

The meter will display the measurements and the results of calculations from

these inputs.

Inside the ‘cage’on the top of the meter is a thermistor, right next to the RH%

sensor. It’s used to measure ambient air(DB).In addition to the thermistor, a

thermocouple can be plugged into the temperatures (including wet bulb) in hard

to reach places. such as in front or in back of the evaporator coil.

To use this meter, you must tell it what test you want it to perform. Select the

parameter you want to measure, and choose which temperature sensor to use,

either the thermocouple (T/C) or the ‘caged’thermistor (NTC). Take your

measurements. Read the results, both the directly measured readings and the

calculated results.

Operation

Normal Psychrometer Mode

Turn the Meter ON by pressing the button ,Select NORM by

pressing “MODE”button until NORM is displayed in the LCD.

Press the “SENSOR” button and holding for 2s to select

temperature sensor: T/C for thermocouple, NTC for sensors in the

‘cage’.

For T/C, the display will show the temperature .For NTC, press the

“SENSOR” button to select RH, DP, WB, DB mode and the desired

icon (RH,DP,WB,DB) is displayed. Then read the display.

Target Superheat Mode(TSH)

（1）.Turn the Meter ON by pressing the button ,Select TSH by pressing

“MODE”button until TSH is displayed in the LCD.

* Note: blinking numbers mean you are seeing real-time measurements.

Non-blinking mean the reading has been ‘locked in ’.Press ENTER button

to unlock and take a new reading. *

（2）.The more accurate method:

a. Wet the thermocouple A.Clip it to the front of the evaporator coil. Plug it

into the top of the meter. Make sure the display show ID and WB. If not, press

the “SENSOR”button. Press and holding the “SENSOR”button until T/C is

displayed. Once the reading is stable, press ENTER button.

b. Unplug the thermocouple A and plug in the thermocouple B.

c. Clip the thermocouple B to the side of the condenser. Press “SENSOR”

button until OD and DB are displayed. Once reading is stable, press ENTER.

*Note: for DB, you can put the ‘cage’sensors in front of the condenser and

select NTC if that is easier.

The easy way: While the numbers are blinking, press and holding

“SENSOR”button until NTC is displayed. Press “SENSOR”button until

WB or DB is displayed. When WB is displayed, place the ’cage’sensors in

front of the indoor return and press ENTER button once reading is stable.

When DB is displayed, put the ‘cage’sensors in front of the condenser

and press ENTER button when the reading is stable.*

（3）. Press OUTPUT button to display Target Superheat.

（4）. Compare Target Superheat to Actual Superheat.

（5）. Adjust refrigerant levels accordingly for a fixed restrictor system. If

Actual Superheat is higher than Target Superheat, add refrigerant. If Actual

Superheat is lower than Target Superheat, recover refrigerant.

Target Evaporator Exit Temperature (TEET)

(1). Turn the Meter ON by pressing the button , Select TEET by pressing

“MODE” button until TEET is displayed in the LCD.

Note: blinking numbers mean you are seeing real-time measurements. Non-

blinking mean the reading has been ‘locked in ’.Press ENTER button to unlock

and take a new reading.

(2). Wet the thermocouple A wet sock thermocouple and clip both

thermocouples (thermocouple A and thermocouple B) in front of the evaporator.

(3). Plug the thermocouple A into the top of the meter.

Note: If “OL” is displayed, then the measurements are out of range. Retake

the temperature measurements and ensure the temperature inputs are correct.

(4). Press “SENSOR”button until WB is displayed. Press and holding

“SENSOR” button until T/C is displayed. When reading is stable, press ENTER

button.

(5). Unplug the thermocouple A and plug in the thermocouple B.

（6）.Press “SENSOR”button until DB is displayed. Press and holding

“SENSOR” button until T/C is displayed. When reading is stable, press ENTER

button

（7）.Press OUTPUT button and read Target Evaporator Exit Temperature.

Note: If “OL” is displayed, then the measurements are out of range. Retake

the temperature measurements and ensure the temperature inputs are correct.

（8）. Compare Target Evaporator Exit Temperature to Actual Evaporator Exit

Temperature. The Actual Evaporator Exit Temperature is the measured

temperature of the air after it has passed through the evaporator.

（9）. Adjust airflow accordingly. An Actual Evaporator Exit Temperature. That

is below the Target Evaporator Exit Temperature. Is indicating a low airflow.

Increasing airflow can be accomplished by eliminating restrictions in the duct

system, increasing blower speed, cleaning filters or opening registers. An Actual

Evaporator Exit Temperature that is above the Evaporator Exit Temperature

.usually indicates low capacity. Occasionally airflow is higher than expected.

Look for causes of low capacity such as refrigerant mischarge or a dirty

condenser coil. If the airflow is high, correct it by lowering the fan speed.

Note: If “OL” is displayed, then the measurements are out of range. Retake

the temperature measurements and ensure the temperature inputs are correct.

IMPORTANT TO NOTE::

Because everything within the system is interdependent, one adjustment can

affect other parts of the system. For example, increasing airflow increases the

superheat, which may require adding refrigerant. After any modifications, allow

15 minutes to stabilize and then retest. For the best results take measurements

right after each other.

Select °C or °F

Turn the Meter ON by pressing the button , Select °C or °F by pressing

“C/F”button until °C or °F is displayed in the LCD. Press and holding “C/F”

button for 2s to select backlight on or off.

Auto-Power-Off (APO)

This meter shall enter a sleep mode after 15 minutes of inactivity,

Pressing the “MAX/MAIN” button while turning the meter from OFF to ON

shall cause the APO to be disabled, and the APO icon to be turned off.

Battery replacement

Turn off the instrument.

Remove the battery cover

Replace the battery.

Install the battery cover

Specifications

WARNING

If the symbol “ ” appears on the LCD,

please replace the battery immediately

Type K. Range

-50℃to 1372℃(-58℉to 2501℉)

Type K.Accuracy:

±[0.5% rdg +1℃( 1.8℉)]

Type K.

Resolution

0.1°(<1000) or 1°(>=1000)

Warranty Information

Triplett / Jewell Instruments extends the following warranty to the original purchaser of

these goods for use. Triplett warrants to the original purchaser for use that the products sold

by it will be free from defects in workmanship and material for a period of (1) one year from

the date of purchase. This warranty does not apply to any of our products which have been

repaired or altered by unauthorized persons in any way or purchased from unauthorized

distributors so as, in our sole judgment, to injure their stability or reliability, or which have

been subject to misuse, abuse, misapplication, negligence, accident or which have had the

serial numbers altered, defaced, or removed. Accessories, including batteries are not

NTC. Range

0℃to 60℃(32℉to 140℉)

NTC.Accuracy

±1℃( 1.8℉)

NTC . Resolution

0.1°

Wet Bulb and

Dew Point Temp

Range

32°F to 140°F (0℃to 60℃)

Relative Humidity

0% to 100% RH range

Accuracy

±2.5%RH(10% to 90%RH)

±5%RH(0 to 10%RH or 90 to 100%RH)

Operating

Temperature

32°F to 122°F (0℃to 50℃)

Storage

Temperature

14°F to 140°F (-10℃to 60℃)

Tabla de contenidos

Otros manuales de Instrumento de medición de Triplett

Triplett

Triplett LT75 Manual de usuario

Triplett

Triplett RHT22 Manual de usuario

Triplett

Triplett TA150 Manual de usuario

Triplett

Triplett 630-NA Manual de usuario

Triplett

Triplett AM320 Manual de usuario

Triplett

Triplett GSM120 Manual de usuario

Triplett

Triplett PR600 Manual de usuario

Triplett

Triplett GSM400 Manual de usuario

Triplett

Triplett SoniChek MC Manual de usuario

Triplett

Triplett 9200-A Manual de usuario

Triplett

Triplett CFM400 Manual de usuario

Triplett

Triplett GSM250 Manual de usuario

Triplett

Triplett EPC175 Manual de usuario

Triplett

Triplett RHT05 Manual de usuario

Triplett

Triplett DPR302 Manual de usuario

Triplett

Triplett LT65 Manual de usuario

Triplett

Triplett RHT37 Manual de usuario

Triplett

Triplett 2030-C Manual de usuario

Triplett

Triplett LT68-NIST Manual de usuario

Triplett

Triplett 630 Manual de usuario

Triplett

Triplett CamView W35 Manual de usuario

Triplett

Triplett CM1050 Manual de usuario

Triplett

Triplett CM400 Manual de usuario

Triplett

Triplett 9200B Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario