Transition Networks E-MCR-02 Manual de usuario

MEDIA CONVERTER RACK

TECHNICAL SPECIFICATIONS

Case dimensions 17.0" x 13.0" x 4.5" (432mm x 330mm x 114mm)

Power Requirements NOTE: Ensure that available power circuits are not overloaded.

Ensure that rack mounting equipment is reliably grounded.

Input Voltage 85-264 VAC

Input Frequency 47-63 Hz

Output Voltage 9 VDC

Output Current 600mA per port maximum

Power Cord TN P/N Requirement Location

3344 120 volts, 60 Hz USA/Canada

3344 100 volts, 50-60 Hz Japan

3347 230 volts, 50 Hz Europe

3348 240 volts, 50 Hz Australia

3349 240 volts, 50 Hz United Kingdom

Environment Temperature: 0-50°C (32° to 122° F )

Humidity 10-90%, non condensing

Altitude 0-10,000 feet

Warranty Lifetime

The Transition Networks Media Converter Rack provides space and power

in a rack-mountable chassis for twelve (12) separate and independent

Transition Networks media converters, each with power requirements

ranging from 9VDC to 12VDC.

The Media Converter Rack is designed ONLY for installation of media

converters designed and built by Transition Networks that have both

media input connector and media output connector located on the same

side of the media converter, opposite the power input connector.

The Transition Networks Media Converter Rack is shipped with attached

feet for installation on any well-ventilated table-top or shelf. Optionally,

the Media Converter Rack can be installed in a standard 19-inch rack,

using installation brackets and attachment screws provided.

Media Converter Rack

E-MCR-02

USER’S GUIDE

Compliance Information

Safety: UL 1950 and EN60950

C-UL Listed (Canada)

Emissions: FCC Class A, CISPR 22 Class A, EN55022

Immunity: EN50082, IEC 801-2,3,4

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to

part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the

radio interference regulations of the Canadian Department of Communications.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

any form or by any means – graphic, electronic, or mechanical – without written permission from

TRANSITION Networks.

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners. 33107.B

Minneapolis, MN 55344 USA

INSTALLATION

WARNING: Carefully mount the Media Converter Rack in a standard 19-inch

rack to prevent creating a hazardous condition due to uneven mechanical

loading. Failure to observe this warning could allow the Media Converter

Rack to fall, resulting in injury to personnel and/or equipment damage.

CAUTION: Do not use the Media Converter Rack chassis to provide earth

ground for any 10BASE-2 cable shield connected to any installed media con-

verter. Failure to observe this caution could cause the Media Converter Rack

and all installed media converters to fail.

Optionally Install E-MCR-02 in 19-inch Site Rack

NOTE: Mounting brackets provide two (2) sets of mounting holes, located

one inch apart, that allow site-selection of flush or recessed installation.

1 Attach mounting brackets to E-MCR-02:

• Locate two (2) mounting brackets and four (4) screws (PROVIDED) for

each Media Converter Rack to be installed.

• Align each mounting bracket

against side of Media Converter

Rack so that selected Media

Converter Rack installation

holes are visible through

mounting bracket installa-

tion holes and so that

bracket surface to be

attached to 19-inch site

rack is flush with front of

Media Converter Rack.

• Using Phillips screwdriver,

install two (2) screws through

each mounting bracket into side

of Media Converter Rack.

Attach E-MCR-02 to 19-inch site rack:

• Locate four (4) screws and optional clip-nuts (NOT PROVIDED) for each

Media Converter Rack to be installed.

• Carefully align the Media Converter Rack at a level position between the

19-inch site rack mounting rails.

• Install two (2) screws through right front bracket into right site rack

mounting rail and two (2) screws through left front bracket into left site

rack mounting rail, using clip nuts to secure if necessary.

2 Install Media Converter(s) in E-MCR-02

• Align media converter within installation space at front of Media

Converter Rack and carefully slide into place.

• Tighten thumb screw located on Media Converter Rack directly above

media converter to secure.

3 Install Media Cables at Front of Media Converter(s)

• Refer to documentation that comes with media converter(s) to determine

correct cable specifications and distances for each media converter.

• Connect input and output media cable at front of media converter(s).

4 Connect Media Converter(s) to Power

• Locate media converter power cord (shipped with connector secured in

rubber grommet located above media converter installation slot).

• Remove media converter power connector from rubber grommet and

install in power receptacle at back of media converter.

5 Power the Media Converter Rack

NOTE: Ensure that available power circuits are not overloaded and that rack

mounting equipment is reliably grounded.

• Locate power receptacle, associat-

ed fuse and power switch on

power supply at Media

Converter Rack back.

• Referring to power cord

specifications on back

page, verify that fuse is

installed at correct setting

for site installation. If not:

Use small, flatblade screw-

driver to carefully open fuse

receptacle, rotate fuse 180˚,

re-install fuse, and close fuse

receptacle.

• Connect female end of power cord to

Media Converter Rack.

• Connect male end of power cord to external AC outlet.

• Set ON/OFF switch to “I”.

Fuse

OFF

Rubber Grommet

Power

Receptacle

Tabla de contenidos

Otros manuales de Convertidor de medios de Transition Networks

Transition Networks

Transition Networks C/E-CX-FRL-04 Manual de usuario

Transition Networks

Transition Networks FBRM1XXX-1XX Manual de usuario

Transition Networks

Transition Networks CSETF1011-205 Manual de usuario

Transition Networks

Transition Networks C/F-SM-MM-06 Manual de usuario

Transition Networks

Transition Networks E-100BTX-FX-05 Manual de usuario

Transition Networks

Transition Networks M/GE-PSW-SX-01 Manual de usuario

Transition Networks

Transition Networks PS-CF-01(SC) Manual de usuario

Transition Networks

Transition Networks CGFEB1013-100 Manual de usuario

Transition Networks

Transition Networks E-CX-FRL-03 Manual de usuario

Transition Networks

Transition Networks F-SM-MM-02(LH) Manual de usuario

Transition Networks

Transition Networks SISTG10 211-LR Series Manual de usuario

Transition Networks

Transition Networks CGETF1013-100 Manual de usuario

Transition Networks

Transition Networks C/E-PSW-FX-03(LH) Manual de usuario

Transition Networks

Transition Networks E-TX-SX-02 Manual de usuario

Transition Networks

Transition Networks CSDTF30xx-11x Manual de usuario

Transition Networks

Transition Networks FBRM1XXX-1XX Manual de usuario

Transition Networks

Transition Networks CDFTF1111-100 Manual de usuario

Transition Networks

Transition Networks CSDTF3011-110 Manual de usuario

Transition Networks

Transition Networks E-CX-TBT-03 Manual de usuario

Transition Networks

Transition Networks E-TBT-FRL-N-02 Manual de usuario

Transition Networks

Transition Networks SSRFB10xx-100 Manual de usuario

Transition Networks

Transition Networks C/T1E1-CF-01 Manual de usuario

Transition Networks

Transition Networks AS4TEF10xx-10x Manual de usuario

Transition Networks

Transition Networks M/GE-xSW-SFP-01-xx-U Series Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario