TrailFX B1603S Manual de usuario

Page 1of 5

PARTS LIST:

Qty

Part Description

Qty

Part Description

3.5in Oval Bull Bar Assembly

12mm Plastic Retainers

Driver/left Frame Bracket

12mm x 32mm OD x 3mm Flat Washer

Passenger/Right Frame Bracket

12-1.75mm Nylon Lock Nut

Driver/left Bull Bar Mounting Bracket

10-1.5mm x 30mm Hex Bolt

Passenger/right Bull Bar Mounting Bracket

10mm x 27mm OD x 3mm Flat Washer

12-1.75mm x 35mm Bolt Plates

10-1.5mm Nylon Locknut

3.5" Oval Bull Bar

Part No. B1603S/B

Fits: 2011-2016 Chevrolet Silverado/GMC Sierra 2500/3500

Passenger/right Side

Frame Bracket

Driver/left Side

Frame Bracket

Passenger/right Side

Bull Bar Bracket

Driver/left Side

Bull Bar Bracket

(4) 12mm Bolt Plates

with Plastic Retainer

ASSISTANCE IS RECOMMENDED.

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

DO NOT OVER TORQUE.STANDARD OPERATING LOAD FOR TIGHTEN

BODY MOUNT NUTS & BOLTS VARIES FROM

FOOT POUND.

60-180 min

Drilling Not

Required

Cutting

Required

Page 2of 5

INSTALLATION PROCEDURE:

CUTTING MAY BE REQUIRED. INSTALLATION MAY INTERFERE WITH BUMPER MOUNTED

PARKING SENSORS. ASSISTANCE IS RECOMMENDED.

NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not

required, but strongly recommended. If local/state law requires a front license plate, license plate relocation

kit is available.

1. Starting at the driver side, remove the factory tow hook if equipped, (Figures 1A & 1B). NOTE: This Bull

Bar is not compatible with the factory tow hooks and they cannot be reinstalled. IMPORTANT: On some

model years, with and without tow hooks, the pocket in the plastic bumper may need to be trimmed or

completely cut out, (Figure 1A). Use a sharp knife or hacksaw blade and carefully cut out the pocket to

clear the Bull Bar Brackets. Only cut enough to clear the Brackets.

2. Insert (1) 12mm Bolt Plate, (Figure 3), into the end of the frame channel, (Figure 4), and out through

the hole in the bottom of the frame. Insert a second Bolt Plate into and out the hole in the outer side of

the frame, (factory hole for tow hook bolt), (Figures 4 & 5). Thread 12mm Plastic Retainers onto the Bolt

Plates to help hold them in place as needed. NOTE: Plastic Retainers are not required for installation

and use is optional.

Front

Fig 1B) Remove the tow hook and hardware,

(Driver/left tow hook pictured from below bumper)

(Fig 3) 12mm Bolt Plate with hardware

(Fig 4) Driver/left side tow hook opening pictured

(2) 12mm Bolt Plates

Remove the factory tow

hook and hardware. Tow

hook will not be reinstalled

Fig 1A

Page 3of 5

3. Select the driver side Frame Bracket, (Figure 5). Position the Frame Bracket onto the outside of the

frame channel and over the (2) Bolt Plates, (Figure 6). Secure the Bracket to the frame and Bolt Plates

with (2) 12mm Flat Washers and (2) 12mm Nylon Lock Nuts. Leave hardware loose at this time.

4. Next, select the driver side Bull Bar Mounting Bracket, (Figure 7). Attach the Bull Bar Bracket to the

inside of the Frame Bracket with the included (2) 10mm x 30mm Hex Bolts, (4) 10mm Flat Washers and

(2) 10mm Nylon Lock Nuts, (Figure 7). Leave hardware loose at this time. NOTE: On some models, it

may be possible or simpler to bolt the Frame and Mounting Brackets together first and install as one

piece.

(Fig 5) Attach driver/left Frame Bracket

to 12mm Bolt Plates in end of frame

(2) 12mm Flat Washers

(2) 12mm Nylon Lock

Nuts

(2) 12mm Bolt Plates

(2) 12mm Plastic

Retainers (use is

optional)

(Fig 5) Attach driver/left Frame Bracket

to 12mm Bolt Plates in end of frame

(2) 12mm Flat Washers

(2) 12mm Nylon Lock Nuts

(2) 12mm Bolt Plates

(2) 12mm Plastic

Retainers (use is

optional)

(2) 12mm Flat Washers

(2) 12mm Nylon Lock Nuts

Front

(Fig 6) Driver/left Frame Bracket pictured

Page 4of 5

5. Starting at the bottom of the frame, tighten the lower 12mm Frame Bracket mounting hardware first then move to

the side of the frame. Fully tighten Frame Bracket to 12mm Bolt Plate hardware only at this time. Do not tighten the

10mm Bull Bar Bracket hardware.

6. Repeat Steps 1—5for passenger side Frame and Mounting Bracket installation.

7. With assistance, position the Bull Bar assembly up to the inside of the Mounting Brackets. Attach the Bull Bar to

the Brackets with the included (4) 10mm x 30mm Hex Bolts, (8) 10mm Flat Washers and (4) 10mm Nylon Lock

Nuts, (Figure 8). Do not fully tighten hardware at this time.

8. Level and adjust the Bull Bar and fully tighten all remaining hardware.

9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

(2) 10mm x 30mm Hex Bolts

(4) 10mm Flat Washers

(2) 10mm Nylon Lock Nuts

(Fig 7) Attach driver/left Bull Bar

Bracket to inside of Frame Bracket

(Fig 8) Attach Bull Bar to inside of Mounting Brackets

(2) 10mm x 30mm Hex Bolts

(4) 10mm Flat Washers

(2) 10mm Nylon Lock Nuts

Page 5of 5

FAQ’s

1. Hardware’s are not of correct size.

In GMC / Chevrolet truck model 2006 & up, customer needs to reuse the factory body bolts to install the bracket. If your vehicle is not

GMC / Chevrolet 2006 & up, ensure that holes are not partially covered with any plastic grommet or rust? If it is, remove the plastic

grommet & rust from the thread holes & re-try the installation.

2. Mounting Bracket are not getting Installed properly.

In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver /

Passenger side mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue.

3. Products are thumping / rattling after installation.

Ensure that all required mounting brackets / hardware’s are installed & tighten correctly. Suggest using white lithium / regular grease

between the metal to metal contact surfaces.

4. Side Bar is not aligning with vehicle / Step Pads are not aligning with vehicle doors.

Side bar may be interchanged or mounting brackets are not installed at the correct position in the vehicle. Refer Parts identification guide.

5. Missing / Excess Hardware.

Recheck hardware count as per the part list.

6. Product not installing properly.

Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.

Check out these other TrailFX Products!!

PRODUCT CARE

Periodically check the product to ensure all fasteners are tight and components are intact.

Regular waxing is recommended to protect the finish of the product.

Use ONLY Non-Abrasive automotive wax. Use of any soap, polish or wax that contains an abrasive is detrimental and can scratch the

finish leading to corrosion.

Aluminum polish may be used to polish small scratches and scuffs for Stainless Steel finish.

Mild soap may be used to clean the product for both Stainless Steel and Black finish.

Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of purchase by the

original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness for a particular purpose or an

intended use. If the product is found to be defective, KAO may replace or repair the product at our option, when the product is returned prepaid,

with proof of purchase. Alteration to, improper installation, or misuse of this product voids the warranty. KAO’s liability is limited to repair or

replacement of products found to be defective, and specifically excludes liability for any incidental or consequential loss or damage.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para automóviles de TrailFX

TrailFX

TrailFX 110701S Manual de usuario

TrailFX

TrailFX A7057S Manual de usuario

TrailFX

TrailFX TFX5522 Manual de usuario

TrailFX

TrailFX A0057S/B Manual de usuario

TrailFX

TrailFX TG03X Manual de usuario

TrailFX

TrailFX TFX1523 Manual de usuario

TrailFX

TrailFX JTOE004 Manual de usuario

TrailFX

TrailFX A7099S Manual de usuario

TrailFX

TrailFX J048T Manual de usuario

TrailFX

TrailFX RBA023TI Manual de usuario

TrailFX

TrailFX A0002S Manual de usuario

TrailFX

TrailFX FCLR006W Manual de usuario

TrailFX

TrailFX A0030S Manual de usuario

TrailFX

TrailFX A1537S Manual de usuario

TrailFX

TrailFX JL010RF Manual de usuario

TrailFX

TrailFX A7054S/B Manual de usuario

TrailFX

TrailFX 210101 Manual de usuario

TrailFX

TrailFX DHS001B Manual de usuario

TrailFX

TrailFX FHDNW002TI Manual de usuario

TrailFX

TrailFX G9022B Manual de usuario

TrailFX

TrailFX A1501S Manual de usuario

TrailFX

TrailFX A5006S Manual de usuario

TrailFX

TrailFX A0029S Manual de usuario

TrailFX

TrailFX FX3021 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario