TRENDnet TE-4010 Guía del usuario

The information contains in this file is a startup guide for using the

TE-4010 with TRENDnet-View ver. 1.1.

Before you begin, make sure you have the following described environment:

o A PC with a network card installed and properly configured (IRQ and I/O

base address are set). We use TE-16XP/CT, but you can use any NE-2000

compatible cards.

o Windows ver. 3.1 is properly installed on the PC's hard drive.

o The PC is physically connected through a RJ-45 cable with TE-4010. It does

not matter which port is connected to.

o No network software (or driver) is loaded in either CONFIG.SYS and

AUTOEXEC.BAT files. A "clean boot" is preferred.

o Need two pieces of 25-pin serial cable and make the connection from hub's

OUT-OF-BAND management port -> serial cable -> null modem (provided with

TE-4010) -> serial cable -> PC's com1 or com2 port.

1. Start Windows 3.1.

2. Run TERMINAL program in the ACCESSORIES Group.

3. Make sure you have the following configurations:

o Full duplex

o Asynchronous communication

o Data: 8 bit

o Stop bits: 1

o Parity: none

o Baud rate: 9600

o COM1 or COM2 port

4. Press enter several time to go into the setup menu described on page 25

of the TE-4010's manual. Do not type any password.

5. Record the Hub IP Address. For example, 192.132.65.36. You need the IP

address for the TRENDnet-View software. We will use this number for this

example setup procedure.

6. Exit the setup program by pressing ESC key.

7. Exit the TERMINAL program without saving the current configuration. You

are now ready to load TRENDnet-View software. You can disconnect the

serial cable and the null modem.

8. Load TRENDnet-View disk in the floppy disk drive.

9. From program manager, select Run... in the File menu. A dialog box

appears.

10. Type "A:INSTALL" (do not type " ") and click the OK button.

11. In the TRENDnet-View Configuration dialog box, modify the following

information where appropriate:

o IP Address: 192.132.65.xxx xxx, leave it at default

o Gateway IP Address: 192.132.65.xxx xxx, leave it at default

o Subnet Mask: 255.255.255.0

o Network card: NE-2000

o IRQ Number: xx xx, setting for the network card

o I/O Port: xx xx, setting for the network card

12. Type in your password for any future modification of the above settings.

Do not exit from Windows 3.1.

13. Load the TE-4010 SNMP Module disk in the floppy disk drive. The diskette

is included with TE-4010.

14. From program manager, select Run... in the File menu. A dialog box

appears.

15. Type "A:INSTALL" (do not type " ") and click the OK button.

16. The installation is automatic. All files will be copied to where

TRENDnet-View is installed.

17. Exit Windows to DOS prompt.

18. Change directory to where TRENDnet-View is installed. For example,

CD\TRENDNET.

19. Run MANAGER.BAT and it will bring up Windows 3.1 automatically.

20. Run TRENDnet-View by double clicking the TRENDnet-View In-band icon in

TRENDnet-View group.

21. You must place a TE-4010 software module in order for TE-4010 to be seen

by the TRENDnet-View software. Click once on the leftmost button in

the speed button bar. A Device window appears on the upper right corner

on the screen. Move the mouse over the TE-4010 icon and click on it to

select.

22. Move your mouse to the client area of the TRENDnet-View, notice your

mouse cursor changes from a pointer to a stamp. Click the mouse once and

a TE-4010 icon is placed on the client area area. Assign a name for this

hub and supply the IP Address for this hub (For example, 192.132.65.36).

Ignore all other entries. Close the dialog box.

23. Wait couple seconds and the hub's name (beneath the icon) will turn from

blue to green. Double-click the icon and you will see TE-4010 panel on

the screen. You are ready to manage your TE-4010!

Our current version of TRENDnet-View does not run with any network software

installed on the same machine. For example, Windows for Workgroups 3.1/3.11,

Novell Netware 2.x, 3.x, 4.x,....etc. Therefore, do not load any network

software (or network driver) before go into TRENDnet-View.

You must run MANAGER.BAT from DOS prompt before go into TRENDnet-View

software (in-band or out-of-band). MANAGER.BAT loads Windows 3.1

automatically.

Tabla de contenidos

Otros manuales de Enrutador de red de TRENDnet

TRENDnet

TRENDnet TE100-S5Pplus Guía de inicio rápido

TRENDnet

TRENDnet TE100S8P - Fast Ethernet Switch Manual de usuario

TRENDnet

TRENDnet TVP-224HR Guía del usuario

TRENDnet

TRENDnet TEW827DRUV2 Manual de usuario

TRENDnet

TRENDnet WRT-390L Manual de usuario

TRENDnet

TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M Manual de usuario

TRENDnet

TRENDnet TW100-BRV324 Manual de usuario

TRENDnet

TRENDnet TW100-BRV204 SHEETS Manual de usuario

TRENDnet

TRENDnet TWG-BRF114 Manual de usuario

TRENDnet

TRENDnet TPE-224WS - Web Smart PoE Switch Manual de usuario

TRENDnet

TRENDnet TW100-S4W1CA Manual de usuario

TRENDnet

TRENDnet TEG-S81g Manual de usuario

TRENDnet

TRENDnet TE100-S800i Manual de usuario

TRENDnet

TRENDnet TEG-448WS - Switch Manual de usuario

TRENDnet

TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M Manual de usuario

TRENDnet

TRENDnet TW100-BRM504 Manual de usuario

TRENDnet

TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M Manual de usuario

TRENDnet

TRENDnet TEW-721BRM Manual de usuario

TRENDnet

TRENDnet TW100-BRM504 Manual de usuario

TRENDnet

TRENDnet TDM-C400 Manual de usuario

TRENDnet

TRENDnet TEG -S81 g Manual de usuario

TRENDnet

TRENDnet TEW-652BRP Manual de usuario

TRENDnet

TRENDnet TW100-BRV304 SHEETS Manual de usuario

TRENDnet

TRENDnet TEW-721BRM Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad