TrailFX DHS015B Manual de usuario
Page 1 of 4
TrailFX Drop Down Step
Part No. DHS015B / DHS016B
Fits: 2009-2018 Ram 1500 Crew Cab / Quad Cab (Incl. Clas-
sic) 2010-2019 Ram 2500/3500 Crew Cab / Quad Cab
Product image
TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF
THE TAILGATE VENT COVER CAREFULLY.
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
PARTS LIST:
Item Qty Part Description Tools Needed
11Step Bar Driver Side 10 MM SOCKET & WRENCH
21Step Bar Passenger Side 13 MM SOCKET & WRENCH
31Mounting Bracket Left 14 MM SOCKET & WRENCH
41Mounting Bracket Right 15 MM SOCKET & WRENCH
58M8 Riv-Nut ALLEN KEY SET
612 M8 Bolt RATCHET
712 M8 Lock Washer TORQUE WRENCH
86M8 Flat Washer Big
96M8 Flat Washer Small
10 12 M6 Flange Nut
11 12 M6 Flat Washer
12 12 M6 Button Head Bolt
13 12 M10 Flange Bolt
14 12 M10 Flange Nut
15 6M8 Nut Plate
16 6M10 Plastic Retainer
17 1Long M8 Bolt
ALIGN THE STEP BARS AS DESIRED AND TIGHTEN ALL M10 FASTENERS TO 30
ft. - lbs., THE M8 FASTENERS TO 15 ft.-lbs, AND THE M6 FASTNERS TO 7 ft-lbs.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
60 min Drilling
Required
Cutting Not Re-
quired
Mounting Kit Images
ITEM 3 ITEM 4
Page 2 of 4
1. If factory riv-certs are present, skip to step 3. If no factory riv-nuts
are present, skip to step 2.
2. Install 1 hex riv-nut onto rocker panel using 2 washers an M10
flange nut and a long M8 bolt. Use a wrench to hold the M10 flange
nut in place while you torque the bolt. Be sure to apply pressure
while torqueing the bolt to keep the riv nut from falling off of the
rocker panel. Do this to all 6 mounting locations. See Figure 1-3.
Rear Passenger
Side Shown
10
8
5
APPLY PRESSURE
INSTALL HEX
RIV-NUT
M8 NUT PLATE
WILL BE USED
HERE
15
16
INSTALLATION PROCEDURE
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
17
3. Grab a M8 nut plate and M10 plastic retainer and install to
the rocker panel. The nut plate will be used for the mount
location opposite of the riv-nut. See Figure 4.
Page 3 of 4
INSTALLATION PROCEDURE
4. Starting from the driver side: Loosely install the fr ont
mounting bracket onto the rocker panel by using (2) long M8
hex cap screws, (2) M8 lock washers, (1) M8 big flat wash-
ers, and (1) small flat washers. For the pinch weld, attach
bracket by using the provided black zinc M6 hardware.
Note: Drilling of two 1/4” holes might be necessary on
pinch weld if factory holes are not present. Before drilling
place masking tape on drill surface to prevent paint chip-
ping.) See Figure 5 & 6.
FIGURE 5
Loosely install bracket
using M8 hardware
Drill two 1/4” holes
(If no pre-existing
holes are present)
Front driver side shown
Front driver side shown
FIGURE 6
Loosely install bracket
using M8/M6 hardware
678
910
11
12
Center and Rear driver side shown
13 14
FIGURE 8
FIGURE 7
3
3
4
5. At the center and rear driver side location install similarly as
the front driver. Repeat Steps 3-4 on the passenger side of the
vehicle. See Figure 7.
6. Loosely install step bars respectively to either side using the
M10 hardware provided with the step bars. See Figure 8.
7. Align and adjust the step bars as needed and fully tighten all
hardware.
8. See Figure 9 for reference.
Page 4 of 4
COMPLETE INSTALLATION
FRONT
FIGURE 9 Driver Side Shown
Item 4 Item 3
Item 4
Page 5 of 4
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of pur-
chase by the original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness for a
particular purpose or an intended use. If the product is found to be defective, KAO may replace or repair the product at our option,
when the product is returned prepaid, with proof of purchase. Alteration to, improper installation, or misuse of this product voids the
warranty. KAO’s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for any
incidental or consequential loss or damage.
Check out these other TrailFX Products!!
PRODUCT CARE
1.
FAQ’s
1. Mounting bracket are not getting Installed properly.
In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver / Passenger side
mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue.
2. Products are thumping / rattling after installation.
Please ensure that all required mounting brackets / hardware’s are installed & tighten correctly. Suggest using white lithium / regular grease between the
metal to metal contact surfaces.
3. Missing / Excess Hardware.
Recheck hardware count as per the part list.
4. Product not installing properly.
Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.
Learn more about running boards on our website.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Accesorios para automóviles de TrailFX
TrailFX
TrailFX 21020 Series Manual de usuario
TrailFX
TrailFX FX1009 Manual de usuario
TrailFX
TrailFX 211102S Manual de usuario
TrailFX
TrailFX FCLR003B Manual de usuario
TrailFX
TrailFX A1543S Manual de usuario
TrailFX
TrailFX JL05RF Manual de usuario
TrailFX
TrailFX FX3001 Manual de usuario
TrailFX
TrailFX A1546T Manual de usuario
TrailFX
TrailFX FX3004 Manual de usuario
TrailFX
TrailFX 150361 Manual de usuario
TrailFX
TrailFX 8038H Manual de usuario
TrailFX
TrailFX A7060S Manual de usuario
TrailFX
TrailFX RBA006TI Manual de usuario
TrailFX
TrailFX FX3006 Manual de usuario
TrailFX
TrailFX Tonneau Manual de usuario
TrailFX
TrailFX A4012S Manual de usuario
TrailFX
TrailFX 5059XH Manual de usuario
TrailFX
TrailFX FX3002 Manual de usuario
TrailFX
TrailFX FHDB006TI Manual de usuario
TrailFX
TrailFX BR010T Manual de usuario
