TPI 600 Series Manual de usuario
Introduction
Congratulations
Thank you for purchasing TPI brand products. This meter is easy to use and is built to
last. It is backed by a 3 year limited warranty. Please remember to return you product
warranty registration card.
Product Description
The TPI 600 series is a hand held range of pressure meters and can be summarized as
follows.
TPI 610 - Single Input - 4 Function - single unit of pressure
TPI 615 - Single Input - 7 Function - 7 units of pressure
TPI 620 –Dual Input –differential –4 Function –single unit of pressure
TPI 625 –Dual Input –differential –7 Function –7 units of pressure
All these models measure over the range of -200.0 to +200.0 mbar. Each unit has
increased resolution of 0.01 mbar and automatically auto-ranges at + 19.00 mbar to 0.1
mbar resolution. Each model is supplied complete with carry pouch, battery and
instruction manual.
Page 3
www. .com information@itm.com1.800.561.8187
Safety Considerations
Warning: Please follow the manufacturer’s test procedure whenever possible. Make
sure the pressure to be measured is not outside the range of the TPI 610/615/620/625
meter
General Guidelines
Always
·Test the pressure meter before use to ensure it is operation properly
·Ensure that the connection hose you are using is free from kinks or splits
·Double check all connections before testing
Never
·Connect the Instrument to an unknown pressure source if the source is twice the
working pressure of the instrument the sensor will be damaged and may cause
injury to the user
·Tamper with the instrument or attempt to modify it in any way. Otherwise
accident and injury may occur and the warranty becomes void.
page 4
www. .com information@itm.com1.800.561.8187
Technical Data
Controls TPI 610/615/620/625
ON Present on all models switches instrument ‘On’for use
OFF Present on all models switches ‘Off’after use
ZERO Present on all models ‘Zero’s’the display ready of use
= Smoothing function to stabilize rapidly changing pressure readings
MAX Enables the user to recall & display both the
MIN maximum and minimum pressure recorded since the function was selected. Press
button once to actuate, twice to read minimum and three times to read maximum. To
cancel the function press ‘Zero’(TPI 615/625 only)
HOLD Maintains the reading on the LCD display (TPI 615/625 only)
UNITSSelects 7 units of pressure kPa, PSI, inHg, mmHg inH20, mbar (TPI 615/625
only)
page 5
www. .com information@itm.com1.800.561.8187
Features & Benefits
Autoranging - Provides high resolution & accuracy at low pressures where it is needed
Auto Power Off - Powers off after 40 minutes to conserve battery life.
Trim Mode - Smoothing function to stabilize erratic readings. It displays the average
value of 4 values previously measured.
Zero Function - Provide immediate push-button zeroing for Speed and accuracy.
Record Max/Min- Enables long term testing of pressure circuit to check for leaks.
(TPI 615/625 only)
Hold- Enables the user to freeze the display reading when working in cramped working
conditions, when the display is not visible. (TPI 615/625 only)
Units- Change the display value in any one of the following engineering units. kPs, PSI,
inHg, mmHg, inH20, mmH20 and mbar. (TPI 615/625 only)
page 6
www. .com information@itm.com1.800.561.8187
Pressure Conversion Table
Atmos Bars inHg
(0°C) inH20
(4°C) Lb/in2
(PSI) mmH
g
(torr)
mmH20 Pascals
Atmos 1 9.8692
3 x10 -
1
3.3420
7 x10 -
2
2.458
x 10 -
3
0.06804
6 1.316
x 10 -3
0.9677
x 10 -4 9.869
x 10 -6
Bars 1.01325 1 3.3864
x10 -2 2.491
x 10 -
3
6.8948
x 10 -2 1.333
x 10 -
3
0.9807
x 10 -4 1.000
x 10 -5
inHg
(0°C) 29.9213 29.53 1 7.355
x 10 -
2
2.036 3.937
x 10 -
2
2.89567
x 10 -3 2.953
x 10 -4
inH20
(4°C) 406.8 401.48 13.60 1 27.68 0.535
4 3.937
x 10 -2 4.014
x 10 -3
Lb/in2
(PSI) 14.69559
5 14.504 0.4912 3.612
7 x 10
-2
1 1.934
x 10 -
2
1.42232
3 x 10 -
3
1.4503
x 10 -4
mmHg
(torr) 760 750.06 25.400 1.868 51.715 1 7.35433
x 10 -2 7.502
x 10 -3
mmH2
0 10.33272
x 10 3 10.197
6 x 10
3
3.4544
x 10 2 25.40
0 703.07 13.59
9 1 0.101955
6
Pascals 1.01325
x 10 5 1.000
x 10 5 3.386
x 10 3 2.491
x 10 2
6.8948
x 10 3 1.333
x 10 2 9.8071 1
Page 7
www. .com information@itm.com1.800.561.8187
Step by Step Procedures
·Press the ‘ON’Key and the LCD display will be activated if it does not read 0.00
proceed as follows
·Press the ‘ZERO’key and the display should zero within +/- 0.05 if not repeat
until it does
·Connect pressure meter to installation or equipment to be tested using appropriate
hose connection in accordance with the manufacturers instructions
·The pressure reading will appear on the display. To activate the backlight in poor
light conditions press the ‘ON’key at any time
·If the reading is erratic or changing activate the smoothing function by pressing
the ‘=’key
·To freeze a reading in awkward or cramped working spaces press the ‘HOLD’
key (TPI 615/625 only)
·To record maximum & minimum pressures when establishing pressure decay or
carrying out gas line soundness testing press the ‘MAX/MIN’key (TPI 615/625
only)
·To convert the displayed pressure reading to another engineering unit depress the
‘UNIT’key anytime and scroll through to the desired units of pressure. (TPI
615/625 only)
page 8
www. .com information@itm.com1.800.561.8187
Accessories & Specifications
Standard accessories Part No
9V battery A009
Soft Pouch A600
Silicone Tube w/ ¼”barbed 1/8”NPT fitting A603
Optional Accessories Part No
3 metre (6 ft) nitrile rubber tubing A601
Large Zipped pouch A904
Specifications
Model
Features TPI 610 TPI 615 TPI 620 TPI 625
Auto Range -200.0 mbar to -200.0 mbar
Accuracy + (0.5% of reading + 5 Digits)
Over Pressure 500 mbar
Power Supply 9V
Relative
Humidity 0% to 80% (0°C to +40°C)
Operating Temp. 0°C to +40°C
Storage Temp. -10°C to +50°C
Auto Power Off 20 Minutes
Input Type Single Single Differential Differential
Trim Mode Yes Yes Yes Yes
Zero Adjust Yes Yes Yes Yes
Record Min/Max No Yes No Yes
Units 1 7 1 7
Data No Yes No Yes
In units there are kPa, PSI, inHG, mmHg, inH20, mmH20, mbar
page 9
www. .com information@itm.com1.800.561.8187
Maintenance
Battery Replacement:
The 610/615/620/625 will display a ‘BAT’symbol when the internal 9V battery needs
replacement. Replace battery as follows:
1. Ensure instrument is switched off
2. Loosen the six cross head screws on the back of the instrument
3. Remove the back cover
4. Remove old battery
5. Replace with new battery 9V NEDA 1604 or equivalent
6. Reassemble the instrument in reverse order from above being sure not to trap any
wires between the two helves of the case
7. Re-fit the six cross head screws being sure not to over tighten
Cleaning: Use a mild detergent and a slightly damp cloth to clean the surfaces of the
instrument.
page 10
www. .com information@itm.com1.800.561.8187
Trouble Shooting Guide
Problem Probable Cause
Unit does not zero Zero button has not been operated
Unit still does not zero If reading is greater than 0.05 and constantly fluctuation
return to local service centre.
‘Bat’appears on display Replace battery immediately 9V NEDA 1505 or equivalent
EC Declaration of Conformity
This is to certify that model 610/615/620/625 conform to the protection requirements of
the council directive 89/336/EEC, in the approximation of laws of the member states
relating to Electromagnetic compatibility be application of the following standards
EN50081-1 1992 Emissions Standard
EN50082-1 1992 Immunity Standard
To ensure conformity with these standards, this instrument must be operated in
accordance with the instructions and specifications given in this manual.
page 11
www. .com information@itm.com1.800.561.8187
3 Year Warranty
Warranty Statement
This TPI product is warranted to the purchaser against defect is materials and
workmanship for 3 years from the date of purchase.
Covered by TPI: Repair parts and labor; or replacement of the product at the option of
TPI. Normal transportation charges to the purchaser are also covered.
Not covered by TPI: Damage to the product which are the result of abuse, improper use
or maintenance are not covered. Any other expense, consequential damages, incidental
expenses including damages to property is not covered. Transportation expenses to the
company are not covered.
To obtain warranty performance: include with the product your name, address, phone
number, written description of the problem and proof of purchase date. Carefully package
and return to the address printed on the front of this instructions leaflet.
page 12
www. .com information@itm.com1.800.561.8187
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Instrumento de medición de TPI
TPI
TPI 637623600616 Manual de usuario
TPI
TPI 265 Manual de usuario
TPI
TPI The Value Leader 505 Manual de usuario
TPI
TPI 665L Manual de usuario
TPI
TPI 775 Manual de usuario
TPI
TPI 556 Manual de usuario
TPI
TPI The Value Leader 716N Manual de usuario
TPI
TPI SP341 Manual de usuario
TPI
TPI 1008 Manual de usuario
TPI
TPI DC710 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario