TP-Link TL-SF1016DS Manual de usuario

Business Networking Solution

Installation Guide

10/100Mbps Unmanaged Switch

TL-SF1016DS/TL-SF1016

TL-SF1024D/TL-SF1024

TL-SF1048

IAbout this Installation Guide

About this Installation Guide

This Installation Guide describes the hardware characteristics, installation methods and the

points that should be attended to during the installation. This Installation Guide is structured as

follows:

Chapter 1 Introduction.

This chapter describes the external components of the switch.

Chapter 2 Installation.

This chapter illustrates how to install the switch.

Chapter 3 Lightning Protection.

This chapter illustrates how to prevent lightning damage.

Chapter 4 Connection.

This chapter illustrates how to do the physical connection of the switch.

Appendix A Troubleshooting.

Appendix B Specifications.

Audience

This Installation Guide is for:

Network Engineer Network Administrator

Conventions

• The figures in Chapter 2 to Chapter 4 are for demonstration purposes only. Your switch may differ

in appearance from that depicted.

• This Guide uses the specific formats to highlight special messages. The following table lists the

notice icons that are used throughout this guide.

Remind to be careful. A caution indicates a potential which may result in device damage.

Remind to take notice. The note contains the helpful information for a better use of the

product.

Related Document

This Installation Guide is also available in PDF on our website. To obtain the latest

documentation and product information, please visit the official website:

http://www.tp-link.com

10/100Mbps Unmanaged Switch

II Contents

Contents

Chapter 1 Introduction ——————————— 01

1.1 Product Overview ...........................................................01

1.2 Features..............................................................................01

1.3 Appearance.......................................................................01

Chapter 2 Installation ——————————— 05

2.1 Package Contents ..........................................................05

2.2 Safety Precautions.........................................................05

2.3 Installation Tools..............................................................07

2.4 Product Installation ........................................................08

Chapter 3 Lightning Protection ——————— 10

3.1 Cabling Reasonably........................................................10

3.2 Connect to Ground.........................................................12

3.3 Equipotential Bonding...................................................13

3.4 Use Lightning Arrester..................................................14

Chapter 4 Connection ——————————— 16

4.1 Ethernet Port ....................................................................16

4.2 Verify Installation.............................................................16

4.3 Power On............................................................................16

4.4 Initialization........................................................................17

Appendix A Troubleshooting ———————— 18

Appendix B Specications ————————— 19

10/100Mbps Unmanaged Switch

01Introduction

Chapter 1 Introduction

1.1 Product Overview

TL-SF1016/TL-SF1016DS/TL-SF1024/TL-SF1024D/TL-SF1048 switch provides

16/24/48 10/100Mbps Auto-Negotiation RJ45 ports. Each port of the TL-SF1016/TL-

SF1016DS/ TL-SF1024/TL-SF1024D/TL-SF1048 supports auto MDI/MDI-X function,

eliminating the need for crossover cables or Uplink ports. The switch is Plug-and-Play

and any port can be simply plugged into a server, a hub or a switch, using straight cable

or crossover cable.

The TL-SF1016/TL-SF1016DS/TL-SF1024/TL-SF1024D/TL-SF1048 16/24/48-port

10/100Mbps Fast Ethernet Switch provides you with a low-cost, easy-to-use, high-

performance, seamless and standard upgrade to improve your old network to a

100Mbps network. It will boost your network performance up to full duplex data

transfer.

1.2 Features

■Complies with IEEE802.3, IEEE802.3u standards

■16/24/48 10/100Mbps Auto-Negotiation RJ45 ports supporting Auto- MDI/MDIX

■Supports IEEE802.3X flow control for full-duplex mode and backpressure for half-

duplex mode

■LED indicators for monitoring power, link, activity, speed

■Rack-mountable steel case

■Internal power supply

1.3 Appearance

■Front Panel

The front panel of TL-SF1016 is shown as the following figure.

Figure 1-1 Front Panel of TL-SF1016

10/100Mbps

RJ45 Port

LEDs

10/100Mbps Unmanaged Switch

02 Introduction

The front panel of TL-SF1016DS is shown as the following figure.

Figure 1-2 Front Panel of TL-SF1016DS

10/100Mbps

RJ45 Port

LEDs

The front panel of The TL-SF1024 is shown as the following figure.

Figure 1-3 Front Panel of TL-SF1024

10/100Mbps

RJ45 Port

LEDs

The front panel of The TL-SF1024D is shown as the following figure.

Figure 1-4 Front Panel of TL-SF1024D

10/100Mbps

RJ45 Port

LEDs

The front panel of The TL-SF1048 is shown as the following figure.

Figure 1-5 Front Panel of TL-SF1048

10/100Mbps

RJ45 Port

LEDs

10/100Mbps Unmanaged Switch

03Introduction

LEDs

LED Status Indication

Power

On The switch is powered on

Off The switch is powered off or power supply is

abnormal

Flashing Power supply is abnormal

Link/Act

On A device is linked to the corresponding port

Flashing Data is being transmitted or received

Off There is no device linked to the corresponding

port

100Mbps

On The corresponding port is running at 100Mbps

Off There is no device linked to the corresponding

port or the port is running at 10Mbps

Note:

Because of the dierence among the switch models, some switches don’t have

the 100Mbps indicator, such as TL-SF1048, TL-SF1016DS and TL-SF1024D

switch.

10/100Mbps RJ45 Port

Designed to connect to the device with a bandwidth of 10Mbps or 100Mbps. Each

has a corresponding 10/100Mbps LED.

■Rear Panel

The rear panel of the switch is shown as the following figure.

Figure 1-6 Rear Panel

Power

Socket

Grounding

Terminal

Grounding Terminal

The switch already comes with lightning protection mechanism. You can also ground

the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable.

For detailed information, please refer to Chapter 3 Lightning Protection.

10/100Mbps Unmanaged Switch

04 Introduction

Power Socket

Connect the female connector of the power cord here, and the male connector to

the AC (Alternating Current) power outlet. Please make sure the voltage of the power

supply meets the requirement of the input voltage.

Caution:

Please use the provided power cord.

10/100Mbps Unmanaged Switch

05Installation

Chapter 2 Installation

2.1 Package Contents

Make sure that the package contains the following items. If any of the listed items is

damaged or missing, please contact your distributor.

One Power Cord

One Switch

This Installation Guide

Installation Guide

BusinessNetworking Solution

Two mounting brackets and

the ttings

2.2 Safety Precautions

To avoid any device damage and bodily injury caused by improper use, please observe

the following rules.

■Safety Precautions

■Keep the power off during the installation.

■Wear an ESD-preventive wrist strap, and make sure that the wrist strap has a good skin

contact and is well grounded.

■Use only the power cord provided with the switch.

■Make sure that the supply voltage matches the specifications indicated on the rear

panel of the switch.

■Ensure the vent hole is well ventilated and unblocked.

■Do not open or remove the cover of the switch.

■Before cleaning the device, cut off the power supply. Do not clean it by the waterish

cloth, and never use any other liquid cleaning method.

10/100Mbps Unmanaged Switch

06 Installation

■Site Requirements

Temperature/Humidity

40℃

0℃

Please keep a proper temperature and humidity in the equipment room. Too high/low

humidity may lead to bad insulation, electricity leakage, mechanical property changes

and corrosions. Too high temperature may accelerate aging of the insulation materials

and can thus significantly shorten the service life of the device. For normal temperature

and humidity of the device, please check the following table.

Environment Temperature Humidity

Operating 0℃to 40℃10% to 90%RH Non-condensing

Storage -40℃to 70℃5% to 90%RH Non-condensing

Clearness

The dust accumulated on the switch can be absorbed by static electricity and result

in poor contact of metal contact points. Some measures have been taken for the

device to prevent static electricity, but too strong static electricity can cause deadly

damage to the electronic elements on the internal circuit board. To avoid the effect of

static electricity on the operation of the Switch, please attach much importance to the

following items:

■Dust the device regularly, and keep the indoor air clean.

■Keep the device well grounded and ensure static electricity has been transferred.

Electromagnetic Interference

Electronic elements including capacitance and inductance on the device can be

affected by external interferences, such as conducted emission by capacitance

coupling, inductance coupling, and impedance coupling. To decrease the interferences,

please make sure to take the following measures:

■Use the power supply that can effectively filter interference from the power grid.

■Keep the device far from high-frequency, strong-current devices, such as radio

transmitting station.

■Use electromagnetic shielding when necessary.

Otros manuales para TL-SF1016DS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de TP-Link

TP-Link

TP-Link JetStream TL-SG5412F Manual de instrucciones

TP-Link

TP-Link TL-SG2216 Manual de usuario

TP-Link

TP-Link JetStream TL-SL5428E Manual de instrucciones

TP-Link

TP-Link TL-SL1218P Manual de usuario

TP-Link

TP-Link JetStream TL-SL5428E Manual de instrucciones

TP-Link

TP-Link HS210 KIT Manual de usuario

TP-Link

TP-Link TL-SG1016DE Manual de usuario

TP-Link

TP-Link JetStream T1500G-10MPS Guía de inicio rápido

TP-Link

TP-Link Omada DS105G-M2 Manual de usuario

TP-Link

TP-Link 24+2/24+2G Manual de usuario

TP-Link

TP-Link JetStream TL-SG2210P Manual de usuario

TP-Link

TP-Link TL-SG1008P Manual de usuario

TP-Link

TP-Link tapo S505 Manual de usuario

TP-Link

TP-Link TL-SG2216 Manual de instrucciones

TP-Link

TP-Link JetStream T1500-28PCT Manual de usuario

TP-Link

TP-Link JetStream TL-SL5428E Manual de usuario

TP-Link

TP-Link TL-SG1024 Manual de usuario

TP-Link

TP-Link TL-SF1008D - 10/100M FAST ETHERNET SWITCH Manual de usuario

TP-Link

TP-Link POE150S Manual de usuario

TP-Link

TP-Link JetStream TL-SL5428E Manual de instrucciones

TP-Link

TP-Link T2500-28TC Manual de usuario

TP-Link

TP-Link Tapo H100 Manual de usuario

TP-Link

TP-Link TL-SG605E Manual de usuario

TP-Link

TP-Link JetStream TL-SG2008 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario