Trinity Basics THA-0307 Manual de usuario
OWNER’S MANUAL
Important / Important / Importante
DOWNLOAD THE FREE APP | TÉLÉCHARGER L’APPLICATION GRATUITE| DESCARGUE LAAPLICACIÓN GRATUITA
Directives intelligentes
Instrucciones Inteligentes
FOR QUICK & EASY 3D ASSEMBLY INSTRUCTIONS
POUR DES DIRECTIVES D’ASSEMBLAGE 3D RAPIDES ET FACILES
PARA INSTRUCCIONES DE ENSAMBLAJE RAPIDAS Y SENCILLAS EN 3D
TRINITY BASICS STAINLESS STEEL UTILITY SINK W/ FAUCET
Model # THA-0307
Your TRINITY Basics Stainless Steel Utility Sink w/Faucet should include the following parts. Please
inspect box contents to ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions, please contact TRINITY
Customer Service: 800.985.5506 or customerservice@trinityii.com. Parts can also be requested online
via our “Contact Us” section at www.trinityii.com.
A Phillips head screwdriver is required for assembly, and a pipe wrench is recommended.
SINK (1)
A
LEG (4)
W/ FEET LEVELER
BC
HEX KEY (1)
FAUCET ASSEMBLY (1)
W/ HOSES
DRAIN ASSEMBLY (1)
F
HEX SCREW (8) + (2) extra
(8) are pre-installed on sink,
(2) extras are packed in the hardware bag
G
EH
I
BRACKET (1)
MOUNTING SCREW (2) ANCHOR (2)
© 2020 TRINITY - 800.985.5506 1
PARTS LIST
D
SCREW CAP (8)
J
ASSEMBLY INSTRUCTIONS
Carefully turn sink right-side up, standing it
upright.
Unscrew large 3-3/8” Nut from bottom of
DRAIN ASSEMBLY (D). From inside SINK (A),
insert Drain through White Seal and opening
at bottom.
From under SINK (A), first slide on Black
Gasket and Paper Washer then screw large
3-3/8” Nut back on tightly. If necessary, use
a pipe wrench to tighten.
Note: P-trap NOT included.
Lay SINK (A) upside-down. Unscrew HEX
SCREWS (E) that are pre-installed on Leg
Collars on bottom of SINK (A) until LEGS (B)
can be fully inserted.
Insert LEGS (B) into Leg Collars. Tighten both
HEX SCREWS (E) on each Leg Collar with HEX
KEY (G). Place a SCREW CAP (F) over each
HEX SCREW (E).
STEP 1
STEP 2
E (8) G (1)
B (4)
B
A
A (1)
D
EG
D (1)
Leg Collar
© 2020 TRINITY - 800.985.5506
2
Drain Assembly (D)
F (8)
F
E
Inside
the sink
Under
the sink
Drain
Black
Gasket
Paper
Washer
3-3/8”
Nut
White
Seal
ASSEMBLY INSTRUCTIONS
Unscrew each screw securing Lock Nut to
bottom of FAUCET ASSEMBLY (C) and remove
Lock Nut w/Screws, Metal Washer and
Rubber Gasket.
From top side, insert FAUCET ASSEMBLY (C)
through hole. Make sure Metal Base is on top
of SINK (A). Align faucet handle facing
towards front of SINK (A). From under SINK
(A), first slide on Rubber Gasket, then Metal
Washer, and lastly, screw on Lock Nut
w/Screws pointed upward. Tighten Lock Nut
as much as you can by hand and tighten
screws with a screw driver.
STEP 3
C (1)
C
On top of
the sink
Under
the sink
Faucet
Metal
Base
Rubber
Gasket
Lock Nut
w/ Screws
Carefully move sink against wall at your desired
location. If needed, use a pencil to mark off
mounting height of BRACKET (H).
Position BRACKET (H) on wall, marking off
fastening location on wall through holes on
BRACKET (H). Drill holes in marked locations.
Insert ANCHOR (J) completely into each drilled
hole. Fasten MOUNTING SCREWS (I) through
these holes into wall or anchors tightly with
a screwdriver.
Slightly lift sink and hook flange of sink over
BRACKET (H). Adjust Feet Levelers to ensure sink
is stable and level. Connect Hoses and Drain to
plumbing system.
Note: Bracket is to prevent sink tipping, NOT for
mounting sink to a wall. Do NOT mount sink to a
wall without legs.
STEP 4
H (1) I (2) J (2)
H
I
J
flange
H
© 2020 TRINITY - 800.985.5506 3
Faucet Assembly (C)
Metal
Washer
SERVICE PARTS LIST
Part Number Description Part Number Description
1) XBS-19-007-1600 Bracket 7) XGR-98-005-3775 Feet Leveler
2) XGR-01-032-0440 Anchor 8) XSV-01-034-0808 Hex Screw
3) XSV-01-033-0440 Mounting Screw 9) XXX-97-001-0001 Hex Key
4) XBS-18-023-1816 Sink 10) XGL-02-003-0002 Drain Assembly
5) XBK-23-005-0815 Screw Cap 11) CGL-02-009-0003 Faucet Assembly
6)
XGL-04-045-1950 Leg
TRINITY Customer Service provides the following replacement parts:
5
2
10
8
1
3
6
9
4
11
© 2020 TRINITY - 800.985.5506
4
7
WARNINGS
1. Read and understand all instructions. Failure to follow all instructions may result in injury
and/or damage.
2. The warnings, cautions, and instructions discussed in this manual cannot cover all
possible conditions or situations that may occur. The user must always be aware of their
environment and ensure that they use the product in a safe and responsible manner.
3. Do NOT modify the product in any way. Unauthorized modification may impair the
function and/or safety of the product, and may affect the life of the product. Any
modifications will void product warranty.
4. Check for damaged parts. Before using this product, carefully check that all parts are in
good condition, and that the product will operate properly and perform its intended
function. Check for damaged parts and any other conditions that may affect the operation
of this product. Replace damaged or worn parts, and never use this product with a damaged
part.
5. Do NOT overload the product.
6. Ensure backflow prevention compliance. Equipment is to be installed with adequate
backflow prevention to comply with applicable federal, state and local codes.
7. Do NOT let children climb on or in Utility Sink.
8. Ensure to install the wall bracket. Failure to do so may result in tipping.
9. Do NOT mount the sink to a wall without legs. The wall bracket is to prevent tipping, NOT
for mounting the sink to a wall.
10. Ensure plumbing connections are tightened fully. Failure to tighten may result in leakage.
11. Strongly recommended for professional installers to perform installation. Observe local
plumbing and building codes.
Total weight capacity 300 lb
© 2020 TRINITY - 800.985.5506 5
© 2020 TRINITY - 800.985.5506
6
CARE AND MAINTENANCE
•Avoid harsh, abrasive cleaners, and other corrosive chemicals. Do not leave salt in sink or
near saltwater environment.
•Rinse surface thoroughly with hot water after using soaps and detergents containing
chlorides to prevent corrosion.
•Do not use scouring pad, carbon steel brushes, or steel wool for cleaning. Iron particles left
behind can lead to rust.
•Avoid the use of oily rags or greasy cloths when wiping the surface. Wipe dry after use so
that water does not leave water spots.
•Use a quality stainless steel cleaner and follow instructions that come with the cleaner.
Wipe ALONG the grain (NOT against).
Thank you for purchasing a TRINITY Basics Stainless Steel Utility Sink w/Faucet. In order to register
your product and receive streamlined customer service, please fill out the following Product
Registration Form and (1) fax the form to 310.347.4134 (2) complete the Product Registration Form
online at www.trinityii.com or (3) scan and email the form to customerservice@trinityii.com. Include a
copy of your original receipt with your submission.
First Name: Last Name:
Address:
City: State: Zip Code:
Email Address: Phone:
Product Model #: THA-0307 Purchase Date: / /
Location of Purchase:
Please rate the importance of each feature (1=least important; 10=most important)
Quality Price Size/Capacity Appearance Other
How did you hear about our product?
Magazine Ad Catalog Salesperson Word of Mouth
Internet Store Display Other
Marital Status: Single Married
Household Income: Below $50,000 $50,000-$150,000 $150,000+
Education: High School College Graduate School
Primary Residence: Own Rent
Comments/Suggestions:
PRODUCT REGISTRATION
© 2020 TRINITY - 800.985.5506 7
© 2020 TRINITY - 800.985.5506
8
Tabla de contenidos
Otros manuales de Producto de plomería de Trinity Basics
Manuales populares de Producto de plomería de otras marcas
Weka
Weka 506.2020.00E Instrucciones de funcionamiento
Kohler
Kohler K-6228 Instrucciones de montaje
UBERHAUS DESIGN
UBERHAUS DESIGN 75175017 Manual de usuario
American Standard
American Standard DetectLink 6072121 Manual de usuario
Uponor
Uponor Contec TS Manual de usuario
Pfister
Pfister Selia 49-SL Manual de usuario
