Totally Wicked OPTIMUS Manual de usuario

USER MANUAL

ELECTRONIC CIGARETTE KIT

CONGRATULATIONS ON PURCHASING YOUR

TOTALLY WICKED OPTIMUS

ELECTRONIC CIGARETTE KIT.

Sliding Top Cap

Mouthpiece

Airﬂow Control Ring

OLED Screen

Left/Right Adjustment Buttons

USB Charging Port

LED Indicator Light

4 5

For those familiar with

e-cigarettes, the steps below can

be followed to allow the device to

be used in the shortest possible

time:

• Prime the atomizer head

• Fill the tank

• Switch the Optimus on

• Set the Optimus to power mode

• Check the power setting

(we suggest 50 watts)

• Press the power button and inhale

• Charge the battery (it will possibly

not have been shipped with a full

charge)

Detailed descriptions of these

steps and more are given in the

full user guide to follow.

Priming the Atomizer Head and

Filling the Tank:

Note: It is important to “prime” a

new atomizer head before ﬁrst use.

Failure to do so can cause the

atomizer coil to overheat, leading to

an unpleasant taste and sometimes

irreversible damage to the atomizer

head requiring early replacement.

Quick Start Guide Using Your Optimus Kit

6 7

Priming the Atomizer Head and

Filling the Tank:

Turn the Slider Optimus tank upside

down and unscrew the atomizer

base from the glass section of the

tank. Prime the ﬁtted atomizer head

by slowly dripping E-liquid onto

the wire mesh and cotton, avoid

dripping E-liquid directly down

the centre of the atomizer head.

Continue to slowly drip E-liquid onto

the wire mesh and cotton until the

cotton visible through the sides of

the atomizer head changes colour.

Reﬁt the atomizer base onto the

glass section of the tank then screw

the assembled tank back onto

the Optimus battery. Slide the top

cap open by pushing ﬁrmly in the

indicated direction to expose the ﬁll

hole. Insert the ﬁlling nozzle into the

ﬁll hole and ﬁll the tank being careful

not to overﬁll. Slide the top cap shut

after ﬁlling.

Note: After ﬁlling the tank and

priming a new atomizer head, it is a

good idea to let the atomizer head

‘PRIME’ further by waiting 5 minutes

before vaping to ensure the new

atomizer head is fully saturated with

E-liquid.

Atomizer Head Lifespan:

Atomizer heads do not last forever

and need to be periodically

replaced. Time in use before

replacement is required is generally

from a few days to several weeks

depending on power used, vaping

style, and ﬂavour and type of

E-liquid. A slight burnt taste, general

loss of vapour production, or a

reduction in ﬂavour intensity can all

be indicators that the atomizer head

requires replacement.

Powering On and Off:

To switch the Optimus on, quickly

press the power button 5 times.

The green indicator light will ﬂash

5 times and the screen will activate

indicating that the device is powered

on. To turn the Optimus off, quickly

press the power button 5 times.

Using Your Optimus Kit Using Your Optimus Kit

8 9

Setting the Correct Mode and

Wattage:

The atomizer heads supplied with

the Optimus are compatible with

wattage mode only, and will not work

in temperature control modes. To

set the Optimus to wattage mode,

quickly press the power button 3

times to enter the mode selection

menu, the screen will begin to

ﬂash, then keep pressing the right

adjustment button until the screen

displays power. Press the power

button once to conﬁrm the selection.

Now adjust the wattage by pressing

the left or right adjustment buttons

until the screen reads 50w. Lower

wattage settings will give a cooler

and less dense vapour than higher

power settings, higher power

settings will produce larger clouds of

vapour but too much power can lead

to poor ﬂavour, or even a burnt taste

in the vapour. Experiment to ﬁnd

your own favourite setting which will

generally be between 30W and 80W

with the atomizer head supplied.

Tip: Long pressing either of the

adjustment buttons allows speedy

changes to the wattage.

Using Your Optimus Kit Using Your Optimus Kit

Vaping:

Press and hold the power button as

you inhale the vapour. The green

indicator light will illuminate and the

screen will display a timer while the

power button is pressed.

Adjusting the Airﬂow:

If you ﬁnd the airﬂow too airy or

too restrictive while vaping, it can

be adjusted by rotating the airﬂow

control ring located on the atomizer

base. Experiment to ﬁnd your

preferred setting.

E-liquid Level:

To prevent the atomizer head

from becoming dry and burning

prematurely, ensure the E-liquid level

does not drop below half way down

the glass section of the tank.

Reﬁlling the Tank:

To ﬁll the tank, slide open the

top cap by pushing ﬁrmly in the

indicated direction to expose the ﬁll

hole. Insert the ﬁlling nozzle into the

ﬁll hole and ﬁll the tank being careful

not to overﬁll. Slide the top cap shut

after ﬁlling.

10 11

Atomizer Head Protection:

If the power button is held down

for longer than 10 seconds while

vaping the screen will display “Over

10s protection” and the Optimus

will refuse to power or produce any

vapour. Release the power button to

allow normal operation to return.

Charging the Battery:

The Optimus is charged by

connecting the charge port located

beneath the adjustment buttons to

a USB port or suitable wall adaptor

with the charging lead supplied. The

green indicator light will ﬂash when

the charge lead is ﬁrst inserted and

the screen will display an animated

battery icon while charging. Once

the battery is fully charged the

screen will switch off.

Weak Battery Alert:

If remaining battery charge drops

to 2.9 volts, the screen will display

“WEAK BATTERY” and wattage will

be reduced. Charge the Optimus

using the steps outlined in Charging

the Battery above, to allow normal

operation to resume.

Replacing the Atomizer Head:

To replace the atomizer head,

remove the Slider Optimus Tank

from the Optimus battery by

unscrewing at the atomizer base.

Turn the tank upside down, then

unscrew the atomizer base from the

glass section of the tank. Unscrew

the atomizer head from the atomizer

base and replace. Prime the new

atomizer head as described above.

Reassemble the tank and screw

the assembled tank back onto the

Optimus battery.

Using Your Optimus Kit Using Your Optimus Kit

12 13

Settings:

Stealth Mode:

If stealth mode is enabled, the

display will not activate while

pressing the power button to

vape. The display will still activate

whenever the adjustment buttons are

pressed to make changes to wattage

or change modes, or if the power

button is pressed brieﬂy. To enable

or disable stealth mode, ensure the

Optimus is powered on, then press

and hold the power button and left

adjustment button at the same time.

The screen will display “STEALTH

ON” if enabled and “STEALTH OFF”

if disabled.

Key Lock Mode:

Key lock mode prevents accidental

changes to the wattage or

temperature settings. To enable or

disable key lock mode, ensure the

Optimus is powered on, then press

and hold both adjustment buttons at

the same time to enable or disable

key lock mode. The screen will

display “KEY LOCK” when enabled

and “KEY UNLOCK” when disabled.

If key lock mode is enabled the

screen will display “KEY LOCK”

when the adjustment buttons are

pressed. Adjustments to power or

temperature settings cannot be

made until key lock mode has been

disabled.

Switch between Current, Puff

Counter or Total Time Vaping

Displayed:

Quickly press the power button 3

times to enter the mode selection

menu; the screen will begin to ﬂash.

Then press the left adjustment

button; the icon at the bottom of

the screen will begin to ﬂash. Keep

pressing the right adjustment button

to cycle between puff counter/total

time vaping/current drawn from

the battery. Press the power button

once to conﬁrm the selection. If

Using Your Optimus Kit Using Your Optimus Kit

14 15

puff counter is enabled, the icon

will display the number of the

times the power button has been

pressed to vape. If total time vaping

is enabled, the icon will display the

total time spent vaping in seconds.

If amperage is enabled, the icon will

display how much current is drawn

from the battery when the power

button is held down to vape.

Note: you can reset the puff counter

and total time vaping to zero by

holding down the power button while

the respective icon is ﬂashing.

Rotating the Display:

To rotate the display by 180°, turn

the Optimus off then press and hold

both adjustment buttons at the same

time. Turn the Optimus back on.

Temperature Control Settings:

Switching to Temperature Control

Vaping Modes:

Temperature Control vaping modes

can be used only when speciﬁc

coil materials have been used for

atomizer head manufacture, namely

nickel (NI), titanium (TI) or stainless

steel (SS). To select the appropriate

temperature control mode, quickly

press the power button 3 times to

enter the mode selection menu;

the screen will begin to ﬂash. Then

press the right adjustment button to

cycle between the modes of power,

temperature or TCR. Once “TEMP”

is displayed and ﬂashing, press

the left adjustment button once

then NI, TI or SS will ﬂash. Keep

pressing the right adjustment button

to cycle between nickel, titanium

or stainless steel. Press the power

button once to conﬁrm the selection.

Only atomizer heads with coils

made from nickel, titanium or “316”

stainless steel are compatible with

temperature control mode. Select

Using Your Optimus Kit Using Your Optimus Kit

16 17

the appropriate mode to match your

atomizer type.

Note: the atomizer heads supplied

with the Optimus kit are compatible

with wattage mode only, and will not

work in temperature control mode.

Adjusting Wattage in Temperature

Control/TCR Modes:

The maximum wattage that is

applied in Temperature Control

or TCR modes can be adjusted.

Higher wattages allow the target

temperature to be reached quicker,

while lower wattages increase

the time taken to reach the target

temperature. Setting the wattage

too low may prevent the target

temperature from being reached at

all. To adjust the maximum wattage,

quickly press the power button 3

times to enter the mode selection

menu; the screen will begin to ﬂash.

Then press the left adjustment

button twice, and the wattage icon

will begin to ﬂash. Press the right

adjustment button once (increasing

the wattage), then press either of

the adjustment buttons to increase

or decrease the wattage. When the

desired wattage is reached, press

the power button once to conﬁrm the

selection.

Temperature Adjustment:

When in temperature control or

TCR mode, use the left or right

adjustment buttons to adjust the

temperature from 100°C – 315°C

(200°F – 600°F). Lower temperature

settings give a cooler and less

dense vapour. Higher temperature

settings produce hotter vapour and

larger clouds of vapour, but can

lead to poor ﬂavour or even a burnt

taste. Experiment to ﬁnd your own

favourite setting.

Note: The screen displaying

“TEMP PROTECT” is not an error or

fault; it means the atomizer head has

reached or exceeded the set target

temperature.

Using Your Optimus Kit Using Your Optimus Kit

18 19

Switching between °C and °F:

Press and hold the right adjustment

button to increase the maximum

temperature to 315°C or 600°F , then

press the right adjustment button

once more. The unit of measure will

switch to Fahrenheit if previously

in Celsius mode, or Celsius if

previously in Fahrenheit mode. The

same can be achieved by pressing

and holding the left adjustment

button.

New Temperature Control

Atomizer Head Installation:

Follow the steps outlined in

Replacing the Atomizer Head above

to replace and prime the atomizer

head. After replacing an atomizer

head in temperature control mode,

the screen may display the message

“NEW COIL RIGHT, SAME COIL

LEFT”. Press the right adjustment

button once to conﬁrm a new

atomizer head has been ﬁtted, or

the left adjustment button if the

previously used atomizer head has

been replaced. Conﬁrmation of

a newly ﬁtted atomizer head with

the right adjustment button should

only be made when the atomizer

head is at room temperature. If the

atomizer head has recently been

used and is still warm, the Optimus

will not properly control atomizer

temperature. Allow any newly ﬁtted

atomizer head or tank to cool to

room temperature before conﬁrming

a new coil.

Reminder: Do not forget to prime

your new atomizer head before

ﬁrst use.

Using Your Optimus Kit Using Your Optimus Kit

Otros manuales de Cigarrillo electrónico de Totally Wicked

Totally Wicked

Totally Wicked GRIP Manual de usuario

Totally Wicked

Totally Wicked Curve Lite Manual de usuario

Totally Wicked

Totally Wicked Revolution S Manual de usuario

Totally Wicked

Totally Wicked Polka Manual de usuario

Totally Wicked

Totally Wicked GRIP VT75 Manual de usuario

Totally Wicked

Totally Wicked Forza 75 Manual de usuario

Totally Wicked

Totally Wicked V-Pipe Manual de usuario

Totally Wicked

Totally Wicked Corsa Manual de usuario

Totally Wicked

Totally Wicked Tornado-T Manual de usuario

Totally Wicked

Totally Wicked AURA Manual de usuario

Totally Wicked

Totally Wicked Tornado EX2 Manual de usuario

Totally Wicked

Totally Wicked aio Slider Hellfire Manual de usuario

Totally Wicked

Totally Wicked e-lectron-L Manual de usuario

Totally Wicked

Totally Wicked ARC MINI Manual de usuario

Totally Wicked

Totally Wicked ARC EVO Manual de usuario

Totally Wicked

Totally Wicked Odyssey Pipe Manual de usuario

Totally Wicked

Totally Wicked arc pico Manual de usuario

Totally Wicked

Totally Wicked INTU QC 200 Manual de usuario

Totally Wicked

Totally Wicked Rocket Manual de usuario

Totally Wicked

Totally Wicked Curve 2 Mini Manual de usuario

Totally Wicked

Totally Wicked eGo-C+ Manual de usuario

Totally Wicked

Totally Wicked Odyssey Manual de usuario

Totally Wicked

Totally Wicked Tornado NX Manual de usuario

Totally Wicked

Totally Wicked Rival Manual de usuario

Manuales populares de Cigarrillo electrónico de otras marcas

STEAMAX

STEAMAX TFV8 X-BABY Manual de usuario

iQOS

iQOS 3 MULTI Manual de usuario

Vaporesso

Vaporesso LUXE XR MAX Manual de usuario

ZAZO

ZAZO PRO Mini 2 Manual de usuario

Aquafog

Aquafog Turbo XE Manual

Electronic Cigarettes Australia Pty Ltd

Electronic Cigarettes Australia Pty Ltd AUSSIE BLUE ENDURANCE Manual de usuario

UWELL

UWELL Whirl T1 Manual de usuario

VooPoo

VooPoo VMATE Manual de usuario

Yogs-Pfeifen

Yogs-Pfeifen E-PIPE nex KLASSIK Manual de usuario

TSI Instruments

TSI Instruments 3075 Manual de usuario

Vaporesso

Vaporesso GTX ONE Manual de usuario

VooPoo

VooPoo DRAG 2 Manual de usuario

Innova

Innova 3.0 Manual de usuario

Aquafog

Aquafog XE CRSM Manual de usuario

hi-Fun

hi-Fun hi-Cigarette Manual de usuario

Neptronic

Neptronic SKH Series Manual de usuario

Vaporesso

Vaporesso LUXE Q2 SE Manual de usuario

iQOS

iQOS 3 DUO Manual de usuario