Transition Networks SBFTF10XX-15X Manual de usuario

User’s Guide

SBFTF10xx-15x

Stand-Alone Media Converter

• Copper to Fiber

• 10/100 Bridging (2-Port)

• 10Base-T/100Base-TX to 100Base-FX

The SBFTF10xx-15x 2-port Ethernet/Fast Ethernet

bridging media converter connects 10Base-T

Ethernet or 100Base-TX Fast Ethernet twisted-pair

copper network devices to network devices on a

100Base-FX Fast Ethernet fiber network.

SBFTF1029-150** RJ-45

100 m (328 ft)*

SC, 1310 mn (TX)/1550 nm (RX)

single mode, 20 km (12.4 miles)*

SBFTF1029-151** RJ-45

100 m (328 ft)*

SC, 1550 mn (TX)/1310 nm (RX)

single mode, 20 km (12.4 miles)*

SBFTF1029-152*** RJ-45

100 m (328 ft)*

SC, 1310 mn (TX)/1550 nm (RX)

single mode, 40 km (24.8 miles)*

SBFTF1029-153*** RJ-45

100 m (328 ft)*

SC, 1550 mn (TX)/1310 nm (RX)

single mode, 40 km (24.8 miles)*

Part Number Port One - Copper

10Base-T/100Base-TX

Port Two - Duplex Fiber-Optic

100Base-FX

SBFTF1011-150 RJ-45

100 m (328 ft)*

ST, 1300 nm multimode

2 km (1.2 miles)*

SBFTF1013-150 RJ-45

100 m (328 ft)*

SC, 1300 nm multimode

2 km (1.2 miles)*

SBFTF1014-150 RJ-45

100 m (328 ft)*

SC, 1310 nm single mode

20 km (12.4 miles)*

SBFTF1015-150 RJ-45

100 m (328 ft)*

SC, 1310 nm single mode

40 km (24.8 miles)*

SBFTF1018-150 RJ-45

100 m (328 ft)*

MT-RJ, 1300 nm multimode

2 km (1.2 miles)*

* Typical maximum cable distance. Actual distance is dependent upon the

physical characteristics of the network. (TX) = transmit (RX) = receive

** SBFTF1029-150 and SBFTF1029-151 are intended to be installed in the same

network where one is the local converter and the other is the remote

converter.

*** SBFTF1029-152 and SBFTF1029-153

are intended to be installed in the

same network where one is the local

converter and the other is the remote

converter.

Installation . . . . . . . . . . . . . . . . . .2

Operation . . . . . . . . . . . . . . . . . . .5

Cable Specifications . . . . . . . . . . .7

Technical Specifications . . . . . . . .9

Troubleshooting . . . . . . . . . . . . .10

Compliance Information . . . . . . .12

SBFTF10xx-15x

24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Installation

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when setting the 4-position switch. Failure to observe this caution

could result in damage to, and subsequent failure of, the media converter.

Set the 4-Position Switch

• The 4-position switch is located

on the side of the media

converter.

• Use a small flat-blade screwdriver

or a similar device to set the

recessed switches.

• Refer to the drawing for the

locations of the four individual

switches.

1. Auto-Negotiation

Up Enables Auto-Negotiation on the copper port.

Advertises 100 Mb/s full-duplex and half duplex,

and 10 Mb/s full-duplex and half duplex.

Down Disables Auto-Negotiation on the copper port.

2. Copper Mode

(Applies only if switch 1 is down.)

Up Forces full-duplex operation on the copper port.

Down Forces half-duplex operation on the copper port.

3. Speed

(Applies only if switch 1 is down.)

Up Forces 100 Mb/s operation on the copper port.

Down Forces 10 Mb/s operation on the copper port.

4. Fiber Mode

Up Forces full-duplex operation on the fiber port.

Down Forces half-duplex operation on the fiber port.

Speed (up=100Mb/s)

Copper Mode (up=Full-Duplex)

Auto-Negotiation (up=Enabled)

Fiber Mode

(up=Full-Duplex)

1234

[email protected] -- Click the “Transition Now” link for a live Web chat. 3

Installation -- Continued

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when setting the jumper. Failure to observe this caution could

result in damage to, and subsequent failure of, the media converter.

Set the Jumper

The Far-End Fault jumper is labeled “FE” for enable

Far-End Fault and “FD” for disable Far-End Fault (see

page 6).

Enable A fault on the fiber link causes the media

converter to transmit a Far-End Fault signal.

Disable No Far-End Fault signal is transmitted when

a fault occurs.

To set the jumper:

1. Using a small screwdriver, remove the four (4) screws that secure the

cover and carefully remove the cover from the media converter.

2. Locate the jumper on the circuit board labeled “FE” and “FD”.

3. Using small needle-nosed pliers or similar device, move the jumper to

the desired position. (Refer to the drawings above.)

4. Carefully replace the cover on the media converter and replace the four

(4) screws that secure the cover to the media converter.

Disable Far-End Faul

Enable Far-End Fault

FE FD

RJ-45 port

on the other device

(switch, work station, etc.)

RJ-45 port

on the media

converter

SBFTF10xx-15x

24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Install the Twisted-Pair Copper Cable

1. Locate or build 10Base-T or 100Base-TX copper cables with male, RJ-45

connectors installed at both ends.

2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port

connector on the media converter.

3. Connect the RJ-45 connector at the other end of the cable to the RJ-45

port connector on the other device (switch, workstation, etc.).

NOTE: The MDI (straight-through) or MDI-X (crossover) cable connection is

configured automatically, according to the network conditions.

Installation -- Continued

Install the Fiber Cable

1. Locate or build 100Base-FX fiber cable with male, two-stranded TX to RX

connectors installed at both ends.

2. Connect the fiber cables to the media converter as described:

• Connect the male TX cable connector to the female TX connector.

• Connect the male RX cable connector to the female RX connector.

3. Connect the fiber cables to the other device (another media converter,

hub, etc.) as described:

• Connect the male TX cable connector to the female RX connector.

• Connect the male RX cable connector to the female TX connector.

Connect the fiber cable

to the media converter

as shown.

Connect the fiber cable

to the other device

(media converter,

hub, etc.) as shown

[email protected] -- Click the “Transition Now” link for a live Web chat. 5

Operation

Power the Media Converter

1. Connect the barrel connector on the power adapter to the media

converter’s power port (located on the back of the media converter).

2. Connect the power adapter plug to AC power.

3. Verify that the media converter is powered by observing the illuminated

LED power indicator light.

For DC power, consult the user’s guide for the Transition Networks SPS1872-

xx DC external power supply for powering the media converter.

NOTE: The external power supply provided with this product is UL listed by

the power supply’s manufacturer.

Status LEDs

Use the status LEDs to monitor the media converter and the network

connections.

PWR (Power)

On = Connection to external AC or DC power.

FLNK (Fiber Link)

On = Fiber link connection.

Flashing = Fiber network activity.

FDPX (Fiber Duplex)

On = Full-duplex fiber connection.

Off = Half-duplex fiber connection.

TLKN (Twisted-Pair Link)

On = Copper link connection.

Flashing = Copper network activity.

TDPX (Twisted-Pair Duplex)

On = Full-duplex copper connection.

Off = Half-duplex copper connection.

TSPD (Twisted-Pair Speed)

On = 100 Mb/s.

Off = 10 Mb/s.

PWR

10/100Base-TX

100Base-FX

FDPX

FLNK

TLNK

TSPD

TDPX

SBFTF10xx-15x

24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Operation - Continued

Product Features

Auto-Negotiation

The Auto-Negotiation feature allows the media converter to automatically

configure itself to achieve the best possible mode of operation over a link.

The media converter broadcasts its speed (10 Mb/s or 100 Mb/s) and duplex

capabilities (full or half) to the other devices and negotiates the best mode of

operation. Auto-Negotiation allows quick and easy installation because the

optimal link is established automatically. No user intervention is required to

determine the best mode of operation.

A scenario where the media converter is linked to a non-negotiating device is

a case where the user may want to disable Auto-Negotiation. In this instance,

the mode of operation will drop to the least common denominator between

the two devices (e.g. 10 Mb/s, half-duplex). Disabling this feature gives the

user the ability to force the connection to the desired speed and duplex mode

of operation.

AutoCross™

When the AutoCross feature is activated, it allows either straight-through

(MDI) or crossover (MDI-X) copper cables to be used when connecting to

10Base-T or 100Base-TX devices. AutoCross determines the characteristics of

the connection and automatically configures the unit to link up, regardless if

the copper cable is MDI or MDI-X configuration. (This feature does not

require operator intervention.)

Far-End Fault

When a fault occurs on an incoming fiber link (1), the media converter

transmits a Far-End Fault signal on the outgoing fiber link (2). In addition the

Far-End Fault signal also activates the Link Pass-Through feature, which, in

turn, disables the link on the copper portion of the network (3) and (4).

Far-End Fault

nal is sent

Media

Converter A

Media

Converter B

Near-End

Device

Far-End

Device

original fault

on the fiber link

media converter B

disables the co

er lin

media converter A

disables the co

er link

[email protected] -- Click the “Transition Now” link for a live Web chat. 7

Operation - Continued

Product Features - Continued

Full-Duplex Network

In a full-duplex network, maximum cable lengths are determined by the type

of cables that are used. See page 1 (front cover) for the cable specifications

for the different SBFTF10xx-15x models.

The 512-Bit Rule does not apply in a full-duplex network.

Half-Duplex Network (512-Bit Rule)

In a half-duplex network, the maximum cable lengths are determined by the

round trip delay limitations of each Fast Ethernet collision domain. (A

collision domain is the longest path between any two terminal devices, e.g. a

terminal, switch, or router.)

The 512-Bit Rule determines the maximum length of cable permitted by

calculating the round-trip delay in bit-times (BT) of a particular collision

domain. If the result is less than or equal to 512 BT, the path is good.

For more information on the 512-Bit Rule, see the white paper titled “Collision

Domains” on the Transition Networks website at: www.transition.com.

Cable Specifications

Copper Cable Maximum cable distance: 100 meters

Category 3: (minimum requirement for 10 Mb/s operation)

Gauge 24 to 22 AWG

Attenuation 11.5 dB/100m @ 5-10 MHz

Category 5: (minimum requirement for 100 Mb/s operation)

Gauge 24 to 22 AWG

Attenuation 22.0 dB /100m @ 100 MHz

• Straight-through(MDI) or crossover (MDI-X) cable may be used.

• Shielded (STP) or unshielded twisted-pair (UTP) may be used.

• Pins 1&2 and 3&6 are the two active pairs in an Ethernet network .

• Use only dedicated wire pairs for the active pins:

(e.g., blue/white & white/blue, orange/white & white/orange, etc.)

• Do not use flat or silver satin wire.

Crossover Cable

Straight-Through Cable

Twisted Pair #1

Twisted Pair #2

SBFTF10xx-15x

24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Cable Specifications

The physical characteristics must meet or exceed IEEE 802.3™ specifications.

Fiber Cable

Bit Error Rate: <10-9

Single mode fiber (recommended): 9 µm

Multimode fiber (recommended): 62.5/125 µm

Multimode fiber (optional): 100/140, 85/140, 50/125 µm

SBFTF1011-150

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

SBFTF1013-150

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

SBFTF1014-150

Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber-optic Receiver Sensitivity: min: -31.0 dBm max: -8.0 dBm

Link Budget: 16.0 dB

SBFTF1015-150

Fiber-optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 26.0 dB

SBFTF1018-150

Fiber-optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber-optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

SBFTF1029-150, SBFTF1029-151

Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

SBFTF1029-152, SBFTF1029-153

Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm

Link Budget: 25.0 dB

The fiber optic transmitters on this device meet Class I Laser safety

requirements per IEC-825/CDRH standards and comply with 21

CFR1040.10 and 21CFR1040.11.

[email protected] -- Click the “Transition Now” link for a live Web chat. 9

Technical Specifications

For use with Transition Networks Model SBFTF10xx-15x or equivalent.

Standards IEEE 802.3™

Data Rate: 10 Mb/s, 100 Mb/s

Dimensions 3.25" x 4.7" x 1" (86 mm x 119 mm x 22 mm)

Weight 10 oz. (283 g) (approximate)

Power Consumption: 4.0 W

Power Supply 12VDC, 0.8 A (N. America, Europe, Japan, UK)

12VDC, 1.25 A (N.Z., Australia, Latin Am., S. Africa)

The external power supply provided with this product

is UL listed by the power supply’s manufacturer.

Packet Size: Unicast MAC addresses: 1K

Maximum packet size: 1522 bytes

Memory: 128K bytes (1 Mbit)

MTBF 48,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)

129,000 hours (Bellcore7 V5.0)

Environment Tmra*: 0 to 50°C (32 to 122°F )

Storage Temp: -20 to 85°C (-4 to 185°F )

Humidity 5 to 95%, non condensing

Altitude 0 to 10,000 feet

Warranty Lifetime

*Manufacturer’s rated ambient temperature.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,

Subchapter J applicable at the date of manufacture.

CAUTION: Visible and invisible laser radiation when open. Do not stare into

the beam or view directly with optical instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other

than those specified herein may result in hazardous radiation exposure.

Optional Accessories (sold separately)

Part Number Description

SPS-1872-SA Optional External Power Supply; 18-72VDC Stand-Alone

Output: 12.6VDC, 1.0 A

SPS-1872-PS Optional External Power Supply; 18-72VDC Piggy-back;

Output: 12.6VDC, 1.0 A

E-MCR-04 12-Slot Media Converter Rack w/ universal internal power supply

WMBL Optional Wall Mount Brackets; Length: 4.0 in. (102 mm)

WMBV Optional Vertical Mount Bracket; Length: 5.0 in. (127 mm)

WMBD Optional DIN Rail Mount Bracket; Length: 5.0 in. (127 mm)

WMBD-F Optional DIN Rail Mount Bracket (flat); Length: 3.3in. (84 mm)

SBFTF10xx-15x

24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Troubleshooting

If the media converter fails, isolate and correct the failure by determining the

answers to the following questions and then taking the indicated action:

1. Is the PWR (power) LED illuminated?

• Is the power adapter the proper type of voltage and cycle frequency

for the AC outlet? (See “Power Supply” on page 9.)

• Is the power adapter properly installed in the media converter and in

the outlet?

• Contact Technical Support: US/Canada: 1-800-260-1312,

International: 00-1-952-941-7600.

YES

• Proceed to step 2.

2. Is the TLNK (twisted-pair link) LED illuminated?

• Check the copper cables for proper connection and pin assignment.

• Contact Technical Support: US/Canada: 1-800-260-1312,

International: 00-1-952-941-7600.

YES

• Proceed to step 3.

3. Is the FLNK (fiber-pair link) LED illuminated?

• Check the fiber cables for proper connection.

• Verify that the TX and RX cables are connected to the RX and TX

ports, respectively, on the 100Base-FX device.

• Contact Technical Support: US/Canada: 1-800-260-1312,

International: 00-1-952-941-7600.

YES

• Proceed to step 4.

4. Is the TSPD (twisted-pair speed) LED illuminated?

• Check the copper cables for proper connection.

• Off = The media converter has selected 10Mb/s operation.

• If the speed is not correct, disconnect and reconnect the twisted pair

cable to restart the initialization process.

• Contact Technical Support: US/Canada: 1-800-260-1312,

International: 00-1-952-941-7600.

YES

• On = The media converter has selected 100Mb/s operation.

• If the speed is not correct, disconnect and reconnect the twisted pair

cable to restart the initialization process.

• Contact Technical Support: US/Canada: 1-800-260-1312,

International: 00-1-952-941-7600.

[email protected] -- Click the “Transition Now” link for a live Web chat. 11

Technical Support

Technical support is available 24 hours a day.

US and Canada: 1-800-260-1312

International: 00-1-952-941-7600

Transition Now

Chat live via the Web with Transition Networks Technical Support.

Log onto www.transition.com and click the Transition Now link.

Web-Based Seminars

Transition Networks provides seminars via live web-based training.

Log onto www.transition.com and click the Learning Center link.

E-Mail

Ask a question anytime by sending an e-mail to our technical support staff.

[email protected]

Address

Transition Networks

6475 City West Parkway, Minneapolis, MN 55344, USA

telephone: 952-941-7600, toll free: 800-526-9267, fax: 952-941-2322

Declaration of Conformity

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 USA

Model: SBFTF10xx-15x Series Media Converters

Part Number(s): SBFTF1011-150, SBFTF1013-150, SBFTF1014-150, SBFTF1015-150,

SBFTF1018-150, SBFTF1029-150, SBFTF1029-151, SBFTF1029-152,

SBFTF1029-153

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the

SBFTF10xx-15x

to which this declaration refers is

in conformity with the following standards.

EMC-CISPR 22:1985 Class A; EN 55022:1988 Class A; FCC Part 15 subpart B;

22 CFR subpart J

I, the undersigned, hereby declare that the equipment specified above conforms to the above

Directive(s) and Standard(s).

_August 8, 2002_____

Stephen Anderson, Vice-President of Engineering Date

Trademark Notice

All trademarks and registered trademarks are the property of their respective owners.

means - graphic, electronic, or mechanical - without written permission from Transition

Networks.

Printed in the U.S.A. 33227.D

Compliance Information

CISPR22/EN55022 Class A

CE Mark

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference, in which case the user will be required to correct the

interference at the user's own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus

set out on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la class A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

European Regulations

Warning This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können

bei Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für

Gegenmaßnahmen verantwortlich.

Attention! Ceci est un produit de Classe A. Dans un environment domestique, ce produit

risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de

prende les measures spécifiques appropriées.

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-

Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der

Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über

Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer

Konformität.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Transition Networks

Transition Networks

Transition Networks CSDTF3011-110 Manual de usuario

Transition Networks

Transition Networks SISTF1011-110-LR Manual de usuario

Transition Networks

Transition Networks C/E-TX-SX-02 Manual de usuario

Transition Networks

Transition Networks SRS2F3111-100 Manual de usuario

Transition Networks

Transition Networks Stand-Alone Media Converter S4TEF10xx-11x Manual de usuario

Transition Networks

Transition Networks SBFTF10xx-1xx Manual de usuario

Transition Networks

Transition Networks SAPTF33xx-100 Manual de usuario

Transition Networks

Transition Networks RS232-CF-01 Manual de usuario

Transition Networks

Transition Networks CPSVT26XX Manual de usuario

Transition Networks

Transition Networks M/E-PSW-FX-01SC Manual de usuario

Transition Networks

Transition Networks M/GE-ISW-SFP-01-PD Manual de usuario

Transition Networks

Transition Networks SBFTF10XX-10X Manual de usuario

Transition Networks

Transition Networks CFETF1011-105 Manual de usuario

Transition Networks

Transition Networks E-100BTX-FX-05 Manual de usuario

Transition Networks

Transition Networks SGFEB10 Series Manual de usuario

Transition Networks

Transition Networks SRS4F3111-100 Manual de usuario

Transition Networks

Transition Networks HSTR-CF-01(SC) Manual de usuario

Transition Networks

Transition Networks F-SM-MM-05 Manual de usuario

Transition Networks

Transition Networks E-100BTX-FX-05(LC) Manual de usuario

Transition Networks

Transition Networks SFMFF4040-100 Manual de usuario

Transition Networks

Transition Networks CBFTF1011-100 Manual de usuario

Transition Networks

Transition Networks SCSCF3011-100 Manual de usuario

Transition Networks

Transition Networks F-xM-MM-05 Manual de usuario

Transition Networks

Transition Networks CRMFE1011-200 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario