Trek 2022 E-CALIBER Manual de funcionamiento

2022 E-CALIBER

SERVICE MANUAL SUPPLEMENT

2022 E-Caliber Service Manual

Contents

Safety 1

Headset with Knock Block 2

Frame and drive system guards 3

Rear triangle and chainstay bridge 4

Main pivot 6

Derailleur hanger 7

Cabling overview 8

IsoStrut remote lockout cable 9

IsoStrut 10

Air volume spacer 11

Carriage wiper seals and bushings 14

Fazua system 19

Specications 20

Suspension 21

Safety

WARNING

Alwaystightenhardwaretothespeciedtorque.

Over-tightening hardware could deform or break the

hardwareorcomponents.Under-tighteninghardware

couldcausehardwareorcomponentstobecomeloose.

Either situation could damage the bicycle and result in

injurytotherider.

WARNING

All reused-fasteners with pre-applied threadlocker must

be cleaned with isopropyl alcohol and have new thread-

lockerappliedbeforere-assembly.Ifthreadlockerisnot

applied, the fasteners may loosen which could damage

thebicycleandresultininjurytotherider.

2022 E-Caliber Service Manual

Headset with Knock Block

Item Description

Quantity in

Assembly Part Number Torque (Nm)

1 Upperbearingcover 1

5252159

—

2 Knock Block chip bolt 1 2

3 Knock Block chip, 62 degrees 1 —

4 Compression ring 1 —

5 Upperbearing 1 —

6 Lower bearing 1 5252158 —

7 Crown race 1 —

Tools

• 2.5mmhextool

• Torquewrenchwith2.5mmhexbit

• Headset tools

• Grease

1. Inspectthecomponentsfordamageorexcessive

wear.

• Knock Block chip (3)

• Undersidechanneloftheupperbearingcover(1)

• Interlocking keys of the upper bearing cover (1)

and the stem

2. Replaceanydamagedorworncomponents.

3. Apply grease to:

• Upperandlowerheadtubebearingbores.

• Inside of the bearing seats of the compression

ring(4)andthecrownrace(7).

4. Install the crown race (7), then the lower bearing (6)

ontothesteerertube.

5. Insert the steerer tube into the bottom of the head

tube.

6. Install the upper bearing (5), then the compression

ring(4)ontothesteerertube.

7. Insert the Knock Block chip (3) and bolt (2) into the

frame,butdonottightenit.

8. Installtheupperbearingcover(1).

9. Installspacersasneeded.

10. TorquetheKnockBlockchipbolt(2)to2Nm.

2022 E-Caliber Service Manual

Frame and drive system guards

Item Description

Quantity in

Assembly Part Number Torque (Nm)

1 Chainstay guard 1 W582883 —

2 Down tube guard 1 W582884 —

3 Drive unit guard fasteners 4 5269023 3

4 Drive unit guard 1 W1040440 —

Chainstay and down tube guards

Useisopropylalcoholtocleantheframesurfacewherethe

guardsattach.Waitforthealcoholtodrybeforeapplying

theguards.

Notice: Do not clean the entire frame with isopropyl

alcohol.Isopropylalcoholcoulddamagethepaint.

2022 E-Caliber Service Manual

Rear triangle and chainstay bridge

Item Description

Quantity in

Assembly Part Number Torque (Nm)

1 RearIsoStrutaxle 1 591626 10

2 End cap bolt 1 —

3 Front IsoStrut bolt and washer 2 W584485 5

4 Chainstay bridge bolt 4 5265697 8

5 Chainstay bridge, charcoal color 1 5266755 —

Tools

• Bike repair stand

• Torquewrenchwith6mmhexbit,T25andT30

Torxbits

• Grease

Important: You must have the main pivot bearing and

sleeve (See the Main pivot section on page 6) and the

IsoStrut (See the IsoStrut section on page 10) installed

on the rear triangle before attaching the rear triangle to

theframe.

1. Puttheseatpostinabikerepairstand.

2. Fitthereartriangleintothemainframe.

3. InstallthetwofrontIsoStrutboltsandwashers(3).

Important: Donottorquetheboltsatthistime.

4. Apply greasetotheIsoStrutrearaxle(1).

5. InstalltheIsoStrutrearaxle(1)andendcapbolt(2).

Important: Donottorquetheboltsatthistime.

6. Applygreasetotheatsurfacesofthechainstay

bridge(5).

2022 E-Caliber Service Manual

Rear triangle and chainstay bridge (continued)

7. Insert the chainstay bridge (5) inside the rear

triangle.

8. Install the four bridge bolts (4) to attach the bridge to

thereartriangle.

9. If applicable, install the main pivot hardware before

torquingthebridgebolts(4).SeetheMain pivot

section on page 6.

10. Torque:

• Chainstaybridgebolts(4)to8Nm.

• IsoStrutrearaxle(1)to10Nm.

• FrontIsoStrutbolts(3)to5Nm.

2022 E-Caliber Service Manual

Main pivot

234

Item Description Quantity in

Assembly

Part Number Torque (Nm)

1 Main pivot nut 1 W584134 —

2 Washer 2 W440921 —

3 Main pivot bearing 2 W302025 —

4 Main pivot sleeve 1 W600642 —

5 Main pivot bolt 1 W600628 30

Tools

• Bearing press

• 8mmhextool

• Torquewrenchwith8mmhexbit

• Grease

1. Pressinthedrivesidebearing(3).

2. Insertthesleeve(4)fromthenon-driveside.

3. Press-inthenon-drivesidebearing(3).

4. Position the chainstay over the seat tube, making

surethemainpivotholesarealigned.

Tip: Slidethelongarmofthehextoolfromthenon-

drivesideandthroughthealignedpivotholes.For

eachstep,slidethecomponentontothehextoolto

alignthecomponentsoneachsideofthemainpivot.

5. Apply grease to the shoulder of the main pivot

bolt(5).

6. Insert the driveside washer (2) between the bearing

thechainstay.

7. Partially insert the main pivot bolt (5) from the drive

side.

8. Insert the non-driveside washer (2) bewtween the

bearingthechainstay.

9. Fullyinsertthemainpivotbolt(5).

10. Installthenut(1).

11. Torquethemainpivotbolt(5)to30Nm.

2022 E-Caliber Service Manual

Derailleur hanger

Item Description Quantity in

Assembly

Part Number Torque (Nm)

1 Thruaxle,M12X1.0X15MM 1 W600321 10

2 Derailleur hanger 1

W600660

—

Hanger bolt, left-handed thread 1 25

Washer, 25mm 1 —

ThisbicycleframeisdesignedtouseaUniversalDerailleur

Hanger(UDH).

NOTICE: ThethruaxlemustbecompatiblewithaUDH

andmustbeM12x1.0witha12.7mmthread.

NOTICE: Thewasherisframe-specic.Installonlythe

washercompatiblewithyourframe.

WARNING

Donotapplygreasetothederailleurhangerorbolt.

Applygreasetoonlythethruaxle.

1. Insert the hanger on the inside of the driveside

chainstay.

2. Installthewasheronthederailleurhangerbolt.

3. Inserttheboltintotheframe.

4. Makesurethehangerispositionedasshownbelow.

5. Torquethehangerboltto25Nm.

NOTICE: Donotover-tighten.Over-tighteningthebolt

couldcausethehangertobreak.

ForadditionalinformationabouttheUDH,refertothe

SRAM user manual at sram.com.

2022 E-Caliber Service Manual

Cabling overview



Item Description Quantity in

Assembly

Part Number Torque (Nm)

1 Bolt 1 W562831 3

2 Speed sensor 1 W581396 —

3 Rear brake cable 1 — —

4 Speed sensor cable 1 — —

5 Dropper post cable 1 — —

6 IsoStrut lockout cable 1 — —

7 Head tube cable guide 2 W519232 —

8 Head tube cable guide fastener 2 W532763 1

9 Controller cable 1 — —

10 Down tube cable guide 3 W591416 —

11 Rear derailleur cable 1 — —

12 Grommet, for use with wireless derailleur only 1 5259425 —

Zip tie location 4 — —

Routeandziptiethecablesasshownintheillustrationabove.

Dropper cable

• For detailed dropper remote instructions, please refer

to the Drop Lock Remote manual at trekbikes.com/

manuals.

IsoStrut cable

• See the IsoStrut remote lockout cable section on

page 9.

2022 E-Caliber Service Manual

IsoStrut remote lockout cable

Tools

• Cable cutter

• Torquewrenchwith2mmhexbit

1. Installthecableintheremotelockout.

2. Route the cable through the hole in the bottom of the

top tube just forward of the IsoStrut and out the drive

sideoftheheadtubehole.

3. Attheheadtube,routethewirethroughthecable.

4. AttheIsoStrut,slidetheferruleonthewire.

5. Guidethewirethroughtheslotinthecablestop.

6. Route the wire around the lockout spool and install

thesetscrew.Torqueto1Nm.

Drive side Non-driveside

7. Testthatthemechanismworkssatisfactorily.

8. Cut the wire to the appropriate length (20-30mm)

andcrimpanendcaponit.

Tabla de contenidos

Otros manuales de Bicicleta de Trek

Trek

Trek MADONE SL 2022 Manual de funcionamiento

Trek

Trek Rail 9.5 Gen 4 Manual de usuario

Trek

Trek Bicycle Computer Manual de usuario

Trek

Trek DOMANE AL GEN 4 2024 Manual de usuario

Trek

Trek DOMANE SL 2023 Manual de usuario

Trek

Trek Lync Manual del propietario

Trek

Trek 2022 CHECKPOINT SL Manual de funcionamiento

Trek

Trek FUEL EXE 2023 Manual de usuario

Trek

Trek Farley Carbon 9.6 2023 Manual de usuario

Trek

Trek Kickster 2019 Manual de usuario

Trek

Trek DOMANE SLR 2017 Manual de usuario

Trek

Trek Powerfly Gen 3 FS 9 EQ Manual de usuario

Trek

Trek ALLOY FUEL EXE Manual de usuario

Trek

Trek Madone 2016 Manual de usuario

Trek

Trek Domanee 2017 Manual de usuario

Trek

Trek Farley 5 Manual de usuario

Trek

Trek HYENA Manual de usuario

Trek

Trek Powerfly HT Sport EQ 4 Manual de usuario

Trek

Trek MARLIN 6 Manual de usuario

Trek

Trek Domane SL Manual de usuario

Trek

Trek Bicycle Computer Manual de usuario

Trek

Trek RIDE+ Manual de usuario

Trek

Trek Fetch+ 4 Manual de usuario

Trek

Trek Sport EQ 4 Manual de usuario

Manuales populares de Bicicleta de otras marcas

RAMBO

RAMBO R1000X2M-FF-BFD Manual de usuario

Vermeiren

Vermeiren SAFARI Manual de usuario

Velec

Velec A2/36V Manual de usuario

Coswheel

Coswheel A-ONE Manual de usuario

Betzold

Betzold 97869 Manual de usuario

Cervélo

Cervélo S3 2019 Manual de usuario

Tenways

Tenways AGO X Manual de usuario

Festo

Festo EGSC-BS-KF Manual de lista de piezas

Gio Electric

Gio Electric H1 Volt Manual de usuario

GOGOBEST

GOGOBEST GM30 Manual de usuario

DAHON

DAHON CIAO - 2009 Manual de usuario

Aprimatic

Aprimatic ONDA 500 Guía de inicio rápido

MV Agusta

MV Agusta Lucky Explorer GRAVEL Manual de instrucciones

Greyp

Greyp G6 Series Manual de usuario

Babboe

Babboe Carve-E Manual de usuario

Huka

Huka orthros Manual de usuario

Xtracycle

Xtracycle Stoker 2021 Manual de usuario

APRILIA

APRILIA DORSODURO 750 ABS 2015 Manual de usuario