Transition Networks CDFTF1111-100 Manual de usuario

Installation . . . . . . . . . . . . . . . . . .5

Operation . . . . . . . . . . . . . . . . . . .7

Technical Specifications . . . . . . . .8

Cable Specifications . . . . . . . . . . .9

Troubleshooting . . . . . . . . . . . . .10

Compliance Information . . . . . . .12

User’s Guide

CDFTFxxxx-10x

Slide-in-Module Media Converter

• Telco Network

• Copper to Fiber

• 100Base-TX to 100Base-FX

Transition Networks CDFTFxxxx-10x series dual-

port media converters are designed to be installed in

a CPSMC1850-150 PointSystem™ chassis. The

CDFTFxxxx-10x connects twisted-pair copper Telco

signals (received at the back of the CPSMC1850-150

chassis) to fiber-optic cable ports on each

CDFTFxxxx-10x series media converter (installed at

the front of the CPSMC1850-150 chassis).

Part Number Copper - Twisted-pair

Telco signals

Fiber-Optic - Two (2) external

100Base-FX ports

CDFTF1111-100 Two (2)

internal signals

ST, 1300 nm multimode

2 km (1.2 miles)*

CDFTF1313-100 Two (2)

internal signals

SC, 1300 nm multimode

2 km (1.2 miles)*

CDFTF1414-100 Two (2)

internal signals

SC, 1310 nm single mode

20 km (12.4 miles)*

CDFTF1717-100 Two (2)

internal signals

SC, 1550 nm single mode

80 km (49.7 miles)*

CDFTF1515-100 Two (2)

internal signals

SC, 1310 nm single mode

40 km (24.9 miles)*

CDFTF1616-100 Two (2)

internal signals

SC, 1310 nm single mode

60 km (37.3 miles)*

* Typical maximum cable distance. Actual distance is dependent upon the

physical characteristics of the network installation.

CDFTFxxxx-10x

224-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

CDFTF2929-100 and CDFTF2929-101 are intended to be installed in the same

network where one is the local converter and the other is the remote converter.

CDFTF2929-102 and CDFTF2929-103 are intended to be installed in the same

network where one is the local converter and the other is the remote converter.

* Typical maximum cable distance. Actual distance is dependent upon the

physical characteristics of the network. (TX) = transmit, (RX) = receive

Part Number Copper - Twisted-pair

Telco signals

Fiber-Optic - Two (2) external

100Base-FX ports

CDFTF2929-100 Two (2)

internal signals

SC, 1310 mn (TX)/1550 nm (RX)

20 km (12.4 miles)*

CDFTF2929-101 Two (2)

internal signals

SC, 1550 mn (TX)/1310 nm (RX)

20 km (12.4 miles)*

CDFTF2929-102 Two (2)

internal signals

SC, 1310 mn (TX)/1550 nm (RX)

40 km (24.8 miles)*

CDFTF2929-103 Two (2)

internal signals

SC, 1550 mn (TX)/1310 nm (RX)

40 km (24.8 miles)*

Part Number Description

CPSMC1850-150 18-slot PointSystem™ chassis with two (2) external RJ-21

Telco connectors. **

21HC45-6 Telco cable with RJ-21 connector at one end and twelve (12)

RJ-45 connectors at the other end.

21HC21-6 Telco cable with RJ-21 connectors at both ends.

Related Transition Networks Equipment (sold separately)

**For more information on the CPSMC1850-150 chassis, see the user’s guide on-

line at www.transition.com

CPSMC1850-150 Chassis

The CPSMC1850-150 PointSystem™ chassis provides two (2) 50-pin Telco

connectors installed at the chassis back. The two Telco 50-pin connectors

concentrate a total of 24 UTP connections, which are distributed to twelve

(12) installation slots in the front of the CPSMC1850-150 chassis.

RJ-21 Telco connector #2

RJ-21 Telco connector #1

[email protected] -- Click the “Transition Now” link for a live Web chat.

Telco Cables and Signals

The two kinds of Telco cables available from Transition Networks are pictured

below:

The signals from the Telco connectors are distributed as follows:

• Signals from Telco connector #2 go to chassis slots 7 - 12.

• Signals from Telco connector #1 go to chassis slots 13 - 18.

11 12 13 14 15 16 17

239

457

{

Telco connector #2 Telco connector #1

10BASE-T INPORT

MCCM10

MGMT MASTER

OUTPORT

DB-9

12C 12C-1TERM INIT

CETTF100

LKF PWR

RXF

RXC LKC

10BASE-T

10BASE-FL

Media

Conversion

Center

Power

In Use

Power

In Use

LNK

PWR

RESET

DB-9

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

In order to fully utilize the Telco option on the CPSMC1850-150 chassis, the

Transition Networks CDFTFxxxx-10x is required and it must be installed in

slots 7 through 18.

Please note:

• Slots 1-6 on the CPSMC1850-150 are designed for any Transition

Networks media converter slide-in-module.

• Slots 7-18 on the CPSMC1850-150 can accommodate any Transition

Networks media converter slide-in-module. However the Telco option

will not function unless a CDFTFxxxx-10x media converter is installed in

those slots.

21HC45-6:

one (1) RJ-21 connector

and 12 RJ-45 connectors

21HC21-6:

two (2) RJ-21 connector

CDFTFxxxx-10x

424-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

The chart also shows how the signals are distributed to either the UPPER or

LOWER port on the CDFTFxxxx-10x (see figure below).

25 1

50 26

The figure to the right illustrates the locations

of pins 1-50 on the Telco connector.

10BASE-T INPORT

MCCM10

MGMT MASTER

OUTPORT

DB-9

12C 12C-1TERM INIT

CETTF100

LKF PWR

RXF

RXC LKC

10BASE-T

10BASE-FL

Media

Conversion

Center

Power

In Use

Power

In Use

LNK

PWR

RESET

DB-9

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

lower ports

upper ports

Telco Connectors and Signals -- Continued

The chart below shows the 50 signals that go through each Telco connector on

the CPSMC1850-150 to slots 7-12 (Telco connector #2) OR to slots 13-18 (Telco

connector #1).

{

upper{

lower{

upper{

lower {

upper{

lower {

upper{

lower {

upper{

lower {

upper{

lower {

Pin # Signal Pin # Signal

1 Port 1 Transmit - 26 Port 1 Transmit +

2 Port 1 Receive - 27 Port 1 Receive +

3 Port 2 Transmit - 28 Port 2 Transmit +

4 Port 2 Receive - 29 Port 2 Receive +

5 Port 3 Transmit - 30 Port 3 Transmit +

6 Port 3 Receive - 31 Port 3 Receive +

7 Port 4 Transmit - 32 Port 4 Transmit +

8 Port 4 Receive - 33 Port 4 Receive +

9 Port 5 Transmit - 34 Port 5 Transmit +

10 Port 5 Receive - 35 Port 5 Receive +

11 Port 6 Transmit - 36 Port 6 Transmit +

12 Port 6 Receive - 37 Port 6 Receive +

13 Port 7 Transmit - 38 Port 7 Transmit +

14 Port 7 Receive - 39 Port 7 Receive +

15 Port 8 Transmit - 40 Port 8 Transmit +

16 Port 8 Receive - 41 Port 8 Receive +

17 Port 9 Transmit - 42 Port 9 Transmit +

18 Port 9 Receive - 43 Port 9 Receive +

19 Port 10 Transmit - 44 Port 10 Transmit +

20 Port 10 Receive - 45 Port 10 Receive +

21 Port 11 Transmit - 46 Port 11 Transmit +

22 Port 11 Receive - 47 Port 11 Receive +

23 Port 12 Transmit - 48 Port 12 Transmit +

24 Port 12 Receive - 49 Port 12 Receive +

25 N.C. 50 N.C.

Chassis Slot

#7 or 13

Chassis Slot

#8 or 14

Chassis Slot

#9 or 15

Chassis Slot

#10 or 16

Chassis Slot

#11 or 17

Chassis Slot

#12 or 18

[email protected] -- Click the “Transition Now” link for a live Web chat.

Install the Slide-in-Module

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when installing the CDFTFxxxx-10x. Failure to observe this

caution could result in damage to, and subsequent failure of, the media

converter.

To install the CDFTFxxxx-10x into the CPSMC1850-150 PointSystem™

chassis:

1. Locate an empty installation slot on the PointSystem™ chassis.

2. Carefully slide the slide-in-module into the installation slot, aligning the

module’s circuit board with the installation guides.

3. Ensure that the module is firmly seated inside the chassis.

4. Push in and rotate the the attached panel fastener screw clockwise to

secure the module to the chassis front.

CAUTION: Slots in the PointSystem™ chassis without a slide-in-module

installed MUST have a protective plate covering the empty slot for Class A

compliance.

10BASE-T INPORT

MCCM10

MGMT MASTER

OUTPORT

DB-9

12C 12C-1TERM INIT

CETTF100

LKF PWR

RXF

RXC LKC

10BASE-T

10BASE-FL

Media

Conversion

Center

Power

In Use

Power

In Use

LNK

PWR

RESET

DB-9

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

CDFTF100

Fiber Port #1

Fiber Port #2

panel fastener screw

Installation

Set the Hardware/Software Jumper

• The jumper is located on the circuit board and is labeled “H” and “S”.

• Use small needle-nose pliers to set the jumper.

Hardware The media converter settings such as

AutoCross and Link Pass-Through cannot be

changed.

Software The media converter settings are determined

by the most-recently saved, on-board

microprocessor settings. Software Mode

Hardware Mode

CDFTFxxxx-10x

624-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Installation -- Continued

NOTE: The media converter does not support Auto-Negotiation. Set the

external devices to forced 100 Mb/s full-duplex.

Connect the Telco Copper Cable

CAUTION: The twisted-pair copper Telco cables must be less than 60 m (196

ft.). Failure to observe this caution could cause data transfer to fail.

1. Locate the 100Base-TX cable with the male 50-pin Telco connector at

one end and with twelve (12) RJ-45 connectors at other end (P/N

21HC45-6). Alternatively, the male 50-pin Telco connector at both ends

(P/N 21HC21-6) may also be used.

2. Connect the male 50-pin Telco cable connector to the female 50-pin

Telco connector at the chassis back.

3. Connect the twelve (12) RJ-45 connectors or the male 50-pin Telco cable

connector at the other cable end to the 100Base-TX Telco device(s).

4. Repeat steps 3 and 4 to connect the second 100Base-TX Telco cable to

the second 50-pin Telco connector at the chassis back.

Connect the Fiber Cable

1. Locate or build IEEE 803.2™compliant 100Base-FX fiber cable with

male, two-stranded TX to RX connectors installed at both ends.

2. Connect the fiber cables to the CDFTFxxxx-10x media converter as

described:

• Connect the male TX cable connector to the female TX port.

• Connect the male RX cable connector to the female RX port.

3. Connect the fiber cables to the other device (another media converter,

hub, etc.) as described:

• Connect the male TX cable connector to the female RX port.

• Connect the male RX cable connector to the female TX port.

Power the Media Converter

The slide-in-module media converter is powered through the Transition

Networks PointSystem™ chassis.

Connect the fiber cable

to the media converter

as shown.

Connect the fiber cable

to the other device

(media converter,

hub, etc.) as shown

[email protected] -- Click the “Transition Now” link for a live Web chat.

Product Features

AutoCross™

When the AutoCross feature is activated, it allows either straight-through

(MDI) or crossover (MDI-X) copper cables to be used when connecting to

100Base-TX devices. AutoCross determines the characteristics of the

connection and automatically configures the unit to link up, regardless if the

copper cable is MDI or MDI-X configuration.

Link Pass Through

The Link Pass-Through feature allows the media converter to monitor both the

fiber and copper RX (receive) ports for loss of signal. In the event of a loss of

an RX signal (1), the media converter will automatically disable the TX

(transmit) signal (2), thus, “passing through” the link loss (3). The far-end

device is automatically notified of the link loss (4), which prevents the loss of

valuable data unknowingly transmitted over an invalid link.

Media

Converter A

Media

Converter B

Near-End

Device

Far-End

Device

original fault

on the copper link media converter B

disables the copper lin

media converter A

disables the fiber TX link

media converter B

loses the fiber RX link

Operation

Status LEDs

Use the status LEDs to monitor the media converter

operation in the network

PWR Power:On = Connection to external AC power.

TL1 Twisted-Pair Link 1: On = A link on the twisted-

pair Telco connection to media converter #1.

FL1 Fiber Link 1: On = A link on the fiber

connection to media converter #1.

AC1 Activity 1: Flashing = Activity on media

converter #1.

TL2 Twisted-Pair Link 2: On = A link on the

twisted-pair Telco connection to media

converter #2.

FL2 Fiber Link 2: On = A link on the fiber

connection to media converter #2.

AC2 Activity 2: Flashing = Activity on media

converter #2.

CDFTF100

Fiber Port #1

Fiber Port #2

PWR

AC1

TL1

FL1

AC2

TL2

FL2

CDFTFxxxx-10x

824-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Technical Specifications

For use with Transition Networks Model CDFTFxxxx-10x or equivalent.

Standards IEEE 802.3™

Data Rate 10 Mb/s

Dimensions 3.4" x 0.86" x 5.0" (86 x 22 x 127 mm)

Weight 3 oz (91 g) (approximate)

Power Consumption 6.8 watts

MTBF 484,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)

1,359,000 hours (Bellcore7 V5.0)

Environment Tmra*: 0 to 60°C (32 to 140°F )

Storage Temp: -20 to 85°C (-4 to 185°F)

Humidity: 5 to 95%, non condensing

Altitude: 0 to 10,000 feet

Warranty Lifetime

*Manufacturer’s rated ambient temperature: Tmra range for this slide-in-module

depends on the physical characteristics and the installation configuration of the

Transition Networks PointSystem™ chassis in which this slide-in-module will be

installed.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,

Subchapter J applicable at the date of manufacture.

CAUTION: Visible and invisible laser radiation when open. Do not stare into

the beam or view directly with optical instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other

than those specified herein may result in hazardous radiation exposure.

Operation -- Continued

SNMP

Use SNMP at an attached terminal or at a remote location to monitor the

media converter by monitoring:

• Media converter power.

• Copper link status on media converter #1.

• Fiber link status on media converter #1.

• Activity on media converter #1.

• Copper link status on media converter #1.

• Fiber link status on media converter #1.

• Activity on media converter #1.

Also, use SNMP to enter network commands that:

• Enable/disable AutoCross.

See the on-line documentation that comes with Transition Networks

FocalPoint™ software for commands and usage at www.transition.com.

[email protected] -- Click the “Transition Now” link for a live Web chat.

Cable Specifications

The physical characteristics must meet or exceed IEEE 802.3™ specifications.

Telco Copper Cable Maximum cable distance = 60 m (197 ft.)

Category 5: (minimum requirement)

Gauge 24 to 22 AWG

Attenuation 22.0 dB /100m @ 100 MHz

(See page 4 for the Telco cable signal distribution over the 50-pin

connector at the back of the CPSMC1850-150 PointSystem™ chassis.)

Fiber Cable

Bit Error Rate: <10-9

Single mode fiber (recommended): 9 µm

Multimode fiber (recommended): 62.5/125 µm

Multimode fiber (optional): 100/140, 85/140, 50/125 µm

CDFTF1111-100 1300 nm multimode

CDFTF1313-100 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

CDFTF1414-100 1310 nm single mode

Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber-optic Receiver Sensitivity: min: -31.0 dBm max: -8.0 dBm

Link Budget: 16.0 dB

CDFTF1515-100 1310 nm single mode

Fiber-optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 26.0 dB

CDFTF1616-100 1310 nm single mode

CDFTF1717-100 1550 nm single mode

Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 29.0 dB

CDFTF2929-100 1310 nm (TX)/1550 nm (RX) simplex

CDFTF2929-101 1550 nm (TX)/1310 nm (RX) simplex

Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

CDFTF2929-102 1310 nm (TX)/1550 nm (RX) simplex

CDFTF2929-103 1550 nm (TX)/1310 nm (RX) simplex

Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm

Link Budget: 25.0 dB

The fiber optic transmitters on this device meets Class I Laser safety

requirements per IEC-825/CDRH standards and complies with 21

CFR1040.10 and 21CFR1040.11.

CDFTFxxxx-10x

10 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Troubleshooting

If the media converter fails, isolate and correct the fault by determining the

answers to the following questions and then taking the indicated action:

1. Is the Power LED on the media converter illuminated?

• Is the media converter inserted properly into the chassis?

• Is the power cord properly installed in the chassis and at the external

power source?

• Does the external power source provide power?

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 2.

2. Is the Twisted-Pair Link 1 LED illuminated?

• Check the twisted-pair Telco cables for proper connection.

• Ensure that the twisted-pair copper Telco cable distance does not

exceed 60 meters.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 3.

3. Is the Fiber Link 1 LED illuminated?

• Check the fiber cables for proper connection.

• Verify that the TX and RX cables on media converter are connected

to RX and TX ports, respectively, on the other device.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 4.

4. Is the Activity 1 LED illuminated?

• Verify that data is being sent from the external devices.

• Verify that all external devices are set to forced 100 Mb/s full-duplex

for full-duplex operation.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 5.

5. Is the Twisted-Pair Link 2 LED illuminated?

• Check twisted-pair Telco cables for proper connection.

• Ensure that the twisted-pair copper Telco cable distance does not

exceed 60 meters.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 6.

[email protected] -- Click the “Transition Now” link for a live Web chat.

Technical support is available 24 hours a day:

US / Canada: 1-800-260-1312, International: 00-1-952-941-7600

Chat live via the Web with Transition Networks Technical Support.

Log onto www.transition.com and click the Transition Now link.

Ask a question anytime by sending an e-mail to our technical support staff.

[email protected]

Transition Networks, 6475 City West Parkway, Minneapolis, MN 55344, USA

telephone: 952-941-7600, toll free: 800-526-9267, fax: 952-941-2322

Declaration of Conformity

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 USA

Model: CDFTFxxxx-10x Series Media Converters

Part Number(s): CDFTF1111-100, CDFTF1313-100, CDFTF1414-100, CDFTF1515-100,

CDFTF1616-100, CDFTF1717-100, CDFTF2929-100, CDFTF2929-101,

CDFTF2929-102, CDFTF2929-103

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the

CDFTFxxxx-10x

to which this declaration refers is in

conformity with the following standards.

CISPR 22:1997+A1:2000; EN 55022:1998+A1:2000 Class A; EN 55024:1998;

FCC Part 15 Subpart B; EN 61000-3-2:1995+A14:2000; EN61000-3-3:1995

I, the undersigned, hereby declare that the equipment specified above conforms to the above

Directive(s) and Standard(s).

May 1, 2002

Stephen Anderson, Vice-President of Engineering Date

Troubleshooting -- Continued

6. Is the Fiber Link 2 LED illuminated?

• Check the fiber cables for proper connection.

• Verify that the TX and RX cables on the media converter are

connected to the RX and TX ports, respectively, on the other device.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 7.

7. Is the Activity 2 LED illuminated?

• Verify that data is being sent from the external devices.

• Verify that all external devices are set to forced 100 Mb/s full-duplex

for full-duplex operation.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

Trademark Notice

All trademarks and registered trademarks are the property of their respective owners.

means - graphic, electronic, or mechanical - without written permission from Transition

Networks.

Printed in the U.S.A. 33217.D

Compliance Information

CISPR22/EN55022 Class A + EN55204

CE Mark

FCC Regulations

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference, in which case the user will be required to correct the

interference at the user's own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus

set out on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

European Regulations

Warning This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können

bei Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für

Gegenmaßnahmen verantwortlich.

Attention! Ceci est un produit de Classe A. Dans un environment domestique, ce produit

risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de

prende les measures spécifiques appropriées.

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-

Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der

Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über

Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer

Konformität.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Transition Networks

Transition Networks

Transition Networks SBFTF10XX-10X Manual de usuario

Transition Networks

Transition Networks CBFTF10xx-1xx Manual de usuario

Transition Networks

Transition Networks C/F-SM-MM-05 Manual de usuario

Transition Networks

Transition Networks S3290 Manual de usuario

Transition Networks

Transition Networks C/F-SM-MM-02(LH) Manual de usuario

Transition Networks

Transition Networks CCSF30XX-100 Manual de usuario

Transition Networks

Transition Networks FXC1115T Manual de usuario

Transition Networks

Transition Networks Milan MIL-RC6113SX-V2 Manual de usuario

Transition Networks

Transition Networks E-100BTX-FX-N-01 Manual de usuario

Transition Networks

Transition Networks CSDTF30xx-11x Manual de usuario

Transition Networks

Transition Networks SISTF1011-110-LR Manual de usuario

Transition Networks

Transition Networks C/T1E1-CF-01 Manual de usuario

Transition Networks

Transition Networks C4TEF1011-110 Manual de usuario

Transition Networks

Transition Networks SISTG10 211-LR Series Manual de usuario

Transition Networks

Transition Networks M/E-TX-FX Series Manual de usuario

Transition Networks

Transition Networks C/HSTR-CF-01(SC) Manual de usuario

Transition Networks

Transition Networks SBFTF1011-110 Manual de usuario

Transition Networks

Transition Networks CFETF1011-205 Manual de usuario

Transition Networks

Transition Networks SAPTF33 series Manual de usuario

Transition Networks

Transition Networks C/TR-CF-01(SM) Manual de usuario

Transition Networks

Transition Networks SFMFF1314-280 Manual de usuario

Transition Networks

Transition Networks Stand-Alone Media Converter S4TEF10xx-11x Manual de usuario

Transition Networks

Transition Networks E-100BTX-FRL-03(SC) E-100BTX-FRL-03(SM) Manual de usuario

Transition Networks

Transition Networks CGFEB1xxx-15x Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario