Trikdis GV15 Manual de usuario

Draugystės g. 17

LT-51229 Kaunas

E-mail [email protected]

www.trikdis.com

Controller GV15

This document describes controller GV15, its use, features, operation and setting of operation parameters.

Controller GV15 is a remote control device for electro-technical equipment (gate opening or rising, premises

heating or ventilation, lawn or greenhouse irrigation, pump, boiler, transporter and other system control).

Control commands are transmitted via GSM. After a call made to the number of the inserted SIM card, the

controller checks the caller number, under the set operation mode rejects the call and switches relay contacts.

There is a possibility to switch controller relay contacts using SMS message or DTMF commands.

SMS messages:

Sending SMS messages on entry events;

Entry event description by individual text;

Sending SMS confirmations on control

command execution;

Sending the comprehensive periodic test

message;

SMS message distribution to administrators

based on controller event types;

All operation parameter setting by SMS

messages;

SMS commands to receive the lists of

administrators and users;

Controller remote reset;

Unauthorized call and SMS denial

Key features:

2 Relays for equipment control;

2 inputs, e.g. for the circuit of mounting case

lock or gate limit sensor;

8 administrators and 1000 user names and

their phone numbers;

Import and export of user phone numbers and

user names;

Customising the preferred switching period of

relay contacts;

Comprehensive controller operation light

indication;

Exceptionally easy to install and run.

Three dial control operation modes:

All – controller relay contacts may be

switched by any caller;

Users and Administrators – controller relay

contacts may be switched by the caller,

whose phone number is either on the user or

administrator phone number list;

Administrators only – controller relay

contacts may be switched by the caller,

whose phone number is on the administrator

phone number list.

Controller GV15

Safety requirements

Get familiar with this manual prior to the controller usage.

Installation and maintenance of the controller shall be subject to qualified specialists having knowledge on GSM

equipment performance and relevant safety requirements.

External power supply during controller installation works must be switched off!

The controller shall be installed in the premises at restricted access zones and safe distance from sensitive electronic

devices. The controller is not resistant to vibration, other mechanical impact, moisture and aggressive chemical

environment. The controller complies with the requirements of Standard EN 50131 applied to environmental impact

resistance Class II.

Warranty and liability limitations

The product installed and operated in accordance with the interface user's manual and electrical equipment

installation procedure shall be provided with 24-months warranty by manufacturer. Warranty shall be effective as

of product purchase-sales transaction, i.e. invoice or cash receipt issue date.

Warranty may be terminated prematurely in the following cases:

The controller was repaired or attempted to repair by an unauthorized person;

The controller was used not for its intended purpose;

The controller was stored and/or installed in inadequate premises with inappropriate climate conditions,

aggressive chemical environment;

The controller was mechanically broken and/or deliberately damaged;

The controller damage was caused by force-majeure (lightning discharge etc.).

The manufacturer shall not be liable for the following:

The controller failures when controller is installed or used inconsistent with its user manual;

The controller failures if occurred due to disturbed, lost GSM/GPRS/Internet connection or any troubles in

operator's networks;

Termination or restriction of GSM/GPRS/Internet communication services to the controller buyer or

controller user, and shall not reimburse the controller buyer or controller user for property or non-property

losses incurred;

Termination or restriction of electrical power supply to the controller buyer or control panel user, and shall

not reimburse the controller buyer or control panel user for property or non-property losses incurred;

Controller GV15

Contents

1TECHNICAL PARAMETERS ............................................................................................................................ 5

2COMPONENT PARTS .................................................................................................................................. 5

3CONTROLLER COMPONENTS...................................................................................................................... 6

PURPOSE OF TERMINALS.......................................................................................................................................6

LIGHT INDICATION ...............................................................................................................................................7

4CONTROLLER INSTALLATION ...................................................................................................................... 8

INSTALLATION PROCEDURE....................................................................................................................................8

5WIRING DIAGRAMS ................................................................................................................................... 9

INPUTS CONNECTION ...........................................................................................................................................9

6CONTROLLER OPERATION AND CONFIGURATION WITH “TRIKDISCONFIG” .....................................................10

CONNECTION VIA USB CABLE TO TRIKDISCONFIG ...................................................................................................10

GENERAL SOFTWARE OPERATION .........................................................................................................................10

ACCESS PARAMETERS .........................................................................................................................................12

6.3.1 Changing Access and SMS password........................................................................................................12

6.3.2 Restore of default settings........................................................................................................................12

INPUT PARAMETERS...........................................................................................................................................13

6.4.1 Input type selection ..................................................................................................................................13

6.4.2 Message sending after actuation/restoration..........................................................................................13

RELAY PARAMETERS...........................................................................................................................................13

6.5.1 Operation modes ......................................................................................................................................13

6.5.2 Control types.............................................................................................................................................13

USER LIST PARAMETERS......................................................................................................................................14

6.6.1 User list importing/exporting ...................................................................................................................14

ADMINISTRATOR PARAMETERS ............................................................................................................................15

6.7.1 Message text parameters.........................................................................................................................16

PERIODICAL TEST MESSAGES................................................................................................................................16

CONTROLLER OPERATION FIRMWARE UPDATING.....................................................................................................17

7CONFIGURATION AND CONTROL BY SMS MESSAGES.....................................................................................17

ACCESS AND SMS PASSWORD RECOVERY ..............................................................................................................20

8CONTROLLER SMS MESSAGES ...................................................................................................................21

9AUTOMATICS CONTROL............................................................................................................................22

BY PHONE CALL.................................................................................................................................................22

BY DTMF TONE PHONE CALL ..............................................................................................................................22

BY SMS MESSAGE.............................................................................................................................................23

Controller GV15

Technical parameters

1Technical parameters

Parameter

Description

GSM modem frequencies

850 / 900 / 1800 / 1900 MHz

Power supply

12-36 V DC or 12-24 V AC

Current usage

Standby – 50 mA

While sending SMS – instantly up to 0,25 A

Number of relays

Relay commutated

DC or AC up to 24 V, current up to 1 A

Relay control command

By phone call, SMS or DTMF tones

Switching relay contacts

Pulse – control command commutates relays for 1-60 sec.

Level – control command commutates relays until the next control

command, e.g., until the next call.

Memory

Up to 8 administrator names and their phone numbers

Up to 1000 user names and their phone numbers

Inputs

2 (IN1 and IN2),

Set for NO (R ≥ 10 kΩ) or NC (R ≤ 0,5 kΩ)type circuits

Operating environment

Air temperature from -20 C to +50 C, at humidity up to 93%

(without condensation)

Parameter setting

a) Software "TrikdisConfig" via USB;

b) Special syntax SMS messages

Controller dimensions and

weight

100.6 x 80.7 x 23.5 mm , up to 110g

2Package contains

Controller GV15

1 pc.

Adhesive mounting tape (7cm)

1 pc.

GSM antenna ANT04 (2,5 m with

stick-on pad)

1 pc.

Note: USB cable (Mini-B type) designed for controller programming is not included.

Controller GV15

Controller components

3Controller components

Purpose of terminals

Name

Description

+/~ 12-24 V

Power supply + terminal or alternating supply voltage terminal

-/~ 12-24 V

Power supply - terminal or alternating supply voltage terminal

IN1

1st input IN1 terminal

COM

Common ground terminal for inputs IN1 and IN2

IN2

2nd input IN1 terminal

NO1

1st relay NO terminal

1st relay common terminal

NC1

1st relay NC terminal

NO2

2nd relay NO terminal

2nd relay common terminal

NC2

2nd relay NC terminal

4. SIM card slot

5. USB Mini-B connector for controller programming

1. GSM antenna SMA port

2. Light indicators

3. Removable external contact connector

Controller GV15

Controller components

Light indication

Indicator

Status

Description

Network

Off

Controller is turned off or GV15 initiation in

progress

Blinking

Registration to GSM network in progress

Lighting for 5 sec.

+ N flashes

N - relative GSM signal level

3 flashes – minimum sufficient level (30%),

10 flashes – maximum (100%)

Data

Off

No operations

Data processing (receiving a call or

receiving/sending SMS/programming in

progress)

Power

Off

Too low supply voltage or no power supply

Lighting

Normal power supply

Trouble

Off

Non troubles

Lighting for 5 sec.

+ N flashes:

1 flash

Insufficient supply voltage

2 flashes

No SIM card

3 flashes

PIN code error

4 flashes

Registration to GSM network within 60 seconds

failed

5 flashes

Operation mode setting error *

6 flashes

Threshold GSM signal level (~ 30%)**

7 flashes

Critical error in the parameters structure

8 flashes

Error in the user phone number list structure

Notes:

* - not a single administrator phone number is entered and the user list is prohibited.

** - use a portable GSM antenna with a cable and fit it to the exterior of the case if a controller is mounted into the

metal case of automatics.

Controller GV15

Controller installation

4Controller installation

Controller factory settings provide that any user calling to the number of the inserted SIM card can control the first

relay. The user of Administrator level can control both relays by sending a message of respective content. In order

to have dial control from authorized users or change factory settings, after installation procedure see 6 “Controller

operation and configuration with “TrikdisConfig”.

Opening of the controller case

Controller mounting dimensions

To open the case push pointed locations as shown on

a diagram and lift the case cover.

Dimensions are expressed in millimetres

Installation procedure

1) Open the controller case and insert the SIM card into the controller. SIM card must be already registered in

GSM network. Prior inserting the card, ensure that PIN code request function is disabled.

2) Embed the controller into the automatics mounting case.

3) Connect GSM antenna.

4) Connect controller power supply and automatics control circuits to the controller contacts according to the

scheme below.

5) Turn on power supply of the whole system.

6) Wait for the controller to start operating. Monitor the light indication of the controller operation:

Network LED lights up for 5 seconds and flashes at least 3 times;

Trouble LED does not light up;

Power LED lights up in green.

If the indication differs from the above listed, see 3.2 “Light indication".

7) Check if the automatics can be controlled by a call – call to the SIM card number of the controller.

8) Send these two SMS messages to the controller SIM card number in order to gain the administrator status

and change the default password of SMS commands:

"123456 SETAP APNR1:+NNNNNNNNNNN" (Administrator phone number adding command.

+NNNNNNNNNNN – administrator phone number).

"123456 PSW XXXXXX" (New SMS password setting command. Instead of XXXXXX enter your six digit

code and remember it).

If you wish your system to be controlled by authorized persons only, it must be configured using SMS messages or

software TrikdisConfig. For more details read sections 6 “Controller operation and configuration with “TrikdisConfig”

and 7 “Configuration and control by SMS messages“.

Controller GV15

Wiring diagrams

5Wiring diagrams

Inputs connection

The controller contains two input terminals (IN1 and IN2) for connection of sensor circuits. For setting the input

connection type and reports on activations see. 6.4 “Input “.

NC, Normally Closed

NO, Normally Open

Controller GV15

Controller operation and configuration with “TrikdisConfig”

6Controller operation and configuration with “TrikdisConfig”

Connection via USB cable to TrikdisConfig

1) Parameter setting software TrikdisConfig should be installed. Software available at www.trikdis.lt, page

about controller.

2) After the software is installed, connect the controller and computer with USB cable. Power supply via

USB port is sufficient to set the controller operation parameters, so additional supply is not necessary.

3) Run the parameter setting software "TrikdisConfig“.The firmware shall automatically recognize the

connected device and open a new window for programming.

General software operation

1) To read the parameters entered in the controller, click the button Read [F4] and enter Access and SMS

password in the pop-up window (Window requesting password will not appear if the password is set to

default). When the controller operation parameters are read for the first time, the software will show

default parameters.

2) After changing the parameters, click the button Write [F5] to enter the changes in the controller

memory.

3) The controller configuration may be saved in the computer. Click the button Save [F9] and create the

controller configuration file. When needed, open the file by clicking the button Open [F8].

4) When the configuration is complete, unplug the USB cable from the controller USB port. Disconnect

from the product in the software by clicking the button Logout.

Menu Main action buttons

Status bar

Tabla de contenidos

Otros manuales de Controladores de Trikdis

Trikdis

Trikdis GV17 Manual de usuario

Trikdis

Trikdis GV17 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario