Trikdis GV17 Manual de usuario

www.trikdis.com  UAB Trikdis  Draugystės str. 17, LT-51229 Kaunas, Lithuania  +370 37 408 040  inf[email protected]

GSM gate controller GV17

Installation manual

November 2018

www.trikdis.com 2 November, 2018

GSM gate controller GV17

Contents

SAFETY PRECAUTIONS ........................................................................................................................ 3

1 DESCRIPTION .................................................................................................................................. 4

1.1 SPECIFICATIONS ...................................................................................................................................... 5

1.2 CONTROLLER ELEMENTS ........................................................................................................................... 5

1.3 PURPOSE OF TERMINALS .......................................................................................................................... 6

1.4 LED INDICATION OF OPERATION ................................................................................................................ 6

1.5 GSM GATE CONTROLLER GV17 STANDARD PACKING LIST ............................................................................... 7

2 WIRING SCHEMATICS FOR THE GSM GATE CONTROLLER GV17 ......................................................... 7

2.1 FASTENING ............................................................................................................................................ 7

2.2 SCHEMATIC FOR CONNECTING THE POWER SUPPLY ......................................................................................... 8

2.3 SCHEMATICS FOR CONNECTING INPUTS ........................................................................................................ 8

2.4 SCHEMATIC FOR CONNECTING THE RELAY ..................................................................................................... 8

3 QUICK SET UP OF THE CONTROLLER ................................................................................................. 9

4 REMOTE CONTROL .......................................................................................................................... 9

4.1 CONTROL WITH PHONE CALL ..................................................................................................................... 9

4.2 CONTROL WITH PHONE KEYBOARD.............................................................................................................. 9

4.3 CONTROL USING PROTEGUS CLOUD .......................................................................................................... 10

4.4 CONTROL WITH SMS MESSAGES .............................................................................................................. 12

4.5 CONFIGURATION WITH SMS MESSAGES .................................................................................................... 13

5 SETTING PARAMETERS USING TRIKDISCONFIG SOFTWARE .............................................................. 15

5.1 TRIKDISCONFIG STATUS BAR .................................................................................................................... 16

5.2 “SYSTEM OPTIONS” WINDOW ................................................................................................................. 16

5.3 “IN/OUT” WINDOW ............................................................................................................................ 17

5.4 “IP REPORTING” WINDOW ..................................................................................................................... 18

5.5 “USER LIST” WINDOW ........................................................................................................................... 19

5.6 “EVENTS LOG” WINDOW........................................................................................................................ 21

5.7 RESTORE DEFAULT SETTINGS ................................................................................................................... 22

6 SETTING PARAMETERS REMOTELY ................................................................................................. 22

7 TESTING OF GSM GATE CONTROLLER GV17 .................................................................................... 22

8 UPDATING FIRMWARE MANUALLY................................................................................................. 23

www.trikdis.com 3 November, 2018

GSM gate controller GV17

Safety precautions

The GSM gate controller should only be installed and maintained by qualified personnel.

Please read this manual carefully prior to installation in order to avoid mistakes that can lead to

malfunction or even damage to the equipment.

Always disconnect the power supply before making any electrical connections.

Any changes, modifications or repairs not authorized by the manufacturer shall render the warranty void.

Please adhere to your local waste sorting regulations and do not dispose of this equipment or its

components with other household waste.

www.trikdis.com 4 November, 2018

GSM gate controller GV17

1 Description

GSM gate controller GV17 can remotely control automatic gates and other equipment.

Users can control GV17 with Protegus application, telephone calls and SMS messages. The controller can

recognize up to 7 administrator and 990 user telephone numbers. A user control schedule and counter for

how many times a specific user can control the system can be set for the GV17. The GSM controller can

send SMS messages informing when inputs and outputs are activated and restored (the text of the SMS

messages is customizable). The controller is capable of sending event messages to the receiver of a security

company.

Features

Remote control

 With Mobile/Internet application Protegus.

 With SMS messages.

 With phone call.

Messages for users

 Sends messages about events to the

Protegus application or with text SMS

messages.

Messages for the safety company

 Sends event information in Contact ID codes

to TRIKDIS software and hardware receivers,

which work with any monitoring software.

 Can simultaneously send event messages to

the receiver of the safety company and work

with the Protegus app.

 If connection with the main receiver is lost,

the messages are automatically sent to a

backup receiver.

Inputs and outputs

 2 inputs (IN), of selectable type: NO; NC;

EOL.

 2 universal inputs/outputs. Mode of

operation is set as either input or output.

 1 output (OUT) - relay.

Settings and installation

 Quick and easy installation.

 Addition of new users and deletion of

existing users can be done with the Protegus

app (when logged in with administrator

rights), SMS message, TrikdisConfig

software.

 Device can be configured either by

connecting a USB Mini-B cable or remotely

with the TrikdisConfig software.

 Remote updating of firmware.

 Two access levels for configuring the device,

for the installer and for the administrator.

www.trikdis.com 5 November, 2018

GSM gate controller GV17

1.1 Specifications

Parameter Description

2G GSM modem frequencies 850 / 900 / 1800 / 1900 MHz

3G UMTS modem frequencies 800 / 850 / 900 / 1900 / 2100 MHz

Power supply voltage 9-32 V DC

12-24 V AC

Current consumption 100 mA

Inputs 2, selectable type: NC, NO, EOL=10 kΩ

Universal inputs/outputs 2, can be set either as input IN with type: NC, NO, EOL=10 kΩ, or

output OUT (open collector (OC) 50 mA)

Output 1, relay, 1 A 30 V DC, 0,5 A 125 V AC

Unsent events memory Up to 60 events

Event log memory Up to 5000 events

Users who receive messages

and have permission to control

Users who have permission to

control

990

Operating environment Temperature from –20 °C to +50 °C, relative humidity – up to 80%

at +20 °C

Dimensions 92 x 62 x 26 mm

Weight 80 g

1.2 Controller elements

1. Light indicators.

2. Frontal case opening slot.

3. USB Mini-B port for controller programming.

4. Terminal for external connections.

5. Nano-SIM card slot.

6. GSM antenna SMA connector.

www.trikdis.com 6 November, 2018

GSM gate controller GV17

1.3 Purpose of terminals

Terminal Description

AC/+DC Power terminal (9-32 V DC positive; 12-24 V AC)

AC/-DC Power terminal (9-32 V DC negative; 12-24 V AC)

1 IN 1st input, of selectable type NO, NC, EOL (factory setting: NO)

2 IN 2nd input, of selectable type NO, NC, EOL (factory setting: NO)

COM Common terminal

3 I/O Input/output (factory setting: type OC output)

4 I/O Input/output (factory setting: type OC output)

NC Relay terminal NC

C Relay terminal C

NO Relay terminal NO

A RS485 Contact A of RS485 bus

B RS485 Contact B of RS485 bus

1.4 LED indication of operation

Indicator Light status Description

NETWORK Green solid Connected to GSM network

Yellow blinking Indication of GSM signal strength from 0 to 5. Sufficient

strength is 3.

DATA Green solid Message is being sent

Yellow solid There are unsent event messages in the data buffer

POWER Green blinking The power supply voltage is sufficient

Yellow blinking The power supply voltage is insufficient

Red and yellow

blinking

Configuration mode is on

TROUBLE Off No operation problems

1 blink No SIM card inserted

2 blinks The PIN code of the SIM card is incorrect

3 blinks Unable to connect to GSM network

4 blinks Unable to connect to Protegus or to the primary IP receiver

5 blinks Unable to connect to the backup IP receiver

6 blinks Internal clock is not set

7 blinks The power supply voltage is insufficient

www.trikdis.com 7 November, 2018

GSM gate controller GV17

If the LED indication is not working, check the power supply and connections.

Note: Before beginning installation, make sure that you have the necessary components:

1) USB Mini-B type cable for configuration.

2) Cable consisting of at least 4 wires for connecting the controller.

3) Flat-head 2,5 mm screwdriver.

4) External GSM antenna if reception is weak in the area.

5) Activated nano-SIM card (can have turn off PIN code requests).

6) Instruction manual for the automatic gate to which the GSM gate controller is about

to be connected.

Order the necessary components separately from your local retailer.

1.5 GSM gate controller GV17 standard packing list

GSM gate controller GV17 1 pc.

GSM antenna 1 pc.

Resistor 10 kΩ 3 pcs.

Double-sided adhesive tape (5 cm) 1 pc.

Screw 2 pcs.

2 Wiring schematics for the GSM gate controller GV17

2.1 Fastening

1. Remove the top lid. Pull out the plug

part of the terminal block.

2. Remove the PCB board.

3. Fasten the base of the case in the

desired place using screws.

4. Reinsert the board and the terminal

block.

5. Screw the GSM antenna in.

6. Insert the nano-SIM card.

7. Close the top lid.

www.trikdis.com 8 November, 2018

GSM gate controller GV17

2.2 Schematic for connecting the power supply

Using wires, connect the GV17 controller according to the schematic shown below.

2.3 Schematics for connecting inputs

The GV17 has four inputs IN (two of which are universal and can operate either as inputs or outputs) for

the connection of various alarm sensors. These inputs can operate in NC, NO, EOL modes. Connect the

inputs according to the set input type (NC, NO, EOL) as is shown in the schematics bellow:

2.4 Schematic for connecting the relay

Above is the schematic for connecting the relay when the GV17 is connected to a DC power source. Using

the terminals of the relay, it is possible to remotely control (turn on/off) various electric devices.

www.trikdis.com 9 November, 2018

GSM gate controller GV17

3 Quick set up of the controller

Note: The controller comes factory pre-configured to work. A call from any phone to controller’s

SIM card number will turn on the 5 OUT relay output for 3 (three) seconds. The controller can

be installed without any additional configuration if such operation mode is acceptable.

1. A nano-SIM card must be inserted into the GV17. Turn off PIN code requests for the card before

inserting it into the controller.

2. Connect a power source to the GV17 (see 2 “Wiring schematics for the GSM gate controller GV17 ”).

3. Turn on the power for the controller. This should trigger the following GV17 LED indications:

 The “Power” indicator should blink green;

 The “Network” indicator should be green solid and blink yellow.

The default settings allow control by anyone who calls the phone number of the SIM card inserted into the

controller.

If you want to allow only particular people to control the controller, send an SMS command with user

phone numbers, who are authorized (example SMS command: SETU 123456 +370xxxxxxxx#Peter).

After receiving such command, GV17 will react only to the phone numbers on the list. The controller will

ignore incoming phone calls from other numbers.

Note: If you wish to alter the default settings or turn on other functions of the controller, refer to

chapter 5 „Setting of parameters using TrikdisConfig software“.

4 Remote control

4.1 Control with phone call

Call the number of the SIM card inserted into the controller. The controller automatically rejects the call

and turns on the 5 OUT relay output for 3 (three) seconds. Default settings allow anyone who calls the

number of the SIM card inserted into the controller to control.

4.2 Control with phone keyboard

GV17 answers and allows to control the outputs with a phone call the user is allowed to control several

outputs OUT:

1. Call the controller’s SIM card number. The controller will accept the call.

2. Using the phone keyboard, dial the control command (command examples can be found in the table

DTMF control commands).

Note: The first one to call (or send an SMS to) the controller will become the system administrator

and will be the only one who can administer and control the controller with SMS commands.

www.trikdis.com 10 November, 2018

GSM gate controller GV17

DTMF control commands

DTMF code Function Description

OUTPUT*STATE# Output

control

Output control command (turn on/turn off; turn on/turn off for

pulse time).

OUTPUT – number of the controlled output.

STATE – control command:

0 – turn off output;

1 – turn on output;

2 – turn off output for pulse time;

3 – turn on output for pulse time;

(output pulse time can be set using the TrikdisConfig program, in

the Input/Output settings table)

# - control command end symbol.

E.g. (turn on output 5): 5*1#

E.g. (turn on input 4 for pulse time): 4*3#

# Command

end symbol

If you made a mistake writing a command, dial # and enter the

control command again.

4.3 Control using Protegus cloud

With Protegus users will be able to control GV17 remotely. They will also be able to see the system state

and receive all system event messages.

1. Download and launch the Protegus app or use the browser version of Protegus at

www.protegus.eu/login.

2. Log in with your user name and password or register and create a new account.

3. Choose Add new system and enter the GV17 Unique ID (IMEI) number found on the product or on

the packaging sticker.

IMPORTANT:

When adding the GV17 to Protegus:

1. The Protegus service must be turned on. Turning on the service is described in

chapter 5.4 Window “IP reporting”;

2. The power supply must be turned on („POWER“ LED must blink green);

Otros manuales para GV17

Tabla de contenidos

Otros manuales de Controladores de Trikdis

Trikdis

Trikdis GV17 Manual de usuario

Trikdis

Trikdis GV15 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario